• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.3
• /
• pp.53-58
• /
• 2008

In this study, we fabricated embedded IC (Double Pole Double throw switch chip) polymer substrate and evaluate it for 2.4 GHz WiFi application. The switch chips were laminated using FR4 and ABF(Ajinomoto build up film) as dielectric layer. The embedded DPDT chip substrate were interconnected by laser via and Cu pattern plating process. DSC(Differenntial Scanning Calorimetry) analysis and SEM image was employed to calculate the amount of curing and examine surface roughness for optimization of chip embedding process. ABF showed maximum peel strength with Cu layer when the procuring was $80\sim90%$ completed and DPDT chip was laminated in a polymer substrate without void. An embedded chip substrate and wire-bonded chip on substrate were designed and fabricated. The characteristics of two modules were measured by s-parameters (S11; return loss and S21; insertion loss). Insertion loss is less than 0.55 dB in two presented embedded chip board and wire-bonded chip board. Return loss of an embedded chip board is better than 25 dB up to 6 GHz frequency range, whereas return loss of wire-bonding chip board is worse than 20 dB above 2.4 GHz frequency.

• Journal of electromagnetic engineering and science
• /
• v.14 no.1
• /
• pp.43-45
• /
• 2014

We propose a printed circuit board (PCB)-embedded antenna for millimeter-wave chip-to-chip communication. The antenna is 0.18 mm in height which is 1/20 wavelength at 80 GHz. In order to realize such a low profile, a zeroth-order resonator antenna with a periodic array of four unit cells is employed, and its geometry is optimized to cover an 8-GHz bandwidth from 76 to 84 GHz. With this;the antenna is capable of radiating in a direction parallel to the board length despite the short distance between the ground and the radiator. Simulation and measurement results show that the optimized design has low reflection coefficients and consistent radiation patterns throughout the target bandwidth.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.17 no.6
• /
• pp.375-382
• /
• 2022

This paper proposes a multi-core cooperative computing structure considering the heterogeneous features of automotive embedded on-chip software. The automotive embedded software has the heterogeneous execution flow properties for various hardware drives. Software developed with a homogeneous execution flow without considering these properties will incur inefficient overhead due to core latency and load. The proposed method was evaluated on an target board on which a automotive MCU (micro-controller unit) with built-in multi-cores was mounted. We demonstrate an overhead reduction when software including common embedded system tasks, such as ADC sampling, DSP operations, and communication interfaces, are implemented in a heterogeneous execution flow. When we used the proposed method, embedded software was able to take advantage of idle states that occur between heterogeneous tasks to make efficient use of the resources on the board. As a result of the experiments, the power consumption of the board decreased by 42.11% compared to the baseline. Furthermore, the time required to process the same amount of sampling data was reduced by 27.09%. Experimental results validate the efficiency of the proposed multi-core cooperative heterogeneous embedded software execution technique.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.9
• /
• pp.1615-1620
• /
• 2010

A thin film thermoelectric cooler for COB direct assembly was proposed and the COB cooler structure was modeled by electrical equivalent circuit by using SPICE model of thermoelectric devices. The embedded cooler attached between the die chip and metal plate can offer the possibility of thin film active cooling for the COB direct assembly. We proposed a driving method of TEC by using pulse width modulation technique. The optimum power to the TEC is simulated by using a SPICE model of thermoelectric device and passive components representing thermal resistance and capacitance. The measured and simulated results offer the possibility of thin film active cooling for the COB direct assembly.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.45.4-45
• /
• 2001

In this paper, we present the wet-based monitoring system for industrial controller such as inverter controller for hydraulic elevators. The monitoring system is using an embedded web server on embedded Linux platform. The control board of system-On-Chip (SoC) is based on ARM7TDMI with Ethernet controller. Wet-based monitoring system using embedded Linux platform can reduce the cost, and have flexibility both of technical issues and locations If the system to be monitored. The system shows the feasibility of remote monitoring system based on embedded Linux platform.

