• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.11 no.1
• /
• pp.64-72
• /
• 2001

This paper is on a design of the high-speed cipher IC using IDEA algorithm. The chip is consists of six functional blocks. The principal blocks are encryption and decryption key generator, input data circuit, encryption processor, output data circuit, operation mode controller. In subkey generator, the design goal is rather decrease of its area than increase of its computation speed. On the other hand, the design of encryption processor is focused on rather increase of its computation speed than decrease of its area. Therefore, the pipeline architecture for repeated processing and the modular multiplier for improving computation speed are adopted. Specially, there are used the carry select adder and modified Booth algorithm to increase its computation speed at modular multiplier. To input the data by 8-bit, 16-bit, 32-bit according to the operation mode, it is designed so that buffer shifts by 8-bit, 16-bit, 32-bit. As a result of simulation by 0.25 $\mu\textrm{m}$ process, this IC has achieved the throughput of 1Gbps in addition to its small area, and used 12,000gates in implementing the algorithm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.12
• /
• pp.1914-1919
• /
• 2021

With the development of advanced industries, research on image processing hardware is essential, and timing verification at the gate level is required for actual chip operation. For FPGA-based verification, DDR3 memory interface was previously applied. But recently, as the FPGA specification has improved, DDR4 memory is used. In this case, when a previously used memory interface is applied, the timing mismatch of signals may occur and thus cannot be used. This is due to the difference in performance between CPU and memory. In this paper, the problem is solved through state optimization of the existing interface system FSM. In this process, data read speed is doubled through AXI Data Width modification. For actual case analysis, ZC706 using DDR3 memory and ZCU106 using DDR4 memory among Xilinx's SoC boards are used.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.321-326
• /
• 2022

In this study, cogeneration power plants that use biomass as a raw material to convert them into energy have recently received a lot of attention worldwide and are gradually increasing in South Korea. Therefore, in order to confirm the possibility of using the generated floor material as a fine aggregate for concrete, properties and stability evaluation experiments were performed. Compared to standard sand, the compressive strength of wood chip aggregate was improved by 11 % to 111 %, the length change rate was 89 %, and the waste processing test results met all criteria for hazardous substances. All of these are satisfied, and it is judged that the floor materials by the cogeneration power plant can be used as a fine aggregate for concrete.

• Smart Media Journal
• /
• v.13 no.3
• /
• pp.36-44
• /
• 2024

Recently, large-scale artificial intelligence (AI) such as ChatGPT have been developed, and as AI is used across various industrial fields, attention is focused on AI chips (semiconductors). AI chips refer to chips designed for calculations for AI algorithms, and many companies at domestic and abroad, such as NVIDIA, Tesla, and ETRI, are developing AI chips. In this paper, we survey research trends on nine types of AI chips. Currently, many attempts have been made to improve the computational performance of most AI chips, and semiconductors for specific purposes are also being designed. In order to compare various AI semiconductors, each chip is analyzed in terms of operation unit, speed, power, and energy efficiency. We introduce currently existing optimization methodologies for AI computation. Based on this, future research directions for AI semiconductors are presented in this paper.

• Horticultural Science & Technology
• /
• v.32 no.2
• /
• pp.171-177
• /
• 2014

In an effort to investigate special distribution of glucose content of potato tuber of a cultivar 'Superior' after harvest, a whole tuber was longitudinally cut into halves and cut-surface was divided into 11 regions. Approximate glucose concentration of each section was determined using a commercial blood glucose meter. Higher level of glucose was detected in the outer layers of tissue than inner part of tuber although there were lower coefficients of variation value, 37.4% and 34.1% among individual tubers and among defined sections, respectively. A positive correlation between the whole tuber and individual section was existed in glucose content, where the central pith tissue gave the highest coefficient (r = 0.921) and bud end tissue did the lowest (r = 0.544). Glucose content of the tubers stored for 4 months at $2.0^{\circ}C$ was 5.5 fold higher compared to the tubers kept in ambient temperature. The chip color of the former tubers was much brighter than those of the latter tubers. The result obtained in the present study suggests that the blood glucose meter can be used to a rapid and simple evaluation of glucose content and therein be applied to estimate the processing quality of potato tubers during postharvest handling.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.5
• /
• pp.24-32
• /
• 2017

In this paper, a low power 4th order delta-sigma modulator was designed with a high resolution of 12 bits or more for the biological signal processing. Using time-interleaving technique, 4th order delta-sigma modulator was designed with one operational amplifier. So power consumption can be reduced to 1/4 than a conventional structure. To operate stably in the big difference between the two capacitor for kT/C noise and chip size, the variable-stage amplifier was designed. In the first phase and second phase, the operational amplifier is operating in a 2-stage. In the third and fourth phase, the operational amplifier is operating in a 1-stage. This was significantly improved the stability of the modulator because the phase margin exists within 60~90deg. The proposed delta-sigma modulator is designed in a standard $0.18{\mu}m$ CMOS n-well 1 poly 6 Metal technology and dissipates the power of $354{\mu}W$ with supply voltage of 1.8V. The ENOB of 11.8bit and SNDR of 72.8dB at 250Hz input frequency and 256kHz sampling frequency. From measurement results FOM1 is calculated to 49.6pJ/step and FOM2 is calculated to 154.5dB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.65-73
• /
• 2003

