• Journal of the Korean Ceramic Society
• /
• v.55 no.2
• /
• pp.153-159
• /
• 2018

Porous ceramic plates were prepared from Onggi clay and bamboo charcoal powder at 1100 and $1200^{\circ}C$ and their porous properties and water absorption, and the cooling effect of porous plates, were investigated to produce eco-friendly porous ceramics for a self-cooling system that relies on the evaporation of absorbed water. Porous properties were dependent on the particle size of charcoal powder pore forming additive and the firing temperature; properties were also found to be dependent on the total pore volume, average pore size and porosity, which had values of $0.103-0.243cm^3/g$, 0.81 - 2.56 mm and 20.9 - 38.2%, respectively, at $1100^{\circ}C$ and $0.04-0.18cm^3/g$, 0.33 - 2.03 mm and 10.8 - 30.9%, respectively, at $1200^{\circ}C$. Cooling temperature difference of flowing air parallel to surface of porous ceramic plates fired with two kinds of charcoal powder at $1100^{\circ}C$ was $3.5-3.6^{\circ}C$ at $26^{\circ}C$ and 60% of relative humidity in a closed box. Cooling temperature difference was dependent on the number of porous plates and the distance between porous plates. A simple and eco-friendly cooling system using porous ceramic plates fired from Onggi clay and charcoal powder was proposed.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.80-84
• /
• 2007

Charcoal was used as a carbon source for improving the critical current density of $MgB_2$ and the effect of annealing temperature on the $J_c$ of $MgB_2$ was investigated. The charcoal powder used in this study was $1{\sim}2$ microns in size and was prepared by wet attrition milling. $MgB_2$ bulk samples with a nominal composition of $Mg(B_{0.95}C_{0.05})_2$ were prepared by in situ process of Mg and B powders. The powder mixture was uniaxially compacted into pellets and heat treated at temperatures of $650^{\circ}C\;-\;1000^{\circ}C$ for 30 minutes in flowing Ar gas. It was found that superconducting transition temperature of $Mg(B_{0.95}C_{0.05})_2$ decreased by charcoal additions which indicates the carbon substitution for boron site. $J_c$ of $Mg(B_{0.95}C_{0.05})_2$ was lower than that of the undoped $MgB_2$ at the magnetic fields smaller than 4 Tesla, while it was higher than that of the undoped sample especially at the magnetic field higher than 4 T. High temperature annealing seems to be effective in increasing $J_c$ due to the enhanced carbon diffusion into boron sites.

• Journal of Gastric Cancer
• /
• v.6 no.4
• /
• pp.291-294
• /
• 2006

F-18 FDG-PET/CT could be used to evaluate the surveillance of recurrent stomach cancer, but some cases reported as false-positives. The authors found an activated charcoal granuloma from intraperitoneal chemotherapy by using a curative resection and mitomycin C for stomach cancer. A mass behind the right colon that showed on CT 6 months after an operation in a 46-year-old male patient had no progression in size, but 36 months after the operation, an increase was seen on F-18 FDG-PET/CT, and a metastatic tumor was suspected. The tumor was resected by an explorative laparotomy and was diagnosed as being an activated charcoal granuloma based on the histologic finding. Based on this case, we should be reminded of the possibility of a false-positive on analysis of F-18 FDG-PET/CT caused by an activated charcoal granuloma in a patient who has intraperitoneal chemotherapy.

• Journal of radiological science and technology
• /
• v.29 no.2
• /
• pp.53-56
• /
• 2006

The purpose of the present study is to find ways to reduce the quantity of indoor radon contamination. The study was done from July, 2005 until December, 2005. It was found out that the easiest and most effective way to do that is to open the windows as often as possible and let the indoor air flow outside. When it is not possible to ventilate a room, the indoor radon contamination quantity can reduced by providing activated charcoal in the room. It has been proved that activated charcoal can absorb the room in the air. We need more activated charcoal in proportion to the size of the room. A further research is needed to investigate the amount of activated charcoal that will work most effectively.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.4
• /
• pp.74-81
• /
• 2008

The writing brush, ink stick, paper, and ink stone were the four precious things of the studying and recording in oriental world until even nowaday. The oriental paper was comparatively well evaluated in many papers and reviews, but it is difficult to find some scientific reports or reviews about the ink stick. In this paper, the scientific aspect of ink sticks of oriental maine three country(Korea, China, Japan) were evaluated by the physical, chemical and microscopic analysis. The result could summarized as fellows; 1. The Korean lampblack ink stick contains more carbon and less nitrogen and the Chinese ink sticks contain less carbon and more oxygen. 2. The Korean lampblack and cowhide glue contain relatively higher amount of sulphur. 3. The particle size distribution of carbon in the ink stick was not change after grinding in the ink stone. 4. The particle size of carbon and the pore size in the charcoal ink sticks of three country were larger than those of the lampblack ink sticks. 5. The ink solution of the charcoal ink sticks shows high roundness on Hanji while the ink solution of the lampblack ink sticks is spread readily to Hanji surface. 6. The change of whiteness in printing of the ink sticks is notable in thermal treatment.

