• 한국산업보건학회지
• /
• 제24권2호
• /
• pp.193-200
• /
• 2014

Objectives: To develop domestic charcoal tubes with good adsorption capacity, breakthrough experiments were performed on four types of activated charcoal. Materials: The adsorption capacity and the adsorption rate were determined using a modified Wheeler equation after the breakthrough experiment. For four types of charcoal (J, K, S and SKC Inc. 226-01), 100 mg were used in the breakthrough experiment. The test was done on benzene, toluene, n-hexane, and acetone in a dynamic chamber. Results: K charcoal had the greatest surface area and the highest micropore volume. J charcoal had a similar surface area and micropore volume to SKC charcoal. S charcoal had the lowest surface area and micropore volume. J charcoal had the highest adsorption capacity at 101, 252 and 609 ppm of benzene. The gap in benzene adsorption capacity among the types of charcoal was the least at 609 ppm and the greatest at 101 ppm. J charcoal showed the highest adsorption capacity at 54, 106, 228 and 508 ppm of toluene. J charcoal and SKC charcoal had a similar adsorption capacity for acetone. J charcoal had the highest adsorption capacity for n-hexane. In the experiment featuring 10% breakthrough volume, 10% breakthrough occurred at 18 liters at $2065.9mg/m^3$ for J charcoal and at 20 liters at $1771.2mg/m^3$ for K charcoal. It was difficult to judge adsorption capacity by surface area and micropore volume of charcoal. J charcoal, which was similar to SKC charcoal in surface area and micropore volume, showed good adsorption capacity at common workplace concentrations. Conclusions: The adsorption capacity of J and K charcoal was superior compared with SKC charcoal. J and K charcoal can be considered appropriate for use as sampling media based on this result.

• 한국산업보건학회지
• /
• 제15권1호
• /
• pp.8-18
• /
• 2005

Adsorption capacity for the charcoal were tasted in this study to verify the performance of them for the use of the sampling media in industrial hygiene field. Two set of experiments were conducted. The first experiment was to test performance of the tested charcoal tube that were assembled in the laboratory with the use of the GR grade charcoal. The other tests were investigate the adsorption capacity of the charcoal tested in this study and charcoals embedded in the commercial charcoal tubes. Known air concentration samples for benzene, toluene, and o-xylene were prepared by the dynamic chamber. 1. At low air concentration levels (0.1${\times}$TLV), there was no significant differences between the tested charcoal tubes and the SKC charcoal tubes. This implies that there is no defect with the adsorption capacity of the charcoal. 2. At high concentration with 60 minutes sampling, the breakthrough were found only in the tested charcoal while no breakthrough were shown in the SKC charcoal. 3. From the breakthrough tests for the charcoal, the micropore volume(Wo) were calculated by the curve fitting with the use of Dubinin/Radushkevich(D/R) adsorption isotherm equation. The calculated values were 0.687cc/g for SKC, 0.504cc/g for Sensidyne, and 0.419cc/g for the tested charcoal(Aldrich). 4. Adsorption capacities were obtained from the isotherm curves shown adsorption capacities at several levels of the challenge concentration. All range of the air concentration concerned in industrial hygiene, the SKC charcoal showed approximately two times of adsorption capacity compared to the tested charcoal.

• 한국환경보건학회지
• /
• 제37권1호
• /
• pp.50-56
• /
• 2011

The adsorption capacity of charcoal is a function of the airborne concentration of the target chemical. To evaluate the adsorption capacity of charcoal packed in the cartridges of air purifying respirators, breakthrough tests were conducted with carbon tetrachloride for three commercial cartridges (3M models #7251, #6000 and AX) at 25, 50, 100, 250 and 500 ppm. Adsorption capacities were calculated using a mass transfer balance equation derived from the curve fitting to the breakthrough curves obtained experimentally. Carbon micropore volumes were estimated by iteration to fit the Dubinin/Radushkevich (D/R) adsorption isotherm. They were 0.6566, 0.5727 and 0.3087 g/cc for #7251, #6000 and the AX cartridge, respectively. Above 100 ppm (at high challenge concentrations), #7251 and #6000 showed higher adsorption capacities. However, as the challenge concentration decreased, the adsorption capacities of #7251 and #6000 sharply dropped. On the other hand, the adsorption capacity of the AX cartridge showed little change with the decrease of the challenge concentration. Thus, the AX showed a higher adsorption capacity than #7251 and #6000 at the 5-50 ppm level. It is concluded that service-life tests of cartridges and adsorption capacity tests of charcoal should be conducted at challenge concentration levels reflecting actual working environmental conditions. Alternatively, it is recommended to use the D/R adsorption isotherm to extrapolate adsorption capacity at low concentration levels from the high concentration levels at which breakthrough tests are conducted, at a minimum of two different concentration levels.

