The objective in this study was investigated temperature susceptibility and low temperature fracture of rubber modified asphalt. A chlorinated polyethylene elastomer, Tyrin CM0730, was added to 200/300 grade asphalt with 3.0 and 5.0wt% to improve campatibility. The elastomer modified asphalts were analyzed for temperature susceptibility relating to penetration index(PI) and penetration-viscosity number(PVN) as well as low temperature fracture relating to fracture energy $(G_{IC})$. These indices were obtained from the measurements of penetration, viscosity, failure load and modulus. The addition of small amounts of elastomer to the asphalt resulted in a significant increase of both the PI and PVN over an unmodified asphalt. Also, the fracture energy increased with the addition of elastomer to asphalt. These significant improvement at both the high and low temperature result in enhanced performance.
Reactions between chlorinated or brominated poly(isobutylene-isoprene) (CIIR and BIIR, respectively) and 3-mercaptopropyltrimethoxysilane(MPS) were kinetically studied by gas chromatography in solution state. CIIR and BIIR were mixed with MPS and dibutyltin dilaurate as catalyst on roll mill and then the compounds were cured in hot water or atmosphere. From the gas chromatography, reaction order, activation energy, and frequency factor were determined. Crosslinking density and physical properties of moisture-cured CIIR and BIIR were measured. CIIR and BIIR were effectively moisture-cured and physical properties of these rubbers were comparatively good.
본 연구는 자동차 엔진의 구동을 각종 부대 장치로 전달하는데 사용되는 V-rib 벨트 재료의 내열성 및 내마모성을 향상시키기 위한 연구이다. 이를 위하여 고무 매트릭스는 EPDM과 CR, 그리고 충전제로 ZnO, 면 및 아라미드 섬유의 함량을 달리한 시편과 v-벨트를 만들어 내열성과 내마모성 그리고 기계적 성질을 조사하였다. CR 배합계에서 ZnO의 함량이 증가함에 따라 내마모성이 증가하였다. 또한 면섬유의 함량이 증가함에 따라 벨트상태에서 견딜 수 있는 구동시간은 증가하지만 내마모성은 감소하는 결과를 보였다. EPDM 배합계에서 면섬유의 충전한계는 30 phr정도였다. 또한 아라미드와 면섬유를 혼합 사용한 결과 구동시간과 내마모성을 동시에 증가시킬 수 있었으며, 그 단섬유의 최적 조성은 아라미드섬유/면섬유 비율이 1/5인 것으로 조사되었다. 동일한 면섬유 함량에서 EPDM 배합계 가 CR 배합계보다 우수한 물성을 보였다.
자동차의 와이퍼 블레이드(Wiper Blade, W/B)의 마찰계수를 낮추기 위하여 고무 표면을 염소 처리하였다. 염소처리 방법으로는 물 $20.0{\ell}$에 35.0% 염산(HCl)과 5.25% 차아염소산소다(NaOCl)를 각각 $300m{\ell}$, $400m{\ell}$를 첨가한 염소처리용액을 만든 후, 2분에서 20분 동안 처리하였다. 처리 후의 표면 특성은 IR 스펙트럼, 마찰계수 측정기, EPMA를 이용하였다. IR 스펙트럼으로 부터 W/B 고무 표면의 염소화 정도를 확인하였다. 마찰계수는 염소처리에 의해 크게 감소하였다. 특히, 염소화 초기에 보다 민감한 영향을 나타내었다. 고무표면 특성을 고무 파단면의 길이 방향에 대하여 EPMA 선분석한 결과를 얻었다. EPMA에 의한 염소침투깊이는 위의 염소농도에서, 염소처리를 5분 실시한 후에 1.2 ${\mu}m$ 임을 알 수 있었다.
Generally, a silicone rubber and a chlorinated polyethylene(CPE) have been used as a binder for the development of high-performance composite EM(Electro Magnetic) wave absorbers. In this paper, the EM wave absorption performance of natural lacquer, which is newly proposed as a binder was investigated. The prepared MnZn ferrite EM wave absorbers are mixed with natural lacquer showed excellent EM wave absorption characteristics compared with MnZn ferrite EM wave absorbers which are mixed with the conventional binders. MnZn ferrite EM wave absorbers mixed with natural lacquer were prepared and their absorption ability was also investigated The EM wave absorbers are fabricated in different proportions of MnZn, or NiZn ferrite and natural lacquer, and their reflection coefficients are measured. The permittivity and permeability are calculated by using the measured reflection coefficients. The EM wave absorption abilities are calculated according to different thicknesses of the EM wave absorbers.
