• Journal of Soil and Groundwater Environment
• /
• v.15 no.1
• /
• pp.57-65
• /
• 2010

Currently, the pursuit of industrialization for rapid economic growth has led to serious environmental damage and related problems because of comtamination with chemicals. Over time, this contaminaion is getting worse and worse. Most developing countries have tried to pursue their economic development and growth, however without preparation for the control and disposal of hazardous wastes. Permitting hazardous waste to be abandoned and disposed in appropriately causes soil pollution, groundwater contamination, and surface water contamination, which are all extremely serious. In particular, when hazardous wastes which include toxic chemicals are distributed around the living environment even in small amounts, concentration can occur in the food chain through ecological systems, which can therefore affect human. Chromium(VI) has contaminated soil in China. We experimented to test the immobilization, chemical reduction, and soil washing methods in order to make our experiment efficient in the purification of soil contaminated with Chromium(VI), and to prove the theoretical models by experiments testing the field applications. The field experiment showed that result of experiment satisfied with the standards of China. The result of multi-stage continuous remediation reduce the Chromium(VI) concentration to 11.95 mg/kg and 14.83 mg/kg that were equivalent to 98% and 97% removal rates. This result implied we could apply multi-stage process of Chromium(VI) contaminated soil to meet the regulatory limit of Chromium(VI).

• Journal of Conservation Science
• /
• v.22
• /
• pp.99-108
• /
• 2008

This research aimed to provide a scientific methodology for removing white and black/brown coloured stains on the wall paintings of tombs of Jinpari No 1 and No 4. in the Democratic People's Republic of Korea. For the analysis of chemical composition of stains of the samples from the wall paintings, a microscope and SEM/EDX were used. The analysis confirmed that the fomula of white coloured stains should be $CaSO_4$ or $CaCO_3$ and the black/brown coloured stains should be $CaSO_4$ or $CaCO_3$ with soil deposition. Because of the difficulties of testing several cleaning solutions on sample patches of large area of the painting, the author considered a risk-free cleaning solution as being the most appropriate one, with Ammonium bicarbonate and Anion exchange resin showing satisfactory cleaning effect without visible side effects. For the removal of dense layer of stains, the research suggested that physical cleaning should be followed by applying a cleaning solution.

• International Journal of Concrete Structures and Materials
• /
• v.7 no.3
• /
• pp.225-238
• /
• 2013

In this study, a two-layer feed-forward neural network was constructed and applied to determine a mapping associating mix design and testing factors of cement-nano silica (NS)-rice husk ash ternary blended concrete samples with their performance in conductance to the water absorption properties. To generate data for the neural network model (NNM), a total of 174 field cores from 58 different mixes at three ages were tested in the laboratory for each of percentage, velocity and coefficient of water absorption and mix volumetric properties. The significant factors (six items) that affect the permeability properties of ternary blended concrete were identified by experimental studies which were: (1) percentage of cement; (2) content of rice husk ash; (3) percentage of 15 nm of $SiO_2$ particles; (4) content of NS particles with average size of 80 nm; (5) effect of curing medium and (6) curing time. The mentioned significant factors were then used to define the domain of a neural network which was trained based on the Levenberg-Marquardt back propagation algorithm using Matlab software. Excellent agreement was observed between simulation and laboratory data. It is believed that the novel developed NNM with three outputs will be a useful tool in the study of the permeability properties of ternary blended concrete and its maintenance.

• Biomolecules & Therapeutics
• /
• v.19 no.3
• /
• pp.342-347
• /
• 2011

In the present study, the anticonvulsant effects of Artemisia capillaris Herba (AC) and its major constituent, esculetin (ECT), were tested and the mechanism studied. Locomotion, Myorelaxation, motor coordination and electroshock seizure experiment were conducted in mice. To identify the anticonvulsant mechanism effect of this drug, chemical-induced seizure in mice and the ionic movement in neuroblastoma cells were also observed. The ethanol extract of AC was orally administered to mice 30 min. prior to testing and ECT was intraperitoneally injected. AC and ECT treatment did not change locomotor activities as well as activities on the rota-rod, which indicates that they did not cause a sedative and myorelaxation effect. AC and ECT treatment increased threshold of convulsion induced by electroshock. AC treatment also inhibited convulsion induced by pentylenetetrazole. In the case of strychnine however, only high dose of AC treatment inhibited convulsion. AC and ECT treatment increased the $Cl^-$ influx into the intracellular area in a dose-dependent manner. On the other hand, bicuculline, a GABA antagonist, inhibited the $Cl^-$ influx induced by AC and ECT. These results indicate that ECT induces the anticonvulsive effect of AC extract through the GABAergic neuron.