• 환경위생공학
• /
• 제22권1호
• /
• pp.17-27
• /
• 2007

This study was conducted the adsorption experiment way of organic wastewater (BOD, COD, TOC, T-N, T-P) by changing the carbonization temperature and the size of adsorbent to examine the adsorption capacity of Korean traditional charcoal which has similar characteristics to activated carbon of organic pollutants. Also, it was performed the basic experiment for pH and inorganic materials. As a result of observing Korean traditional charcoal with has the greatest inorganic contents which are the important factor of chemical adsorption. As the carbonization temperature was better high temperature charcoal than law temperature charcoal to adsorption capacity of pollutant and as the particle was minute (D size : $3.35mm{\sim}2.0mm$), it was most effective. The result of adsorption experiment of organic wastewater show that the elimination ratio of pollutants by bamboo high temperature charcoal was found as BOD(82.1%), COD(91.7%), TOC(52.4%), T-N(66.6%), T-P(83.2%) and it has most excellent adsorption capacity of organic pollutants.

• 한국가구학회지
• /
• 제14권1호
• /
• pp.1-9
• /
• 2003

This research was carried out for packing materials and building materials to examine thylene gas adsorption and effect of keeping fruit fresh of wet formed charcoal-fiber mposite made from defibrated fiber of Pinus densiflora Sieb. et Zucc. and white charcoal from uercus variabilis Bl.(wood fiber: charcoal=8:2, 6:4, 4:6, 2:8), with/without phenol formaldehyde resin(PF, Non volatile content:$52\%$, resin content $1,3,5\%$). The results are summarized as follows: 1. The higher the charcoal content, the more the ethylene gas adsorption. At the same mixing ratio of fiber to charcoal, $\#100-200$ of charcoal particle size gave the better reslts than $\#60-100$. 2. Adding PF into the charcoal fiber composite decreased the capacity of ethylene gas adsorption but there was no significant difference until $5\%$ adding amount of PF. 3. For keeping fruit fresh for a long time, Charcoal fiber composite was $66\%$ longer than control. The higher the white charcoal content, the longer fresh time.

• 환경위생공학
• /
• 제21권4호
• /
• pp.77-86
• /
• 2006

The water purification was very important in Korea which has not sufficient water resource and while adsorption method among the various methods to eliminate the water pollutants has been widely used by activated carbon. This study was conducted the basic experiment for hall distribution, pH, conductivity, electronic microscope, cation exchange and inorganic materials the adsorption capacity of Korean traditional charcoal which has similar characteristics to activated carbon of organic pollutants. As a result of observing Korean traditional charcoal with electronic microscope, it was found that it has porous structure, oak charcoal has circular structure, pine charcoal has square structure and bamboo charcoal has hexagonal structure, which has high void fraction per unit area because of its thin cell wall structure. As a result of experimenting hall distribution, hall distribution of bamboo high temperature charcoal is high as 0.269cc/g and has the greatest inorganic contents and cation exchange capacity(CEC) which are the important factor of chemical adsorption.

• 한국물환경학회지
• /
• 제16권4호
• /
• pp.555-563
• /
• 2000

The study was conducted to evaluate the adsorption equilibrium of heavy metals on bone charcoal made of livestock bone which was sintered at $550{\sim}600^{\circ}C$. Analysis of bone charcoal by XRD and FT-IR showed that crystal structure was similar to that of synthetic hydroxyapatite. Adsorption equilibrium capacity of single component (Pb, Cd, and Zn) on bone charcoal could be expressed as Langmuir, Freundlich, and Sips equations. Sips isotherm was best among the three isotherms. The values predicted by IAST(ideal adsorbed solution theory) showed good relationship to the experimental data in multicomponent adsorption equilibrium. Adsorption affinity was in order of Pb, Cd, and Zn. The order was same in case of activated carbon or synthetic hydroxyapatite. Through the study results. it would be expected that bone charcoal made of livestock could be used in field of wastewater treatment plants as adsorbent to remove heavy metal.

