• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.1-10
• /
• 2022

This paper reviews the principles, advantages, and disadvantages of main explosives detection technologies, as well as research areas needed in the future. Explosives detection technology can be classified into spectroscopic methods, sensor techniques, and olfactory type sensors. There have been advances in explosives detection technology, however studies on discriminatory, portability, and sensitivity for explosives detection still remained competitive.

• Toxicological Research
• /
• v.21 no.4
• /
• pp.271-278
• /
• 2005

Reproductive and developmental toxicology is concerned with various physical or chemical agents interfering with fertility in both gender or normal growth of offsprings. Reproductive and developmental toxicology is rather a complex science, with many fields, i.e., various endpoints are involved and many different mechanisms of action. For that reason, diverse aspects must be considered when attempting to assess possible adverse health effects in the area of reproductive and developmental toxicology. The thalidomide tragedy made it clear to regulatory authorities around the world that systematic, comprehensive evaluation of the reproductive cycle was needed to adequately evaluate the potential of medicinal drugs to impair the process of reproduction or the development of embryos, fetuses, and children. International Conference on Harmonization of Technical Requirements for the Registration of Pharmaceuticals for Human Use (ICH) and U.S. Food and Drug Administration (FDA) developed a guideline to assess the reproductive and developmental toxicity. Also these guidelines have since been applied to the detection and regulation of environmental toxicants, food additives, and so on. Although it was hoped that testing procedures of guideline would be updated constantly to reflect the current state of the science in reproductive and developmental toxicology, it was not until this decade that regulatory guidelines and testing methods have been altered in a significant way. In this paper, we would like to present the recommended approaches and recent trends for improvement of testing guidelines or experimental methods in reproductive and developmental toxicology.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.31 no.3
• /
• pp.185-193
• /
• 2021

Objectives: Inhalation toxicity testing of chemical substances to identify carcinogenicity requires a long time and considerable cost, so the selection of test candidates is a very important aspect. This study was performed to determine optimal procedures for selecting carcinogenic inhalation toxicity test substances as conducted by the Occupational Safety and Health Research Institute (OSHRI). Methods: At the beginning, a database was constructed containing complex information such as usage amount, hazard, carcinogenicity prediction, and testability in order to select chemicals requiring carcinogenicity testing. Selection of test substances was carried out with priority given to usage, carcinogenicity, and testability. Results: Chemicals used in large quantities in industrial fields and strongly suspected of carcinogenicity were winnowed down to 12 substances, and these substances were scheduled for future testing by OSHRI. Conclusions: For the stable and reliable operation of carcinogenicity tests as conducted by OSHRI, this study standardized the procedures for selecting carcinogenicity test substances and suggested the introduction of various carcinogenicity prediction techniques.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.849-860
• /
• 1996

Natural zeolites which were known to occur in sedimentary clinoptilolite, were treated by thermal and chemical methods, and their adsorption characteristics of Cu(II) were studied. Analyses by FT-IR, S. E. M, TGA/DSC, and XRD showed that the adsorption capacity of Cu(II) on the zeolite decreased gradually at the temperatures of above $400^{\circ}C$. The zeolites, which treated with NaOH and NaCl, show higher absorbility in acid solution. The adsorption rate of Cu(II) in the presence of surfactants(LAS, POE AE) on the thermally or chemically treated zeolites varied depending on pH, anion or nonion surfactants.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.3
• /
• pp.177-183
• /
• 2018

PURPOSE. The purpose of the current study was to evaluate the effect of incorporating nanoparticles of silver (NAg) and amorphous calcium phosphate (NACP) into a self-etching primer of a resin cement on the microtensile bond strength of dentin, regarding the proven antibacterial feature of NAg and remineralizing effect of NACP. MATERIALS AND METHODS. Flat, mid-coronal dentin from 20 intact extracted human third molars were prepared for cementation using Panavia F2.0 cement. The teeth were randomly divided into the four test groups (n=5) according to the experimental cement primer composition: cement primer without change (control group), primer with 1% (wt) of NACP, primer with 1% (wt) of physical mixture of NACP+Nag, and primer with 1% (wt) of chemical mixture of NACP+Nag. The resin cement was used according to the manufacturer's instructions. After storage in distilled water at $37^{\circ}C$ for 24 h, the bonded samples were sectioned longitudinally to produce $1.0{\times}1.0mm$ beams for micro-tensile bond strength testing in a universal testing machine. Failure modes at the dentin-resin interface were observed using a stereomicroscope. The data were analyzed by one-way ANOVA and Tukey's post-hoc tests and the level of significance was set at 0.05. RESULTS. The lowest mean microtensile bond strength was obtained for the NACP group. Tukey's test showed that the bond strength of the control group was significantly higher than those of the other experimental groups, except for group 4 (chemical mixture of NACP and NAg; P=.67). CONCLUSION. Novel chemical incorporation of NAg-NACP into the self-etching primer of resin cement does not compromise the dentin bond strength.

