• 한국산업보건학회지
• /
• 제5권2호
• /
• pp.137-146
• /
• 1995

Twenty(20) large commercial buildings located in Seoul with friable sprayed-on surface insulation material on ceilings were investigated for asbestos content in bulk material by polarized light microscopy and for airborne fiber concentrations in buildings by phase contrast microscopy. In addition, such building-related variables as building age, numbers of traffic, airflow, surface conditions of the ceiling, temperature, and humidity were studied for any correlation with airborne fiber concentrations. The results were as follows: 1. Chrysotile asbestos was found in two bulk samples with 3-5% content and with <1%in one sample out of total 20 bulk samples collected. Glass fiber and mineral wool were the two major constituents of the bulk samples. 2. The ceiling surfaces were very friable in 16 buildings and were relatively hard in 4 buildings. The friability of the surface material was dependent upon the type and the amount of binder that had been mixed with the sprayed-on surface material. 3. Airborne fiber concentrations were log-normally distributed and the geometric mean(geometric standard deviation) fiber concentrations in the underground parking lots, inside buildings, and outdoor ambient air were 0.0063(1.97)f/cc, 0.0068(2.29)f/cc, and 0.0033(2.36)f/cc, respectively. 4. No significant relationship of airborne fiber concentrations and all building-related variables studied except humidity was found. The results of this study suggest that the sprayed-on surface insulation material found in some commercial buildings may possibly be contaminated with asbestos. Since most of the ceiling surfaces surveyed were very friable and poorly maintained and the airborne fiber concentrations were relatively high, there is a possibility of asbestos fiber contamination in these buildings, particularly at those buildings with asbestos-contaminated surface material. Since poorly maintained surface conditions were thought to be a source of high airborne fiber concentrations, there is a urgent need of a systematic operation and maintenance program. Further study of non-occupational asbestos exposure in general population utilizing advanced analytical technique such as transmission electron microscopy is highly recommended.

• 한국산업보건학회지
• /
• 제20권2호
• /
• pp.88-93
• /
• 2010

To confirm and quantify asbestos fibers released from the asbestos-cement slate roofs due to weathering, three houses, selected based on the year of built - 60's, 70, and 80's, were investigated. All of them were located in the downtown of Seoul. Rain or snow-melt water was collected from the roof in a 3.5 liter plastic bottle. A known amount of collected water was filtered on the 37 mm membrane filter, ashed in a muffle furnace, and subsequently treated with HCl to remove organic material. The treated remaining was refiltered on a 25mm membrane filter for PLM and PCM analyses. The NIOSH 7400 method was utilized for PCM counting. In addition, SEM/EDX was used to confirm the asbestos types. The results of this study showed that chrysotile fibers were confirmed by PLM in all samples analyzed. A significant amount of asbestos fibers were found in the water samples. The ranges of asbestos fibers counted from the samples collected in the 60's, 70's, and 80's were; 10,406.3~55,575.6 f/L, 5,218.8~38,126.2 f/L, and 2,906.3~7,798.6 f/L, respectively. As anticipated, concentrations of asbestos fibers increased with time of installment of the roofing material. We conclude that weathering can be a significant factor on the release of asbestos fibers from the asbestos cement products. Since asbestos fibers released into environment can be a source of significant health hazard, countermeasures, such as replacement, removal, and encapsulation of weathered asbestos slate, should be initiated immediately.