• Journal of Soil and Groundwater Environment
• /
• v.21 no.6
• /
• pp.169-178
• /
• 2016

The Standards, Measurement and Testing Programme (SM&T-formerly BCR) extraction procedure was applied to fractionate Cr, Cu, Ni, Pb and Zn in 23 top soil samples into: (i) exchangeable phase; (ii) reducible phase; (iii) oxidisable(sulfides and organics bound) phase; and (iv) residual phase. Fractions of Cr and Ni were in the order of residual > oxidisable > reducible > exchangeable phase. The oxidisable phase was identified as dominant for Cu and Pb. Zn had the highest ratio of exchangeable phase in comparision to the other metals. The bioavailability and mobility were assessed to be the greatest for Zn, followed by a decreasing order of Pb, Cu, Ni and Cr. All metal average concentrations in topsoil samples was higher in industrial sites than in agricultural sites. Our results revealed higher concentrations in topsoil samples (0~15 cm) than in sub soils (15~30 cm, 30~60 cm) for most metals at six sites (No. 5, 6, 17, 19, 20, 23). The fractions of exchangeable, reducible ad oxidisable phases showed relatively high correlation with soil pH, Fe/Mn oxide concentrations and organic matter contents, respectively.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.296-300
• /
• 2004

Currently. the study on structural ceramic helps to suggest the precise data of friction and wear in accordance with the various conditions in operations. Also, the study helps to predict effective operating conditions by monitoring the occurrence of wear transition. The studies in the Past were mainly concentrated in using identical materials. However, it is highly likely to have unqualified data from the differences of mechanical and chemical properties between ceramic materials. Thus, in this study, through conducting the ball-on-disk type wear testing, the different ceramic materials has been used to consider tribological characteristics between different ceramic materials. We conducted the wear test by using three kinds of specimen which are zirconia, alumina and silicon carbide against zirconia. We have changed the sliding velocity and the loading conditions in this test and found out that there is row friction coefficient and wear rate in the combination of zirconia and silicon carbide.

• Tribology and Lubricants
• /
• v.33 no.4
• /
• pp.127-133
• /
• 2017

In order to characterize the adhesive properties and failure mechanisms of diamond-like carbon (DLC) films of two different thicknesses (130 nm and $1.2{\mu}m$), deposited by plasma-enhanced chemical vapor deposition on a Si substrate, scratch testing with a micro-indenter ($12.5{\mu}m$ tip radius) was performed under a linearly increasing load. These scratch tests were conducted under the same test conditions for both films. The critical load of each film was estimated from the scratch test results, based on a sharp increase in the coefficient of friction and a clear distinction of failure modes. The critical load was the basis for evaluating the adhesion strength of the films, and the $1.2{\mu}m-thick$ DLC film had superior adhesion strength. For better understanding of the failure modes, the following analyses were conducted: friction behavior and scratch tracks analysis using scanning electron microscopy, energy-dispersive spectroscopy, and 3-D profilometry. The scratch test results showed that failure modes were related to the thickness of the films. The 130 nm-thick DLC film underwent cohesive failure modes (cracks and chipping) before reaching to a gross failure stage. On the other hand, the thicker DLC film ($1.2{\mu}m-thick$) did not exhibit micro cracks before a sudden gross failure of the film together with the evidence of cracking and chipping of the Si substrate.