• Clean Technology
• /
• v.26 no.2
• /
• pp.131-136
• /
• 2020

Biomass bamboo charcoal is utilized as anode for lithium-ion battery in an effort to find an alternative to conventional resources such as cokes and petroleum pitches. The amorphous phase of the bamboo charcoal is partially converted to graphite through a low temperature graphitization process with iron oxide nanoparticle catalyst impregnated into the bamboo charcoal. An optimum catalysis amount for the graphitization is determined based on the characterization results of TEM, Raman spectroscopy, and XRD. It is found that the graphitization occurs surrounding the surface of the catalysis, and large pores are formed after the removal of the catalysis. The formation of the large pores increases the pore volume and, as a result, reduces the surface area of the graphitized bamboo charcoal. The partial graphitization of the pristine bamboo charcoal improves the discharge capacity and coulombic efficiency compared to the pristine counterpart. However, the discharge capacity of the graphitized charcoal at elevated current density is decreased due to the reduced surface area. These results indicate that the size of the catalysis formed in in-situ graphitization is a critical parameter to determine the battery performance and thus should be tuned as small as one of the pristine charcoal to retain the surface area and eventually improve the discharge capacity at high current density.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.2
• /
• pp.181-195
• /
• 2020

Characteristics of carbonized biomass obtained from a Wood charcoal briquette manufacturing process using an open hearth kiln are analyzed in this research, and differences in the characteristics based on the results of a mechanical screening process and the position within the kiln. One type of biomass and five types of carbonized biomass were collected from a Wood charcoal briquette manufacturer. After screening and grinding processes were performed on samples of 1 type of biomass and 5 types of carbonized biomass extracted from a Wood charcoal briquettes manufacturer to classify by particle size, fixed carbon, ash, volatile matters, elemental composition, and high heating value (HHV) were measured. Experimental results showed that the carbonized biomass collected from the middle layer had the highest HHV, 20.4 MJ/kg, and therefore had the highest fuel quality. In terms of particle size, the carbonized biomass below 100 mesh had the lowest ash content and the highest HHV, carbon content, and fixed carbon content. Correlation analyses showed that ash content had negative correlations with HHV, volatile matters, fixed carbon, and carbon content, which suggested that ash content affected negatively on fuel quality.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.2
• /
• pp.6-15
• /
• 1998

A total of forty five-ply, 30- by 30-cm lauan and larch plywood sheets were manufactured in the laboratory using commercial urea and phenol resin adhesives; half of these sheets were treated with fresh concrete. Each sheet was carbonized for 2, 4, and 6hours at $400^{\circ}C$, $600^{\circ}C$, and $750^{\circ}C$, respectively, and their physical properties were measured. The yie1d of charcoal decreased as carbonization temperature and time increased. Charcoal yield was greater in plywood than in veneer, and slightly greater in plywood treated with concrete compared to untreated plywood. Plywood manufactured with phenol resin adhesive had higher pH, higher equilibrium moisture content (EMC), and greater adsorption of methylene-blue dye compared to plywood manufactured with urea resin. For concrete-treated plywood, pH was greater than 10 even when the sheets were carbonized for 2hours at $400^{\circ}C$. Although the EMC of the phenol resin plywood was higher than that of the urea resin plywood, EMC of the phenol resin was lower than that of the urea resin. The larch phenol resin plywood that was carbonized for 6 hours at $750^{\circ}C$ adsorbed more methylene-blue than did the commercia1 wood-based activated charcoal as a result of total pore volume and surface area.

• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.47-53
• /
• 1962

The "reactivity" of coal is one of the important characteristics of a coal used as a process raw material as well as a fuel. In this study, the reactivity was measured in terms of the magnitude of the reaction rate constant in the reduction of carbon dioxide with coal. A reactivity-testing apparatus was designed and constructed, and its performance characteristics were investigated by using Korean anthracite and hard-wood charcoal. Experiments were carried out at temperatures ranging from 750 to 1100$^{\circ}C$ with pulverized Korean anthracite whose sizes range from 1 to 10mm in diameter. Results showed that the reaction rate constant was not appreciably affected by the particle size investigated, and the reactivities of the anthracite and the charcoal were found to be a function of reaction temperature alone. It was also found that a straight line was produced when the logarithm of the rate constant is plotted against the reciprocal of the absolute temperature. The reactivities of the charcoal were found to be 2 to 10 times higher than those of the anthracite at a temperature ranging from 750 to 1100$^{\circ}C$, and 90% of carbon dioxide was reduced to carbon monoxide by the anthracite at a temperature above 1050$^{\circ}C$.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.7
• /
• pp.1205-1219
• /
• 2010

This study analyzes the conditions and products of internet shopping malls that sell natural dyeing products. In this study, 98 natural dyeing internet shopping malls were selected. The results of this study are as follows. The locations of the internet shopping malls were Gyeonggi-do, Seoul, Jeollanam-do, Gyeongsangbuk-do, Gwang-ju (city), Daegu (city), Busan (city), Gyeongsangnam-do, and Jeju-do. The most frequent dyes of the natural dyeing products were loess, followed by charcoal, indigo, and persimmon. Indigo was most frequently used in Seoul, with loess and charcoal most frequent in Gyeonggi-do. Persimmon, indigo, loess, and charcoal were mainly used in Jeollanam-do, with persimmon and loess in the Gyeongsangbuk-do, and persimmon in Jeju-do. The highest ordered product categories were accessories, followed by adult clothing, interior decoration products, and bedding. The most frequent products were bedclothes, followed by scarves, female shirts, blouses, pillows, female jackets, and vests. Regarding the price of products, 150,000-200,000 won was the highest for the Saenghwal Hanbok, with 10,000-30,000 won for underwear, 30,000-60,000 won for accessories, and 100,000-150,000 won for bedding. Concerning product information, 58.2% of internet shopping malls offer the product size and almost half of them did not show the properties or directions for handling the product. Based on the research results, the problems of the conditions and products of natural dyeing internet shopping mall were derived. The results show that the natural dyes of internet shopping malls lacked regional symbolism, the products were not specialized, and product information was not fully offered to consumers. To solve these problems, the strategies for marketing the promotion of the natural dyeing internet shopping mall were, ‘Using natural dyes from local resources’, ‘Market oriented and specialized item design’, and ‘Offer right product information’.