• 한국농공학회지
• /
• 제39권6호
• /
• pp.67-79
• /
• 1997

The perpose of this study was to suggest the experimental characteristic of the Cherepnov Water Lifter following the drain mode. The Cherepnov Water Lifter(CWL), which is powered by the potential energy of water, can be set to operate automatically when the water m a tank is drained. In this study, a CWL is constructed in the valve drain controlling mode(VCM) and the siphon drain controlling mode(SCM), and a pressure transducer is installed. It was found that, in the VCM, intake flow volume is proportional to both delivery flow volume and drain flow volume. In the SCM, intake flow volume is proportional to drain flow volume, and the average delivery rate is proportional to both efficiency and the water utilization ratio. Also, in the VCM, the water utilization ratio is 35~49%, efficiency is 62~9O%, average delivery rate is 12.8~81.2$cm^3$/s, and the average drain rate is 14.O~91.5c$cm^3$/s. On the contrary in the SCM, the water utilization ratio is 1.7~38%, efficiency is 3~58%, average delivery rate is 3.1 ~69.2$cm^3$/s, and the average drain rate is shown as 114.5~ 183$cm^3$/s. As a result of the water utilization ratio, efficiency, average delivery rate, and average drain rate are compared, the VCM is found to be superior and the more economical mode. However, the VCM requires manpower and electricity to operate the electronic machinery involved, while the SCM requires no manpower or electricity at all. An economic evaluation of these differences will be necessary in the future. Also, in the SCM, studies to improve water utilization ratio and efficiency, to find the optimum height of the siphon for decreasing the average drain rate, and to determine the radius of curvature of throat have to be conducted in advance, since a large flow rate is drained during the priming action of the siphon.

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.214-221
• /
• 2001

This paper describes the design of 3-component force/moment sensor with the force and moment ratio of wide range. It can measure the x-direction force Fx, y-direction force Fy and z-direction moment Mz simultaneously. In order to accurately measure forces and moment using 3-component force/moment sensor, it should get suitable force and moment ratio(the ratio of force Fx=200 N and moment Mz=20 Nm is ten to one), and small interference error. In this paper, in order to design the 3-component force/moment sensor with the force and moment ratio of wide range, the procedures are performed as follow : 1) the derivation of the equations to predict the bending strains on the surfaces of the plate-beams under the force or the moments, 2) the determination of the size of the sensing elements of the force/moment sensor by using the derived equations, 3) the Finite Element Method(FEM) analysis and the characteristic test for confirming the strains from the theory analysis, 4) the selection of the attachment locations of the strain gages of each sensor, 5) the analysis of the rated strain and the interference error at the attachment location of strain gages. It reveals that the rated strains calculated from the derived equations make a good agreement with the results from the Finite Element Method analysis and the characteristic test.

• 동력기계공학회지
• /
• 제18권6호
• /
• pp.126-132
• /
• 2014

The P-T characteristics of mixed refrigerant in thermostatic expansion valve sensing bulb were studied using R-134a and R-410A refrigerant. The characteristics of mixed refrigerant were investigated according to pressure variation and the variation of composition ratio of R-134A and R-410A in the temperature range of $-15^{\circ}C{\sim}15^{\circ}C$. The Thermodynamic characteristic values of the mixed refrigerants were identified using the characteristic value analysis program of mixed refrigerant(Refrop v9.0, NIST). The P-T characteristics in the case of the mixing ratio of 90:10 for R-410A and R-134A were the same result as R-22. And the physical properties showed similar results with R-22. The Maximum operating pressure(MOP) of mixed refrigerant showed a tendency to decrease with decreasing the mixing ratio of additive gases($N_2$ or He) gases. The characteristics in the case of the mixing ratio of 80:1 for mixed refrigerant and additive gases were the similar result as Reference refrigerant.(R-22 MOP, Sporlan company) In addition $N_2$ and He, both showed the same results. It was able to confirm that a MOP on the thermostatic expansion valve sensing bulb can be maintained by adjusting the mixing ratio of mixed refrigerant gases and additive gases.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.319-324
• /
• 2001

Recently new practical use way of industry product is required. In this study, to find flowing property of slump, unit weight, the air amount, compressive strength etc. Compressive strength 240, 270kgf/$cm^{2}$, slump 8$\pm$2.5(I), 152$\pm$.5(II)cm, mixing ratio of copper smelting slag decided by 0, 25, 50, 75, 100% gradually, The result of this study was follows ; 1. Unit weight increased 2.2%~4.4% according as mixing ratio of copper smelting slag increases. 2. Slump increased about 2~5% as the mixing ratio increased gradually 3. Compressive strength was increased about 4~28% in copper smelting slag mixing ratio 25~50% and 8~20% decreased more than mixing ratio 75%.

