• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.4
• /
• pp.299-309
• /
• 2014

When biped robots make turns, the ability to walk stably and precisely along any circular path is crucial. In this context, inverse kinematics solutions are found for accurate gait realization, and new zero moment point(ZMP) equations are derived with respect to the cyclindrical coordinate system to facilitate generation of stable walking patterns. Then, appropriate steady and transitional walking patterns are both proposed in form of time functons. Subsequently, walking patterns for a path but of different speeds are generated using the functions and associated formulas, and preliminarily checked for stability based on the ZMP equations. Upon comparison of those cases, one can see how and when robots may fall down during circular walking. Finally, those patterns are put to test on the sample robot by ADAMS(R) along with the inverse kinematics solutions and a new balance control scheme compensating for insufficient stability particulary during the initial transition period. Test results show that the robot can walk along the circular path as predicted at a resonably high speed despite the distributed mass and ground contact effects, validating effectiveness of the suggested approach.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.12
• /
• pp.1152-1159
• /
• 2013

This paper proposes an effective walking system for a hexapod robot on uneven terrain. To overcome the deficiencies of two-pair walking systems, which are effective on even terrain, the use of only three legs changes the steps required for movement. The proposed system receives feedback data from switches attached to the bottom of the legs and gyro sensor to carry out stable walking using the Bezier curve algorithm. From the coordinates of the Bezier curve, which guarantees the circular motion of legs, the motor's angle value can be obtained using inverse kinematics. The angle values are sent to each motor though RS-485 communication. If a switch is pushed by the surface during navigation in the Bezier curve pattern, the robot is designed to change its circular course. Through the changed course, each leg can be located on an optimal surface and the wobble phenomenon is reduced by using a normal vector algorithm. The simulation and experiment results show the efficiency of the proposed algorithm.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.236-241
• /
• 2008

This paper presents a method to recognize the plane regions for movement of walking robots. When the autonomous agencies using stereo camera or laser scanning sensor is under unknown 3D environment, the mobile agency has to detect the plane regions to decide the moving direction and perform the given tasks. In this paper, we propose a very fast method for plane detection using normal vector of a triangle by 3 vertices defined on a small circular region. To reduce the effect of noises and outliers, the triangle rotates with respect to the center position of the circular region and generates a series of triangles with different normal vectors based on different three points on the boundary of the circular region. The vectors for several triangles are normalized and then median direction of the normal vectors is used to test the planarity of the circular region. The method is very fast and we prove the performance of algorithm for real range data obtained from a stereo camera system.

• Physical Therapy Rehabilitation Science
• /
• v.11 no.4
• /
• pp.384-390
• /
• 2022

Objective: The purpose of this study was to investigate the effect of the side-step tasks based circular training program (STCT) on balance and gait characteristics in stroke patients. Design: A randomized controlled trial Methods: Twenty-four stroke patients were randomly divided into two groups of twelve patients each. One group was applied with the STCT whereas the other group was treated with conservative physiotherapy (CP). The ability of gait was measured in 10m walking test and stride length on both side using BTS G-WALK (BTS Bioengineering S.p.A, Italy) and the ability of balance was measured in Berg Balance Scale (BBS) and Timed Up and Go Test (TUG). Results: The STCT group was significant differences in the balance parameters of BBS and TUG (p<0.05) and showed significant differences in gait variables in 10m walking speed, stride length of affected and non-affected side after the experiment before and after the experiment (p<0.05). In addition, the STCT group showed a significant difference in BBS compared to the control group (p<0.05). Conclusions: The results of this study confirmed that the side-step tasks based circular training program (STCT) improves balance and walking ability in stroke patients. STCT is expected to be used as a useful intervention method for stroke rehabilitation.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.5
• /
• pp.1395-1403
• /
• 2016

