• Geomechanics and Engineering
• /
• v.16 no.4
• /
• pp.375-384
• /
• 2018

Unconfined compressive strength (UCS) of high plasticity clayey soil mixed with 5 and 10 % of Portland cement and four chemical agents such as sodium hexametaphosphate, aluminum sulfate, sodium carbonate, and sodium silicate with 0, 5, 10, and 20% concentrations was comparatively evaluated. The individual and combined effects of the cement and chemical agents on the UCS of the soil mixture were investigated. The strength of the soil-cement mixture generally increases with increasing the cement content. However, if the chemical agent is added to the mixture, the strength of the cement-chemical agent-soil mixture tends to vary depending on the type and the amount of the chemical agent. At low concentrations of 5% of aluminum sulfate and 5% and 10% of sodium carbonate, the average UCS of the cement-chemical agent-soil mixture slightly increased compared to pure clay due to increasing the flocculation of the clay in the mixture. However, at high concentrations (20%) of all chemical agents, the UCS significantly decreased compared to the pure clay and clay-cement mixtures. In the case of high cement content, the rate of UCS reduction is the highest among all cement-chemical agent-soil mixtures, which is more than three times higher in comparison to the soil-chemical agent mixtures without cement. Therefore, in the mixture with high cement (> 10%), the reduction of the USC is very sensitive when the chemical agent is added.

• 제어로봇시스템학회:학술대회논문집
• /
• 1995.10a
• /
• pp.328-331
• /
• 1995

A successful, computer-aided design support system can help a process designer focus on making effective design decisions, not merely tedious routine calculations. Such a system is essential to enhance quality of design in terms of economics, environmental benignity, reliability, robustness, and operability. Such a statement is even more accepted when applied to conceptual design problems, where gross design specifications are given while a combinatorial number of design alternatives exists. This paper presents an agent-based approach as a systematic and efficient way to design a design support system for the synthesis of conceptual chemical processes. An agent-based approach allows us to handle design knowledge as an object and thus greatly improve the modularity and reusability of that knowledge. Such modularity and reusability lead to the increased productivity in the development of a design support system and the increased ease in the relaxation of design decisions and the generation of design alternatives, both of which functions are critically important in dealing with the complexity and uncertainty of conceptual design problems.

• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.369-375
• /
• 2008

To achieve zero-emission, one of the main goals of an eco-industrial park (EIP), it is needed to develop an effective water exchange network. The network includes various subsystems and decision making processes, which make the modeling process extremely complicated. Agent-based modeling was used to simulate water exchange network in an EIP. Firm agents were created based on the behavior pattern of firms, and an agent-based model (ABM) was made with the agents, showing the growth of the exchange network. An existing steel and iron making industrial park was chosen as a case study, and the ABM model shows eco-efficient behavior with a decreased environmental cost. Water reuse network based on the ABM model results in 35% decrease of the fresh water supply and 50% reduction of the wastewater generation in EIP. A case study shows that agent-based model can be a powerful tool in modeling and designing complex eco-industrial parks, especially when a part of the system needs to be changed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.215-222
• /
• 2004

We synthesized a aziridine bonding agent that play an important role in increasing the adhesion property between polymer binders and solid particles. It increases the physical properties of polymer-based propellant. Chemical reaction between two materials increase the interface adhesion. We analyzed and studied the chemical characteristics of the material and physical properties of a liner applied the aziridine bonding agent. We also studied the adhesion property of a liner/propellant applied the aziridine bonding agent. 3M was use as control group. In accordance with US MIS (Missile Interim Specification) we examined the chemical properties. As a result of our study, newly synthesized aziridine bonding agent was as good as quality of 3M HX-868.

• Applied Chemistry for Engineering
• /
• v.31 no.2
• /
• pp.230-236
• /
• 2020

In this study, an adhesive tape with water and impact resistance for mobile devices was developed using a UV-curable urethane acrylate based polymer as a substrate. The substrate fabricated by UV-curable materials shows hydrophobicity and poor wettability, which significantly deteriorates the interface-adhesions between the substrate and acrylic adhesive. In order to improve the interface adhesion, 3-glycidoxy-propyl trimethoxysilane (GPTMS), a silane coupling agent having epoxy functional groups, was selected and incorporated into UV-curable urethane acrylate based polymer resins in various contents. The changes of the chemical composition according to the contents of GPTMS was studied with Fourier-transform infrared spectroscopy (FT-IR), energy-dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) to know the surface bonding properties. Also mechanical properties of the substrate were characterized by tensile strength, gel fraction and water contact angle measurements. The peel strengths at 180° and 90° were measured to compare the adhesion between the substrate and adhesive according to the silane coupling agent contents. The mechanical strength of the urethane acrylate adhesive tape decreased as the silane coupling agent increased, but the adhesion between the substrate and adhesives increased remarkably at an appropriate content of 0.5~1 wt%.