This paper presents the implementation of an analog signal-processing ASIS to detect an angular velocity signal from a vibrator angular velocity detection sensor. The output of the sensor to be charge appeared as the variation of the capacitance value in the structure of the sensor was detected using charge amplifiers and a self oscillation circuit for driving the sensor was implemented with a sinusoidal self oscillation circuit using the resonance characteristics of the sensor. Specially an automatic gain control circuit was utilized to prevent the deterioration of self-oscillation characteristics due to the external elements such as the characteristic variation of the sensor process and the temperature variation. The angular velocity signal, amplitude-mod)Hated in the operation characteristics of the sensor, was demodulated using a synchronous detection circuit. A switching multiplication circuit was used in the synchronous detection circuit to prevent the magnitude variation of detected signal caused by the amplitude variation of the carrier signal. The ASIC was designed and implemented using 0.5${\mu}{\textrm}{m}$ CMOS process. The chip size was 1.2mm x 1mm. In the experiment under the supply voltage of 3V, the ASIC consumed the supply current of 3.6mA and noise spectrum density from dc to 50Hz was in the range of -95 dBrms/√Hz and -100 dBrms/√Hz when the ASIC, coupled with the sensor, was in normal operation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.3
• /
• pp.187-187
• /
• 2004

In this paper, we present an efficient architecture of a versatile Reed-Solomon (RS) decoder which can be programmed to decode RS codes continuously with my message length k as well as any block length n. This unique feature eliminates the need of inserting zeros for decoding shortened RS codes. Also, the values of the parameters n and k, hence the error-correcting capability t can be altered at every codeword block. The decoder permits 3-step pipelined processing based on the modified Euclid's algorithm (MEA). Since each step can be driven by a separate clock, the decoder can operate just as 2-step pipeline processing by employing the faster clock in step 2 and/or step 3. Also, the decoder can be used even in the case that the input clock is different from the output clock. Each step is designed to have a structure suitable for decoding RS codes with varying block length. A new architecture for the MEA is designed for variable values of the t. The operating length of the shift registers in the MEA block is shortened by one, and it can be varied according to the different values of the t. To maintain the throughput rate with less circuitry, the MEA block uses both the recursive technique and the over-clocking technique. The decoder can decodes codeword received not only in a burst mode, but also in a continuous mode. It can be used in a wide range of applications because of its versatility. The adaptive RS decoder over GF($2^8$) having the error-correcting capability of upto 10 has been designed in VHDL, and successfully synthesized in an FPGA chip.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.3
• /
• pp.29-38
• /
• 2004

In this paper, we present an efficient architecture of a versatile Reed-Solomon (RS) decoder which can be programmed to decode RS codes continuously with my message length k as well as any block length n. This unique feature eliminates the need of inserting zeros for decoding shortened RS codes. Also, the values of the parameters n and k, hence the error-correcting capability t can be altered at every codeword block. The decoder permits 3-step pipelined processing based on the modified Euclid's algorithm (MEA). Since each step can be driven by a separate clock, the decoder can operate just as 2-step pipeline processing by employing the faster clock in step 2 and/or step 3. Also, the decoder can be used even in the case that the input clock is different from the output clock. Each step is designed to have a structure suitable for decoding RS codes with varying block length. A new architecture for the MEA is designed for variable values of the t. The operating length of the shift registers in the MEA block is shortened by one, and it can be varied according to the different values of the t. To maintain the throughput rate with less circuitry, the MEA block uses both the recursive technique and the over-clocking technique. The decoder can decodes codeword received not only in a burst mode, but also in a continuous mode. It can be used in a wide range of applications because of its versatility. The adaptive RS decoder over GF(2$^{8}$ ) having the error-correcting capability of upto 10 has been designed in VHDL, and successfully synthesized in an FPGA chip.

• Journal of the Institute of Convergence Signal Processing
• /
• v.15 no.2
• /
• pp.70-75
• /
• 2014

Recently, the demand for high-integrated, low-powered, and high-powered SoC design has been increasing due to the multi-functionality and the miniaturization of digital devices and the high capacity of service informations. With the rapid evolution of the system, the required hardware performances have become diversified, the FPGA system has been increasingly adopted for the rapid verification, and SoC system using the FPGA and the ARM core for control has been growingly chosen. While the AXI bus is used in these kinds of systems in various ways, it is traditionally designed with AXI slave structure. In slave structure, there are problems with the CPU resources because CPU is continually involved in the data transfer and can't be used in other jobs, and with the decreased transmission efficiency because the time not used of AXI bus beomes longer. In this paper, an efficient AXI master interface is proposed to solve this problem. The simulation results show that the proposed system achieves reductions in the consumption clock by an average of 51.99% and in the slice by 31% and that the maximum operating frequency is increased to 107.84MHz by about 140%.