• Toxicological Research
• /
• v.17
• /
• pp.167-171
• /
• 2001

The introduction of genetically modified crops has raised concerns regarding safety issues over the insertion of foreign genes into plant genomes using recombinant DNA technology. Since 1991 in Japan, 29 foods and 6 food additives have been evaluated, based on the "Guideline for Safety Assessment", before these foods were marketed. The MHW, however, decided that safety assessment of such foods and food additives should be legally imposed. because soon such foods and food additives are expected to circulate globally and a new system for assessing safety of such foods and food additives at a pre-market stage is necessary, in order to avoid the distribution of any genetically modified foods that have had no safety assessment. The MHW published relevant announcements to amend existing regulations on 1 May 2000. "Standards for safety assessment of seed plant" is established based on a concept of substantial equivalence, and applicable to the products which are regarded as equivalent to the existing products used as foods and food additives. The characterization of the food products entails consideration of the molecular characterization. phenotypic and compositional characteristics, key nutrients and toxicants, and toxicity and allergenicity of the introduced proteins, and if there are indications of unintended effects of the modification, whether further safety testing (animal studies etc.) is needed should be considered. Safety and wholesomeness studies with whole foods should be care fully designed in order to avoid nutritional imbalances causing artifacts and uninterpretable results as was the case of Dr. Pusztaiis report. A case study of genetically modified soybeans (glyphosate-tolerant soybeans) on the immune system of rats and mice is shown. Chemical compositions were also compared with those of the non-GM soybeans. The studies failed to detect any differences in immuno-toxic activity.muno-toxic activity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.94-94
• /
• 2013

The Cr-Zr-N films have much improved mechanical properties and very smooth surface roughness. However, in spite of their outstanding properties, the Cr-Zr-N coatings revealed their mechanical properties deteriorated severely with increasing Zr content at $500^{\circ}C$ ecause of very rapid oxidation. Recently oxynitride films have been widely studied due to their excellent unique mechanical properties and oxidation resistance. In this work, CrZr-O-N films with various O contents were synthesized by unbalanced magnetron sputtering with Cr-Zr segment targets (Cr:Zr volume ratios is 1：1) and all films were prepared in a nitrogen rich mixture of N2 and O2. Characteristics such as crystalline structure, hardness and chemical composition as a function of the O content were investigated by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), microhardness testing system and energy dispersive spectroscopy (EDS). Results showed that the thin films had dense and compact microstructure as O content in the films increases. The microstructure of the thin films consisted of mainly crystalline Cr (Zr)N phase and Cr2O3 phase. The maximum hardness and elastic modulus of the films was measured to be approximately 33.2 GPa and 280.6 GPa from the films with low content of O elements. Detailed experimental results will be presented.

• Journal of Korean society of Dental Hygiene
• /
• v.1 no.2
• /
• pp.171-180
• /
• 2001

The purpose of this study was to compared with the properties of commercial polyvinyl siloxane impression materials on the Korean product and the other country one. The materials used in this study were 5 hydrophilic polvinyly siloxane impression materials of light body automixing type (Perfect-F, Handae Chemical, Korea; Examix, GC, Japan; Contrast, VOCO, Germany; Express, 3M, U.S.A; Extrude, Kerr, U.S.A.). Specimens of each impression material were fabricated from a mold with dimensions identical to that specified in ASTM D624-91 and were subjected to tensile lode at 500 mm/min until failure for tear strength. Properties of consistency, strain in compression, recovery from deformation, detail reproduction and linear dimensional change were tested according to the testing methods of the ISO specification no.4823(1992). From this study, the follow ing results were obtained 1. The tear strength values were high ET(3.4kN/m), EP(3.4kN/m), PF(3.0kN/m), CT(3.0kN/m), but the lowest was EM(2.2kN/m)(p<0.05). 2. In the consistency, CT(47 mm) had the highest value, followed by PF(42.1 mm), ET(41.2 mm), and EM(39.6 mm), EP(39.2 mm)(p<0.05). It means more flow that the consistency value is high. 3. The strain in compression values were high followed by EM(5.8%), PF(52%), CT(4.6%), ET(4.1%), EP(2.9%)(p<0.05). 4. In the recovery from deformation, ET(99.95%) and PF(99.90%) had the highest value, followed by EP(99.75%), EM(99.74%) without statistical signification, CT(99.64%) had the lowest value(p<0.05). 5. Detail reproduction reappeared to line $20{\mu}m$ all products. 6. The linear dimensional change was a little shrinked all products. and there were not statistical signification (p>0.05). All products were satisfied the ISO specification.