• ETRI Journal
• /
• v.31 no.6
• /
• pp.732-740
• /
• 2009

This paper describes the implementation of a digital audio effect system-on-a-chip (SoC), which integrates an embedded digital signal processor (DSP) core, audio codec intellectual property, a number of peripheral blocks, and various audio effect algorithms. The audio effect SoC is developed using a software and hardware co-design method. In the design of the SoC, the embedded DSP and some dedicated hardware blocks are developed as a hardware design, while the audio effect algorithms are realized using a software centric method. Most of the audio effect algorithms are implemented using a C code with primitive functions that run on the embedded DSP, while the equalization effect, which requires a large amount of computation, is implemented using a dedicated hardware block with high flexibility. For the optimized implementation of audio effects, we exploit the primitive functions of the embedded DSP compiler, which is a very efficient way to reduce the code size and computation. The audio effect SoC was fabricated using a 0.18 ${\mu}m$ CMOS process and evaluated successfully on a real-time test board.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.975-976
• /
• 1993

This talk presents the overview of the author's research and development activities on fuzzy inference hardware. We involved it with two distinct approaches. The first approach is to use application specific integrated circuits (ASIC) technology. The fuzzy inference method is directly implemented in silicon. The second approach, which is in its preliminary stage, is to use more conventional microprocessor architecture. Here, we use a quantitative technique used by designer of reduced instruction set computer (RISC) to modify an architecture of a microprocessor. In the ASIC approach, we implemented the most widely used fuzzy inference mechanism directly on silicon. The mechanism is beaded on a max-min compositional rule of inference, and Mandami's method of fuzzy implication. The two VLSI fuzzy inference chips are designed, fabricated, and fully tested. Both used a full-custom CMOS technology. The second and more claborate chip was designed at the University of North Carolina(U C) in cooperation with MCNC. Both VLSI chips had muliple datapaths for rule digital fuzzy inference chips had multiple datapaths for rule evaluation, and they executed multiple fuzzy if-then rules in parallel. The AT & T chip is the first digital fuzzy inference chip in the world. It ran with a 20 MHz clock cycle and achieved an approximately 80.000 Fuzzy Logical inferences Per Second (FLIPS). It stored and executed 16 fuzzy if-then rules. Since it was designed as a proof of concept prototype chip, it had minimal amount of peripheral logic for system integration. UNC/MCNC chip consists of 688,131 transistors of which 476,160 are used for RAM memory. It ran with a 10 MHz clock cycle. The chip has a 3-staged pipeline and initiates a computation of new inference every 64 cycle. This chip achieved an approximately 160,000 FLIPS. The new architecture have the following important improvements from the AT & T chip: Programmable rule set memory (RAM). On-chip fuzzification operation by a table lookup method. On-chip defuzzification operation by a centroid method. Reconfigurable architecture for processing two rule formats. RAM/datapath redundancy for higher yield It can store and execute 51 if-then rule of the following format: IF A and B and C and D Then Do E, and Then Do F. With this format, the chip takes four inputs and produces two outputs. By software reconfiguration, it can store and execute 102 if-then rules of the following simpler format using the same datapath: IF A and B Then Do E. With this format the chip takes two inputs and produces one outputs. We have built two VME-bus board systems based on this chip for Oak Ridge National Laboratory (ORNL). The board is now installed in a robot at ORNL. Researchers uses this board for experiment in autonomous robot navigation. The Fuzzy Logic system board places the Fuzzy chip into a VMEbus environment. High level C language functions hide the operational details of the board from the applications programme . The programmer treats rule memories and fuzzification function memories as local structures passed as parameters to the C functions. ASIC fuzzy inference hardware is extremely fast, but they are limited in generality. Many aspects of the design are limited or fixed. We have proposed to designing a are limited or fixed. We have proposed to designing a fuzzy information processor as an application specific processor using a quantitative approach. The quantitative approach was developed by RISC designers. In effect, we are interested in evaluating the effectiveness of a specialized RISC processor for fuzzy information processing. As the first step, we measured the possible speed-up of a fuzzy inference program based on if-then rules by an introduction of specialized instructions, i.e., min and max instructions. The minimum and maximum operations are heavily used in fuzzy logic applications as fuzzy intersection and union. We performed measurements using a MIPS R3000 as a base micropro essor. The initial result is encouraging. We can achieve as high as a 2.5 increase in inference speed if the R3000 had min and max instructions. Also, they are useful for speeding up other fuzzy operations such as bounded product and bounded sum. The embedded processor's main task is to control some device or process. It usually runs a single or a embedded processer to create an embedded processor for fuzzy control is very effective. Table I shows the measured speed of the inference by a MIPS R3000 microprocessor, a fictitious MIPS R3000 microprocessor with min and max instructions, and a UNC/MCNC ASIC fuzzy inference chip. The software that used on microprocessors is a simulator of the ASIC chip. The first row is the computation time in seconds of 6000 inferences using 51 rules where each fuzzy set is represented by an array of 64 elements. The second row is the time required to perform a single inference. The last row is the fuzzy logical inferences per second (FLIPS) measured for ach device. There is a large gap in run time between the ASIC and software approaches even if we resort to a specialized fuzzy microprocessor. As for design time and cost, these two approaches represent two extremes. An ASIC approach is extremely expensive. It is, therefore, an important research topic to design a specialized computing architecture for fuzzy applications that falls between these two extremes both in run time and design time/cost. TABLEI INFERENCE TIME BY 51 RULES {{{{Time }}{{MIPS R3000 }}{{ASIC }}{{Regular }}{{With min/mix }}{{6000 inference 1 inference FLIPS }}{{125s 20.8ms 48 }}{{49s 8.2ms 122 }}{{0.0038s 6.4㎲ 156,250 }} }}