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.339-346
• /
• 2020

We functionalized a wear-resistant carbon-based MoS2 filler to solve its limited wear condition problem. The filler exhibits excellent lubricative properties. The surface modification of MoS2 was carried out using a (3-glycidyloxypropyl)trimethoxysilane (GPTMS) silane coupling agent to improve the low compatibility and dispersibility of the filler that generally degrade the performance of composites. A silane coupling agent was employed for the functionalization of MoS2, and its effect on the wear resistance of MoS2/Polyamide-6,6 was investigated. The silanization of MoS2 was identified by contact angle analysis and Fourier-transform infrared, energy dispersive X-ray, and X-ray photoelectron spectroscopies. The wear resistance of the composite was found to be improved significantly by the surface functionalization of MoS2.

• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.348-351
• /
• 2011

In this research, we developed a sensor system which can easily detect several chelating agents using polydiacetylene(PDA) vesicles. In comparison to other sensors, PDA based sensor has several advantages. First, detection method is much simpler and faster because it does not require any labeling step in the experiment procedure. Second, significant color-transition from blue to red based upon external stimulus allows us the detection by naked eyes. Finally, it is also possible to perform quantitative analysis of the concentration of the chelating agent by measuring the colorimetric response. In this paper, five types of chelating agents were used, including EDTA, EGTA, NTA, DCTA and DTPA. Among them, EDTA and DCTA triggered especially strong color-transition. In conclusion, this study has led to a successful development of a color transition-based PDA sensor system for easy and rapid detection of chelating agents.

• Resources Recycling
• /
• v.30 no.3
• /
• pp.41-46
• /
• 2021

Methanesulfonic acid (MSA) can be considered effective in the leaching of metals because of its advantageous physical and chemical properties. The chemical reactivities of MSA and sulfuric acid were compared based on their structures and the dissolution data of Co and Ni metal. The inductive and resonance effects play a vital role in the chemical reactivities of these two acids. The dissolution percentages of Co and Ni in the sulfuric acid solution were higher than those in the MSA solution under the same experimental conditions. Considering the strong acidity of MSA and the high solubility of its metal salts, MSA can be employed as a leaching agent for the recovery of metals.

• Applied Chemistry for Engineering
• /
• v.19 no.6
• /
• pp.668-673
• /
• 2008

The objective of this study is to optimize the leaching conditions of sequential leaching and extracting processes for selective Ni recovery from spent Ni-Mo-based catalyst. The selective Ni recovery process consists of two processes of leaching and extracting process. In this 2-step process, Ni component is dissolved from solid spent Ni-Mo-based catalyst into leaching agent in leaching process and sequentially extracted to Ni complex with an extracting agent in the extracting process. The solutions of nitric acid ($HNO_3$), ammonium carbonate ($(NH_4)_2CO_3$) and sodium carbonate ($Na_2CO_3$) were used as a leaching agent in leaching process and oxalic acid was used as an extracting agent in extracting process. $HNO_3$ solution is the most efficient leaching agent among the various leaching agent. Also, the optimized leaching conditions for the efficient and selective Ni recovery were the leaching temperature of $90^{\circ}C,\;HNO_3$ concentration of 6.25 vol% and elapsed time of 3 h. As a result, Nickel oxalate having the highest yield of 88.7% and purity of 100% was obtained after sequentially leaching and extracting processes under the optimized leaching conditions.

• Journal of the Korea Institute of Building Construction
• /
• v.8 no.1
• /
• pp.91-96
• /
• 2008

This study is to investigate the influence of the over-added chemical agents, such as water reducing agent(WRA) and AE water reducing agent(AEWRA), on the physical properties of concrete to estimate the degree of damage due to over-added chemical agents. For the fresh concrete, slump and slump flow increased with the increase of WRA and AEWRA as expected. Material segregation phenomenon was observed with the over dosage of lignin based AEWRA about 4 times larger than recommended dosage. The over dosage of AE water reducing agent about 4 times larger than recommended dosage resulted in an increase of air contents remarkably. The set retardation occurred greatly with the increase of AEWRA and WRA. For the properties of the hardened concrete corresponding to the over dosage of AEWRA, it is found that compressive strength of over added AEWRA and WRA concrete are much smaller than those of base and recommended dosage concrete proportionally due to associated increasing air content.