• 한국광물학회지
• /
• 제10권2호
• /
• pp.126-138
• /
• 1997

Serpentinite of the Yesan-Gongju-Cheongyang area has been formed by serpentinization of ultramafic rocks. The ultramafic rock might be composed mainly of oilvine with minor pyroxene and amphibole. Olivine has a considerably restricted chemical compositional ranging from Fo90 to Fo93. Fresh serpentinite containing large amount of oilvine is usually massive in occurrence and dark green to black in color. Serpentine minerals occur not only as major mineral of serpentinite, but also as remnants in the talc ore which was formed from serpentinite. XRD study indicates that antigorie is the most abundant serpentine mineral of the serpentinite. Serpentinite consisting of antigorite usually shows non-pseudomorphic texture, whereas that consisting of lizardite shows pseudomorphic texture. Antigorite is found along the margins or fractures of olivine grains resulting in the formation of network of magnetite which was formed at the time of serpentinization. Lizardite, subordinate constituent mineral of serpentinite, frequently shows pseudomorphic mesh-texture after olivine. The chemical differences between antigorite and lizardite/chrysotile are small, so both minerals are not easily discernible with the electron microprobe. Antigorite occuers as elongate blades, flakes, or plates forming interpenetrating texture to obliterate previous textures. SEM study also shows that most serpentine minerals occur in platy or tabular form rather than in asbestiform. Fractures formed after main serpentinization are observed within the pseudomorphic central olivine grain. Careful observation of the serpentine pseudomorphs gives a great deal of data on the pre-serpentinization nature of the serpentine pseudomorphs gives a great deal of data on the pre-serpentinization nature of the ultramafic rocks. It is inferred that the serpentinization took place after the emplacement of ultramafic body into the relatively wet environment ceased and the cooling intrusive body crossed into the stability field of serpentine. It is inferred that the final pervasive serpentinization took place over a long time, by hydrothermal water supplied through the fracture system produced during emplacement of ultramafic rock.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2005년도 INTERNATIONAL SYMPOSIUM ON SOIL & GROUNDWATER ENVIRONMENT
• /
• pp.158-159
• /
• 2005

This study showed that the highest temperature point of the Dongrae thermal spring in Pusan was moved to the north direction of the Dongrae fault as times goes by. The Br concentration(1.5mg/L) in Dongrae thermal waters indicated the influence of 2% seawater mixing. If the simple mixing without hydrochemical reaction occurs between seawater and thermal water, the concentration of Mg will be about 20mg/L. But the low concentration(0.1 mg/L) of Mg, contrary to high concentration(10 mg/L) of surrounding groundwater not affected by thermal water, suggested the thermal water, seawater and rock interactions. The calculation of saturation index(SI) by using the geochemical code of EQ3NR showed that the Mg in thermal groundwater, which was introduced by seawater, was removed by the precipitation of Antigorite (SI: log Q/K =71.753, $Mg_{48}Si_{24}O_{85}(OH)_{62}$) and Tremolite (SI: 8.463, $Ca_2Mg_5Si_8O_{22}(OH)_2$), Talc (SI: 6.409, $Mg_3Si_4O_{10}(OH)_2$), Dolomite (SI: 2.014, $CaMg(CO_3)_2$), Chrysotile (SI: 3.698, $Mg_3Si_2O_5(OH)_4$) in the crack of fault zone. The highest temperature point in the study area will move to north direction and stop in the Jangjun area without the input of seawater.

• 한국산업보건학회지
• /
• 제20권1호
• /
• pp.63-69
• /
• 2010

This study was conducted to compare the concentration of various air contaminants in nine different laboratories during routine activities. Volatile organic compounds (VOC) were sampled and analyzed using NIOSH Method 1500 and asbestos fibers were sampled and analyzed using NIOSH Method 9002 and 7400. Detectable levels of acetone, toluene and ethanol were found in all the laboratories and xylene and n-hexane were detected in eight of the nine laboratories. All the VOC concentrations were well below the Korean Ministry of Labor's Exposure Limit and American Conference of Governmental Industrial Hygienists' (ACGIH) Threshold Limit Values (TLVs). Total VOC concentrations at the university laboratories were significantly higher than those at governmental agency laboratories. Airborne fiber concentrations were below 0.01 fibers/cc, while the concentration of chrysotile was 2% in insulation materials sprayed on the ceiling of one laboratory. While all the governmental agency laboratories (n=4) had fume hoods, two out of the five university laboratories did not have fume hoods. The capture velocity of half of the fume hoods were below the maintenance standard(0.4 m/sec). In conclusion, the study suggests that the current controls in place at both university and government agency laboratories are not sufficient in limiting exposure to harmful chemicals to non-detectable levels, though they appear to be adequate in protecting workers to levels below applicable occupational exposure limits. The study also suggests that researchers working in university laboratories may be exposed to greater levels of contaminant than those working in government agency laboratories.