• Journal of the Korean Wood Science and Technology
• /
• 제33권3호통권131호
• /
• pp.45-52
• /
• 2005

북양젓나무(Abies sibirica Ledeb)의 목분, 목섬유, 수피를 탄화하여 획득한 목탄의 물성과 흡착특성을 탄화온도별로 조사하였다. 전체적으로 탄화온도가 상승할수록 탄화수율은 감소하였다. 목탄의 탄소함량은 탄화온도의 상승과 함께 증가하였으나, 수소나 산소의 함량은 감소하였다. 수피탄화물은 목분 또는 목섬유 탄화물과 비교하여 탄화수율이 높게 나타났으며, 수피탄화물 내 회분함량도 상당히 높았다. 목질탄화물의 요오드흡착능은 탄화온도가 높을수록 향상되었으며, 목분이나 섬유 탄화물이 수피탄화물보다 상대적으로 높았다. 기상의 톨루엔에 대한 흡착능은 목탄 종류에 관계없이 $600^{\circ}C$에서 탄화하였을 경우 가장 높게 나타났으며, 이러한 결과는 $600^{\circ}C$에서 생산한 목탄이 비표면적과 총세공용적이 가장 크다는 사실로 쉽게 설명되어진다. 초산가스제거율은 고온탄화물일수록 크고, 암모니아 가스 제거율은 $400^{\circ}C$와 같은 저온에서 탄화한 탄화물이 높은 경향을 나타내었다. 이는 고온탄화물일수록 알칼리성을 나타내는 반면 저온탄화물은 산성을 나타내는 것에 기인하는 것으로 보인다. 따라서 목탄의 pH가 산 또는 염기성 가스 흡착능력에 큰 영향을 주는 것으로 생각된다.

• Korean Chemical Engineering Research
• /
• 제60권3호
• /
• pp.377-385
• /
• 2022

우리나라 전통 숯가마로부터 제조된 숯의 표면형상과 흡착특성을 분석한 후, 습도와 온도를 조절하면서 이들의 수분 흡착성능을 측정하고 황토, 활성탄소섬유 직포 및 활성탄소섬유 종이의 수분 흡착성능과 비교하였다. 숯은 소수성이므로 45% 이하의 습도에서는 수분을 잘 흡착하지 않지만 습도가 증가하면 흡착성능이 서서히 1차식에 비례하여 증가하였다. 황토 분말도 낮은 습도에서는 숯과 유사했지만 습도가 증가하면 흡착성능이 기하급수적으로 증가하면서 Type V 등온흡착곡선을 보였다. 따라서 조선시대에 기상청 직원들이 숯과 황토의 수분 흡착능력을 일기예보에 적용하였다는 기록을 실험적으로 확인할 수 있었다. 활성탄소섬유 직포와 활성탄소섬유 종이는 수분 흡착능력이 월등하고 신속한 반응을 보이므로 습도측정 센서에 적용할 수 있다고 판단된다. 숯 조각의 등온흡착 및 탈착곡선 측정에서 흡착질인 질소의 탈착이 잘 이루어지지 않아 낮은 압력 이력현상(low-pressure hysteresis)이라는 독특한 Type I과 Type IV의 혼합형태를 보이는데, 이는 질소입자가 흡착시에 숯 세공의 틈새를 비비고 들어가 단단히 끼었다가 탈착시에 빠져나오지 않기 때문이다. 숯을 분말로 분쇄하면 이러한 틈새들이 분쇄되어 비표면적이 증가하고 낮은 상대압력에서 흡착질의 탈착량이 증가되었다.

• 수산해양교육연구
• /
• 제26권5호
• /
• pp.1083-1089
• /
• 2014

The aims of this study are to find out the possibility of the charcoal as a desiccant. The only humidity control under high temperature and high humidity environment can be provided to the thermal comfort at indoor environment. Functionality of charcoal is known to be deodorization, antiseptic effect, filtering effect and humidity control. But research related to humidity control in the country not yet. Thus, the dehumidification capacity of the charcoal experimental results to see the results were as follows : 1) Entering the experimental humidification is 148.02 g/h, 161.05 g/h and 243.2 g/h when air velocity was changed 1.5 m/s, 1.7 m/s and 2.0 m/s. 2) When the basis weight of the charcoal 2.0 m/s air velocity to obtain the largest number of adsorption capacity. 3) Dru bulb temperature and dew point temperature ware measured at front and rear of the charcoal. Absolute humidity is calculated from the measured Dry bulb temperature and dew point temperature. The quantity of dehumidification is calculated from absolute humidity is the largest 129.6 g/h at the air velocity 2.0 m/s.