• Current Photovoltaic Research
• /
• v.5 no.1
• /
• pp.33-37
• /
• 2017

Today, photovoltaic power generation mostly uses Si crystalline solar cell modules. The most vulnerable part of the Si solar cell module is that the power generation decreases due to the temperature rise. But, it is widely used because of low installation cost. In the solar market, where Si crystalline solar cell modules are widely used. The CPV (Concentrated Photovoltaic) module appeared in the solar market. The CPV module reduces the manufacturing cost of the solar cell by using non-Si in the solar cell. Also, there is an advantage that a rise in temperature does not cause a drop in power generation. But this requires high technology to install and has a disadvantage that the initial installation cost is expensive compared to normal Si solar cell module. So that we built a testbed to see these characteristics. The testbed was used to measure the amount of power generation in a long-term outdoor environment and compared with the general Si solar cell module.

• Journal of the Korean Applied Science and Technology
• /
• v.14 no.1
• /
• pp.53-59
• /
• 1997

Spin finish(NSFs) for synthetic fiber were prepared. NSF-3 was proved to be the best spin finish by testing the properties and emulsion stability, etc. of NSFs. NSF-3 prepared by blending of spindle oil 70g, paraffin wax 10g, glyceryl mono-oleate 5g, POE(10) nonylphenyl ether 4g, POE(20) sorbitan tri-oleate 4g, Na-dioctyl sulfosuccinate 4g, antistatic agent 2g and water 1g was excellent in its characteristics. Optimum physical conditions of nylon filament treated with NSF-3 according to the number of revolution of oil roller were obtained at conditions of 5.5rpm in the number of revolution of oil roller, 1.21% of oil pick up, and denier 69.2D.

• Macromolecular Research
• /
• v.17 no.6
• /
• pp.417-423
• /
• 2009

The effects of maleic anhydride-grafted polypropylene (PP-g-MAH) addition on polypropylene (PP) and poly(acrylonitrile-butadiene-styrene) (ABS) blends were studied. Blends of PP/ABS (70/30, wt%) with PP-g-MAH were prepared by a twin-screw extruder. From the results of mechanical testing, the impact, tensile and flexural strengths of the blends were maximized at a PP-g-MAH content 3 phr. The increased mechanical strength of the blends with the PP-g-MAH addition was attributed to the compatibilizing effect of the PP and ABS blends. In the morphological studies, the droplet size of ABS was minimized (6.6 ${\mu}m$) at a PP-g-MAH content of 3 phr. From the rheological examination, the complex viscosity was maximized at a PP-g-MAH content of 3 phr. These mechanical, morphological and rheological results indicated that the compatibility of the PP/ABS (70/30) blends is increased with PP-g-MAH addition to an optimum blend at a PP-g-MAH content of 3 phr.

• Archives of Pharmacal Research
• /
• v.19 no.2
• /
• pp.143-147
• /
• 1996

LB20304 is a novel fluoroquinolone that exhibits a potent broad spectrum antibacterial activity against both gram-positve and gram-negative bacteria. The MICs (Minimal Inhibitory Concentration) of LB20304 were determined against both gram-positve and gram-negative bacteria under various conditions including several media, pHs, and inoculum concentrations. The in vitro activity of LB20304 was not significantly affected by the changes in testing conditions such as components of media and inoculum concentrations, but it was slightly reduced by acid condition. The MICs and MBCs (Minimal Bactericidal Concentration) of LB20304 against Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa were hardly affected by the presence of 50 % human serum, mouse serum, guinea pig serum or horse serum, and the MBCs were equal to or at most four-times higher than the MiCs. The activities of LB20304 were decreased by the presence of high concentraion of $Mg^{++}$ or human urine (pH, 5.5) in the test media. The frequencies of mutants resistant to LB20304 were similar to or lower than those found in ciprofloxacin and sparfloxacin.

• Membrane and Water Treatment
• /
• v.13 no.4
• /
• pp.173-181
• /
• 2022

Polyvinylidene fluoride (PVDF) flat sheet hydrophobic membranes were prepared using 16 wt% PVDF in Dimethyl acetamide (DMAc) by phase inversion technique for desalination application using Membrane Distillation (MD). In this work, the effect of coagulation mediums such as ethanol and water as well their synergistic behavior on the fabricated PVDF membrane morphology was studied using SEM. Moreover, other characteristics required for the membrane distillation applications namely porosity, hydrophobicity and tensile strength were measured using the gravimetric method, sessile drop method and universal testing machine respectively. It was observed that the membrane morphology paradigm shifted from the finger-like structure to the sponge-like structure on increasing the ethanol concentration in coagulant. The porosity of the fabricated membrane was under the required MD range and found to be 57.3% at 16 weight % of PVDF in DMAc solvent under a pure ethanol coagulant bath. Moreover, the top surface contact angle ranges from 85° to 115° on increasing the bath concentration from CBC 0 to CBC 100 at 16 weight % of PVDF in DMAc solvent.