• 한국대기환경학회지
• /
• 제23권6호
• /
• pp.718-726
• /
• 2007

There are many varieties of asbestos: chrysotile, crocidolite, amosite, tremolite, actinolite, and anthophylite. These are widely used in construction materials, brake lining, textile, and so on. Even though non-asbestos fibers such as glassfiber and rockwool have manufactured because asbestos causes asbestosis, lung cancer, mesothelioma, etc., some bad effects of non-asbestos have been also reported. PCM (phase contrast microscopy) and PLM (polarized light microscopy) have been used to qualitatively analyze asbestoses. These techniques have serious drawbacks when identifying and separating various asbestoses. Recently scanning electron microscopy (SEM) equipped with energy dispersive X-ray analysis (EDX) has been known as an useful tool to analyze airborne particle since it provides physical and chemical information simultaneously. The purpose of the study was to classify both asbestos and non-asbestos fibers and finally to develop their source profiles by using the SEM/EDX. The source profiles characterized by 6 different types of asbestos fibers and 2 types of non-asbestos fibers had been developed by analyzing a total of 380 fibers. Analytical parameters used in this study were length, width, aspect ratio, and shape as physical information, and Na, Mg, Al, Si, K, Ca, Cr, Mn, Fe, and Cu as chemical information. All the parameters were intensively reviewed.

• 분석과학
• /
• 제27권3호
• /
• pp.153-160
• /
• 2014

세계적으로 석면분석방법에 관한 다양한 연구사례가 발표되고 있는 가운데, 분석방법의 차이에 따른 석면함유물질(ACM, Asbestos Containing Material) 결과에 대한 관심이 대두되고 있다. 본 연구에서는 균질성이 확보된 ACM 시료를 시야평가법(visual estimation method)과 포인트계수법(point counting method)의 분석결과에 대한 비교 평가를 통하여 분석기관 및 분석자의 신뢰성 향상과 더불어 편광현미경 분석의 기초자료를 확보고자 하였다. 석면분석은 정성분석과 정량분석으로 구분하였으며, 석면정량을 위한 방법은 EPA 600-R-93-116의 시야평가법과 포인트계수법으로 총 400지점을 계수하는 방법으로 실시하였다. 먼저 준비된 시료의 균질성을 분산분석을 이용하여 확인한 결과 이상이 없음을 확인하였다. 정성분석의 결과는 백석면과 갈석면으로 확인되었고 정량분석결과는 포인트계수법이 시야평가법과 비교하여 전체적인 석면함유량이 저평가되는 경향과 함께 포인트계수법은 분석과정이 조금 복잡하고 분석시간이 많이 소요되었다.

• 한국산업보건학회지
• /
• 제21권3호
• /
• pp.123-127
• /
• 2011

Objectives: The purpose of this study was to investigate the status of asbestos-containing materials (ACMs) used on ships and to consider measures for preventing worker exposure to asbestos fibers. Methods: A total of 17 ships including 16 ships under repair and a ship under construction at shipyards in Korea were investigated. Bulk samples were collected from suspected ACMs on engine exhaust pipes, boiler steam pipes, generator exhaust pipes, and etc. in ships in order to identify the presence of ACMs. Types and contents of asbestos were determined using polarized light microscopy (PLM). Results: ACMs were found from 14 ships out of 17 ships investigated. Only chrysotile asbestos was found from all samples. ACMs were mainly found from samples collected at the exhaust pipes of the engine, generator and incinerator, and boiler steam pipes where exhaust gases or steam of high temperature pass through. In most cases, types of ACMs were asbestos-containing fabrics such as asbestos tape. Friable ACMs were also found in some cases. Use of ACMs on ships was relevant to built time and owner of the ships rather than type and tonnage of the ships. Conclusions: ACMs were found from most ships built prior to 2000s. Therefore, measures for preventing asbestos-related diseases such as preparation of asbestos map on the ship and installation of warning signs, hazard communication with workers (ship-repairing workers, engine room workers and etc.), and follow-up for worker's health management are needed.

