• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1991년도 추계학술대회 논문집
• /
• pp.73-78
• /
• 1991

In this study of stacked type film chip capacitor, the important parameters are heat-treated temperature, pressure and time. We measured the temperature dependence of dielectric properties and dissipation factor and the frequency dependence of dielectric properties, dissipation factor, ESR(Equivalent Series Resistance) and impedance in stacked type film capacitor. As a result, the best conditions of heat-treated temperature, pressure and time were proved to be 130$^{\circ}C$, 10kg/$\textrm{cm}^2$ and 3hrs, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.891-892
• /
• 2006

An obstacle is an element for power to small and slim the existing portable communication set. Developed Inductor for Chip-type electric power in needs to solve this. Stack applied Process, and used gap of a magnetic path, and made a height of an element to 1.0T or below, and this development commodity did product for saturation prevention to materials of silver. Saturation current characteristic of Chip-type inductor was low compare with winding-type inductors, but bulk against performance were had superior excellence. Chip-type inductor can raise performance per unit volume compared with the existing inductors at these papers. Therefore, acceleration can get growth of small and slim of a mobile product done, and expect.

• 한국세라믹학회지
• /
• 제31권11호
• /
• pp.1355-1361
• /
• 1994

With the availability of ceramics (Al2O3, Al2O3-TiC), it is possible to machine very hard steel at different cutting conditions. When hardened steel STD 11 is turned using ceramic tools, chip formation is observed conical-herical and arc chips with a cyclic saw toothed type. The main cause of saw toothed chip formation is observed conical-herical and arc chips with a cyclic saw toothed type. The main cause of saw toothed chip formation is found to be periodic gross shear fracture extending from the free surface of the chip toward the tool tip. In regard to chip control, ceramic Al2O3 is superior to the other cutting tools. The roughness of machined surface was getting worse with increasing of cutting speed and feed.

• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2664-2675
• /
• 1993

In this paper, the effects of chip breaker configuration on cutting forces for various cutting conditions are investigated and a method for predicting cutting forces effectively for chip breaker insert in milling is described. Based on the shear plane model and the relevant equations already existing for the relation among the parameters, the method makes use of the analytic geometric approach considering the configuration of cutting too by a 3-dimensional coordinate transformation matrix. The groove type chip breaker insert is modeled to be a double rake insert, represented by the first radial rake angle, the second radial rake angle and the length of land, and the program analyzing the cutting forces is developed. The program capability is verified by comparing the results with the experimental ones for a single cutter; and in case of primary cutting forces, the results of simulation and experiments agree very well showing 2%~16.7% difference within the feed rate range investigated.

• 한국정밀공학회지
• /
• 제7권2호
• /
• pp.85-94
• /
• 1990

In automatic metal cuttings, the chip control is one of the serious problems. So the automatic detection of chip forms is essential to the chip control in automatic metal cuttings. Cutting experiments were carried out under the variety of cutting conditions (cutting speed, feed, depth of cut and tool geometry) and with workpiece made of steel (S45C), and cutting forces were measured in-processing by using a piezoelectric type Tool Dynamometer. In this report, the frequency analysis of dynamic components, the upper frequency distributions, the ratio of RMS values, the numbers of null point and the probability density were calculated from the dynamic componeents of cutting forces filtered through various band pass filters. Experimental results showed that computer chip form monitoring system based on the cutting forces was designed and simulated and that 6 type of chip forms could be detected while in-process machining.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.117-123
• /
• 2011

The low electric power and high efficiency chips are required because of the appearance of smart phones. Also, high-capacity memory chips are needed. e-MMC(embedded Multi-Media Card) for this is defined by JEDEC(Joint Electron Device Engineering Council). The e-MMC memory for research and development is a memory mulit-chip module of 64GB using 16-multilayers of 4GB NAND-flash memory. And it has simplified the chip by using SIP technique. But mulit-chip module generates high heat by higher integration. According to the result of study, whenever semiconductor chip is about 10 $^{\circ}C$ higher than the design temperature it makes the life of the chip shorten more than 50%. Therefore, it is required that we solve the problem of heating value and make the efficiency of e-MMC improved. In this study, geometry of 16-multilayered structure is compared the temperature distribution of four different geometries along the numerical analysis. As a result, it is con finned that a multilayer structure of stair type is more efficient than a multilayer structure of vertical type because a multi-layer structure of stair type is about 9 $^{\circ}C$ lower than a multilayer structure of vertical type.

• 한국전기전자재료학회논문지
• /
• 제13권10호
• /
• pp.840-846
• /
• 2000

In this work, small-size, high-performance solenoid-type RF chip inductors utilizing a low-loss Al$_2$O$_3$core material were investigated. The size of the chip inductors fabricated in this work were 15$\times$10$\times$0.7㎣, 2.1$\times$1.5$\times$10㎣, and 2.4$\times$2.0$\times$1.4㎣ and copper (Cu) wire with 40 ㎛ diameter was used as the coils. High frequency characteristics of the inductance, quality factor, and impedance of developed inductors were measured suing an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). It was observed that the developed inductors with the number of turns of 7 have the inductance of 33 to 100nH and exhibit the self-resonant frequency (SRF) of .26 to 1.1 GHz. The SRF of inductors decreases with increasing the inductance and the inductors have the quality factor of 60 to 80 in the frequency range of 300 MHz to 1.1 GHz. In this study, small-size solenoid-type RF chip inductors with high inductance and high quality factor were fabricated successfully. It is suggested that the thin film-type inductor is necessary to fabricate the smaller size inductors at the expence of inductance and quality factor values.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권2호
• /
• pp.330-335
• /
• 2008

In this study, highly miniaturized short-wavelength transmission line employing periodically perforated ground metal (PPGM) structures were developed for application to miniaturized on-chip passive component on Si RFIC. The transmission line employing PPGM structure showed shorter wavelength and lower characteristic impedance than conventional coplanar-type transmission line. The wavelength of the transmission line employing PPGM structure was 57% of the conventional coplanar-type transmission line on Si Radio Frequency Integrated Circuit (RFIC) substrate. Basic characteristics of the transmission line employing PPGM structure were also investigated in order to evaluate its suitability for application to a development of miniaturized passive on-chip components. According to the results, it was found that the PPGM structure is a promising candidate for application to a development of miniaturized on-chip passive components on Si RFIC.

• Journal of Forest and Environmental Science
• /
• 제25권1호
• /
• pp.75-84
• /
• 2009

This study was conducted to investigate the physical properties of wood chip for fuel processing with woody biomass. Seven species are selected and processed for testing physical properties by 3-type wood chippers which are commonly used in Korea. Wood chips produced by self-propelled drum chipper and fixed type wood chipper equipped with separator were uniform in size and shape. It was shown that the bulk density of produced wood chips was decreased with increasing the wood chip layer thickness, and oak chips prepared by self-propelled drum chipper and fixed type wood chipper showed the highest bulk density.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1322-1323
• /
• 2006

This research aims to develop the multiple channel electrochemical DNA chip that has the above characteristic and be able to solve the problems. At first, we fabricated a high integration type DNA chip array by lithography technology. It is able to detect a plural genes electrochemically after immobilization of a plural probe DNA and hybridization of non-labeling target DNA on the electrodes simultaneously.