한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.1
/
pp.157-161
/
2006
Generally, a silicone rubber and a chlorinated polyethylene(CPE) have been used as a binder for the development of high-performance composite EM(Electro Magnetic) wave absorbers. In this paper, the EM wave absorption performance of natural lacquer, which is newly proposed as a binder was investigated. The prepared MnZn ferrite EM wave absorbers are mixed with natural lacquer showed excellent EM wave absorption characteristics compared with MnZn ferrite EM wave absorbers which are mixed with the conventional binders. MnZn ferrite EM wave absorbers mixed with natural lacquer were prepared and their absorption ability was also investigated. The EM wave absorbers are fabricated in different proportions of MnZn, or NiZn ferrite and natural lacquer, and their reflection coefficients are measured. The permittivity and permeability are calculated by using the measured reflection coefficients. The EM wave absorption abilities are calculated according to different thicknesses of the EM wave absorbers.
Coating performance of various coating systems including chlorinated rubber and epoxy/urethane used most for steel structures of highway in Korea, was evaluated by exposing test specimen to complex deterioration factors such as ultraviolet ray, moisture, freeze-thaw cycle and salt. Deteriorated specimens were evaluated by chalking and rust grades according to ASTM, and measurement of color differences and adhesion. In overall coating performances such as corrosion resistance, photochemical stability, and adhesion, ceramic/ urethane, moisture-curable urethane/ urethane, etc. were superior. As for other coating materials tested in this study, superior materials against certain deterioration factors may be inferior against other factors. Accordingly, in order to select suitable maintenance coating materials for the use, it is thought that investigation of suitability through experiment should precede selection of materials, especially for unusual coatings or paints.
Various silanes, amino silane, vinyl silane, TESPD, and ZS (TESPD/zinc soap complex), are added into chlorinated isobutylene-isoprene copolymer (CIIR)/hard clay/carbon black (CB) compound and they are investigated with respect to the vulcanization characteristics, the processability, and the mechanical properties. In hard clay/CB filled system, only ZS silane added compound shows both lower Mooney viscosity and extrusion torque while vinyl silane added compound showed only a lower extrusion torque. All the ZS added compounds showed the lowest viscosity among them. The silane added compounds showed an increased modulus. In 'fatigue to failure' count test, the ZS added compound showed superior counts compared to other silane (amino, vinyl, TESPD) added compounds. The mechanical properties were significantly increased when the S2 and ZS were added into CIIR/hard clay/CB compound. The ZS added compounds showed a significant improvement on elongation modulus.
Various silanes, amino silane, vinyl silane, TESPD, and ZS (TESPD/zinc soap complex), are added into chlorinated isobutylene-isoprene copolymer (CIIR)/soft clay/carbon black (CB). The vulcanization characteristics, the processability, and the mechanical properties are measured. In soft clay/CB filled CIIR system, there are no significant changes in Mooney viscosity among compounds. Vinyl silane added compound shows a low extrusion torque. All the silane added compounds shows an increased modulus. The mechanical properties are significantly increased when the S2 is added into CIIR/soft clay/CB compounds.
In this study, performance tests, a field evaluation, and a life cycle cost (LCC) analysis for high performance coating systems were conducted to prepare a plan to reduce the cost of maintenance coating and contribute to the service life extension of steel bridges by applying high performance coatings to steel bridges that will be constructed in the future. From the deterioration models based on the field evaluation for chlorinated rubber and urethane topcoat systems, which have been applied often, the mean service lives were derived as 20.8 and 26.6 years, respectively. For the other coating systems that have not been applied in practice, the coordination factors were differentially applied with evaluation items. The most durable coating system was predicted to be thermal spray coating (TSC) primer/epoxy intermediate coat/fluoride resin topcoat, with a predicted value as long as 42.2 years. The LCC analysis indicates that partial application of high performance coating, such as TSC and fluoride resin, to specific parts vulnerable to corrosion and ultraviolet ray (UV) is more advantageous than the use of general coating systems.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.