• Journal of Korea Multimedia Society
• /
• v.4 no.6
• /
• pp.570-578
• /
• 2001

Boundary scan architecture test methodology was introduced to facilitate the testing of complex printed circuit board. The boundary scan architecture has a tremendous potential for real time monitoring of the operational status of a system without interference of normal system operation. In this paper, a new type of embedded controller for real time monitoring of the operational status of a system is proposed and designed by using boundary scan architecture. The proposed real time monitoring embedded controller consists of test access port controller and an embedded controller proposed real time monitoring embedded controller using boundary scan architecture can save the hard-wire resource and can easily interface with boundary scan architecture chip. Experimental results show that the real time monitoring using proposed embedded controller is more effective then the real time monitoring using host computer.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.3
• /
• pp.77-82
• /
• 2012

In this paper, the research of IC embedded PCB process is carried out. For embedding chips into PCB, solder-balls on chips were etched out and ABF(Ajinomoto Build-ip Film), prepreg and Cu foil was laminated on that to fabricate 6 layer build-up board. The chip of which solder ball was removed was successfully interconnected with PCB by laser drilling and Cu plating. However, de-lamination phenomenon occurred between chip surface and ABF during reflow and thermal shock. To solve this problem, de-smear and plasma treatment was applied to PI(polyimide) passivation layer on chip surface to improve the surface roughness. The properties of chip surface(PI) was investigated in terms of AFM(Atomic Force Micrometer), SEM and XPS (X-ray Photoelectron Spectroscopy). As results, nano-size anchor was evenly formed on PI surface when plasma treatment was combined with de-smear(NaOH+KMnO4) process and it improved thermal shock reliability ($260^{\circ}C$-10sec solder floating).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.1
• /
• pp.75-79
• /
• 2013

Demands for semiconductor devices are dramatically increasing, and advancements in fabrication technology are allowing a step-up in the number of devices per unit area. As a result, semiconductor devices require higher heat dissipation, and thus, cooling solutions have become important for guaranteeing their operational reliability. In particular, in chip-in-board packages, in which chips and passives are embedded in the substrates for efficient device layout, heat dissipation is of greater importance. In this study, a thermal model for layers of different materials has been proposed, and then, the heat transfer has been simulated by imposing a set of appropriate boundary conditions. Heat generation can be predicted based on the results, which will be utilized as practical data for actual package design.