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1926-1930
• /
• 2004

We suggest a turning gait planning of a quadruped walking robot with an articulated spine. Robot developer has tried to implement a gait more similar to that of natural animals with high stability margin. Therefore, so many types of walking robot with reasonable gait have been developed. But there is a big difference with a natural animal walking motion. A key point is the fact that natural animals use their waist-oint(articulated spine) to walk. For example, a crocodile which has short legs relative to a long body uses their waist to walk more quickly and to turn more effectively. The other animals such as tiger, dog and so forth, also use their waist. Therefore, this paper proposes discontinuous turning gait planning for a newly modeled quadruped walking robot with an articulated spine which connects the front and rear parts of the body. Turning gait is very important as same as straight gait. All animals need a turning gait to avoid obstacle or to change walking direction. Turning gait has mainly two types of gaits; circular gait and spinning gait. We apply articulated spine to above two gaits, which shows the majority of an articulated spine more effectively. Firstly, we describe a kinematic relation of a waist-joint, the hip, and the center of gravity of body, and then apply a spinning gait. Next, we apply a waist-joint to a circular gait. We compare a gait stability margin with that of a conventional single rigid body walking robot. Finally, we show the validity of a proposed gait with simulation.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.10a
• /
• pp.139.1-139
• /
• 1999

• Korean Journal of Applied Biomechanics
• /
• v.16 no.2
• /
• pp.193-205
• /
• 2006

This study was to analysis the kinematic and kinetic differences between new walking shoe(NWS : RYN) and general walking shoe(GWS). The subjects for this study were 10 male adults who had the walking pattern of rearfoot shrike with normal foot. The movement of one lower leg was measured using plantar pressure and Vicon Motion Analysis Program(6 MX13 and 2 MX40 cameras : 100 f / s) while the subjects walked at the velocity(1.5m/s. on 2m).. The results of this study was as follows : 1. The NWS was better than the GWS that caused injuries such as adduction, abduction and pronation are reduced While walking on a perpendicular surface, the landing angle and the knees angles were extensive which makes walking more safe which reduces anxiety and uneasiness. 2. The bottom of the NWS were now made into a more circular arch which supports the weight of the body and reduces the irregular angles when wearing GWS. This arch made the supporting area more wide which made the upholding the trunk of the body more effective. The whole bottom of the foot that supports the weight is more flexible in addition, increases the safeness of walking patterns and the momentum of the body. 3. The moment the heel of the foot of the NWS touch the ground, the range of the pressure were partially notable and the range of the pressure on the upper part of the thigh were dispersed The injuries that occurred while walking. primary factors when a shock related injuries are reduced Judgements of the impacts of the knees and the spinal column dispersing could be made.

• Journal of Biosystems Engineering
• /
• v.32 no.5
• /
• pp.339-347
• /
• 2007

A hexapod walking robot had been developed for gathering information in the field. The developed robot was $260{\times}260{\times}130$ ($W{\times}L{\times}H$, mm) in size and 14.7 N in weight. The legs had nineteen degrees of freedom. A leg has three rotational joints actuated by small servomotors. Two servomotors placed at ankle and knee played the roles of vertical joint for up and down motions of the leg and the other one placed at coxa played the role of horizontal joint for forward and backward motions. In addition, a servomotor placed at thorax between the front legs and the middle legs played the role of vertical joint for pumping the two front legs to climb stair or inclination. Walking motion of the robot was executed by tripod gait. The robot was controlled by manual remote-controller communicated by an infrared ray. Two controllers were equipped to control the walking of the robot. The sub-controller using PIC microcomputer (Microchips, PIC16F84A) received the 16 bit command signal from the manual remote controller, decoded it to 8bit and transmitted it to the main microcomputer (RENESAS, SH2/7045), which controlled the 19 servomotors using the PWM command signals. Walking speeds were controlled by adjusting the period of command cycle and the stride. Forward walking speed were within 100 cm/min to 300 cm/min. However, experimental walking speed had the error of 4-40 cm/min to compare with the theoretical one, because of slippage of the leg and the circular arc motion of servomotor of coxa.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.1 s.190
• /
• pp.118-125
• /
• 2007

In this study, we analyzed the plantar shear stress and normal pressure in lateral heel diabetic foot patients during walking by using in-shoe local shear stress and plantar pressure measurement systems. The shear force transducer based on the magnetic-resistive principle, was a rigid 3-layer circular disc. Shear transducers were mounted on the locations of four metatarsal heads and heel in the insole. Twelve normal subjects and three diabetic foot patients with diabetic neuropathy in the lateral heel participated in this study. The center of pressure in lateral heel diabetic foot patients moved more medially and directed toward the first, medial to the second metatarsal heads, and the hallux during late stance, making pressure at the medial heel and the second metatarsal head significantly larger than in the normal. Shear stress at the heel changed significantly in early stance and the magnitude of shear stresses in each metatarsal head also changed. Further studies would be very helpful to design foot orthoses in patients with diabetic neuropathy or other diseases.