• Journal of the Korean Data and Information Science Society
• /
• 제12권1호
• /
• pp.11-18
• /
• 2001

다구찌가 제안한 파라미터 설계는 제품설계나 공정설계 단계에서 품질특성치의 수행변동(performance variation)을 줄이는데 있다. 파라미터 설계에서 품질평균 근처에서 품질의 변동을 줄일 수 있는 최적조건을 찾는데 있어서 신호대 잡음비(Signal-to-noise ratio; SN비)라는 수행측도(performance measure)를 사용하였다. 그러나 많은 통계학자들은 SN비를 이용한 다구찌 분석 기법을 비판한다. 본 논문에서는 파라미터 설계를 위한 최적조건을 찾는데 있어서 SN비를 사용하지 않는 보다 실질적인 최적방안을 제안한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1142-1148
• /
• 2006

The floating ring seal which is used in the high pressure turbo pump is frequently used in the oxidizer pump and the fuel pump of the turbo pump of the liquid propulsion rocket, because it is able to minimize clearance to decrease the leakage flow rate. But, floating ring seal has a tendency to increase the force which caused instability of system as the eccentricity ratio increases. In this paper, we devised design of floating ring seal which decrease contact area between floating and supporting ring. Modified floating ring seal has a tendency to decrease the eccentricity ratio compare with original floating ring seal. The whirl frequency ratio which is able to distinguish stability of system decrease compare with original floating ring seal

• 한국광학회지
• /
• 제13권6호
• /
• pp.479-485
• /
• 2002

다중모드간섭을 이용한 임의 분배 비율의 광전력 분배기에 대한 벡터 해석법을 제시한다 광전력 분배는 집적 광학의 기초가 되는 부분이며 특히 광전력 비율을 임의로 조절할 수 있다면 많은 응용분야에 유용할 것이다. 본 벡터 해석법은 기존의 다중모드간섭 현상에 대한 해석적 결과를 도식화함으로써 임의 분배 비율의 다중모드간섭 광전력 분배기 설계를 보다 쉽게 할 수 있다는 장점을 가지고 있다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.302-305
• /
• 2007

In recent years, many researches on new storage media with high capacity and information are developing. For manufacture of optical storage with high capacity, the injection molding process is generally used. In order to increase the filling ratio of the injection molding structure, the injection molding process required for high injection pressure, packing pressure and temperature control of the mold. However, conventional injection molding process is difficult to increase the filling ratio using injection master with the range of several nanometers and high aspect ratio. In order to improve and increase filling ratio of nano-structure with high aspect ratio, the active temperature control of injection mold was used. Experimental conditions were used injection pressure, time and temperature. Consequently, by using the peltier device into injection mold, we carried out the efficient and active temperature control of mold at low cost.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.160-163
• /
• 2009

HPA(High Power Amplifier)는 무선통신 시스템에서 필수적으로 요구되는 요소 중의 하나다. 그러나 전력 증폭기는 비선형 특성을 가지고 있으며 신호의 비선형 왜곡을 유발 시키고 인접채널 간섭을 심화시켜 시스템의 효율을 떨어뜨린다. 이러한 문제점을 해결하기 위해 많은 선형화 기법들이 제시되어왔다. 다항식 사전왜곡 기법은 증폭기로 입력되는 신호가 미리 증폭기의 역 특성을 갖도록 하는 기법으로 다항식을 통하여 증폭기를 모델링하기 때문에 수렴 속도가 빠르고 다른 기법들에 비해 좋은 성능을 보인다. 하지만 다항식으로 역 비선형 특성을 구할 경우, 증폭기의 포화영역에서 역 비선형 특성이 거의 무한대가 되어야 하기 때문에 선형화기의 성능이 크게 떨어진다. 본 논문에서는 이러한 문제점을 해결하기 위하여 PAPR(Peak-to-Average Power Ratio) 기법을 적용하여 다항식 사전왜곡 기법의 성능을 향상 시켰다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.161-166
• /
• 2002

The modification factor( k-factor) of equivalent damping ratio utilized in the current state-of-the-practice to account for the imperfection of reinforced concrete structures in hysteresis loop is investigated. From this, it is found that the current modification factor does not include the effect of cyclic loading, one of the important characteristic properties of earthquake loading. This could be taken into account by considering the energy absorption efficiency based on the cummulative plastic deformation. From the study, it is suggested that the current approach for the modification factor for the equivalent damping ratio should be reformed.