• 한국대기환경학회지
• /
• 제24권3호
• /
• pp.346-356
• /
• 2008

Asbestos is the name of a group of minerals with long and thin fibers that originate naturally in the environment. Asbestos mainly affects lungs and the membrane that surrounds the lungs. In general, PCM (phase contrast microscopy) and PLM (polarized light microscopy) have been used to analyze asbestos fibers. However, these methods have often problems to over-estimate number concentration when counting real asbestos fibers. Moreover, there are many difficulties when separating and identifying various asbestos and non-asbestos fibers. In order to determine quantitative information on fibrous particles, source profiles for asbestos and non-asbestos fibers must be initially developed on the basis of their chemical compositions and physical parameters. In our study, a SEM/EDX was used to develop source profiles from known asbestos samples as reference samples. We could make the source profile matrix consisting of 6 types of asbestos fibers and 2 types of non-asbestos fibers by analyzing 380 fibers. Based on these profiles, a rule building expert system was developed by using the visual basic application (VBA). Various fibers were successfully classified by 2 simple rules in the EXCEL environment based on several visual steps such as inserting data, viewing results, and saving results. For a case study to test the expert system, samples from a construction materials and from various indoor environments such as a residental area, a preschool classroom, and an underground store were collected and analyzed. As a result of the survey, a total of 76 individual test fiber particles was well classified into 5 different types of particle classes; 9.3% of chrysotile, 15.4% of amosite, 0.8 of crocidolite, 4.2% of tremolite, 5.8% glass fiber, 21.1% of other fibers, and 43.5% of unknown fibers in terms of number concentration. Even though unknown portion was high, it will be decreased markedly when expanding fiber source profiles.

• 한국광물학회지
• /
• 제26권2호
• /
• pp.87-99
• /
• 2013

국내 주요 백운석 광산에서 산출되는 백운석 광석과 수반광물에 대하여 X-선회절분석, 박편관찰, 주사전자현미경 관찰 등을 통하여 광물학적 및 조직 특성을 분석하고, 이들의 산출상태와 성인을 검토하였다. 연구 결과, 백운석 광석은 담회색에서 암회색을 띠며 입자도 세립에서 조립까지 다양하였으나, 주로 거의 순수한 돌로마이트로 이루어졌다. 일부 백운암에서는 소량의 방해석, 석영, 운모가 함유되었다. 세맥, 암맥, 변질부 등에서 국지적으로 방해석, 석영, 일라이트, 장석, 고령토광물, 녹니석 등이 산출되며, 일부 광산 변질부에서 세피올라이트와 규회석이 확인되었다. 그러나 이번 조사에서 온석면과 투각섬석과 같은 석면광물은 확인되지 않았다. 광산내 적갈색 및 황색을 띠는 점토물질들은 주로 일라이트로 구성되며, 카올린광물과 스멕타이트가 수반되기도 한다. 이들은 암맥관입과 관련된 부분적 열수변질과 이후의 풍화작용에 의해 형성된 것으로 보인다. 백운암층의 구성광물, 조직, 산출 상태와 기존의 연구결과로 볼 때, 백운석 광상은 선캄브리아기와 고생대의 얕은 바다에서 퇴적된 석회질 퇴적물이 속성작용에 의해 백운석화 작용을 받아 형성된 것으로 보인다.