• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.349-354
• /
• 2014

This study is a basic research for repair material production which manufactured a Cu repair coating layer on the base material of a Cu plate using kinetic spray process. Furthermore, the manufactured material underwent an annealing heat treatment, and the changes of microstructure and macroscopic properties in the Cu repair coating layer and base material were examined. The powder feedstocks were sphere-shaped pure Cu powders with an average size of $27.7{\mu}m$. The produced repair coating material featured $600{\mu}m$ thickness and 0.8% porosity, and it had an identical ${\alpha}$-Cu single phase as the early powder. The produced Cu repair coating material and base material displayed extremely high adhesion characteristics that produced a boundary difficult to identify. Composition analysis confirmed that the impurities in the base material and repair coating material had no significant differences. Microstructure observation after a $500^{\circ}C/1hr$. heat treatment (vacuum condition) identified recovery, recrystallization and grain growth in the repair coating material and featured a more homogeneous microstructure. The hardness difference (${\Delta}H_v$) between the repair coating material and base material significantly reduced from 87 to 34 after undergoing heat treatment.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.32-36
• /
• 2021

This study was investigated in carbon diffusion behavior of laser-carburized TiZrN coating layer and the changes of mechanical properties. The carbon paste was deposited on TiZrN coatings, and the laser was irradiated to carburize into the coatings. The XRD peak corresponding to the (111) plane shifted to a lower angle after the carburization, showing the lattice expansion by doped carbon. The decreased grain size implied the compression by the grain boundary diffusion of carbon. The XPS spectra for the bonding states of carbon was analyzed that carbon was substitute to nitrogen atoms in TiZrN, as carbide, through the thermal energy of laser. In addition, the combination of sp2 and sp3 hybridized bonds represented the formation of an amorphous carbon. The cross-sectional TEM image and the inverse FFT of the TiZrN coating after carburizing were observed as the wavy shape, confirming the amorphous phase located in grain boundaries. After the carburization, the hardness increased from 34.57 GPa to 38.24 GPa, and the friction coefficient decreased by 83 %. In particular, the ratio of hardness and elastic modulus (H/E) which is used as an index of the elastic recovery, increased from 0.11 to 0.15 and the wear rate improved by 65 %.

• Korean Journal of Materials Research
• /
• v.33 no.10
• /
• pp.393-399
• /
• 2023

In this study, changes in the microstructure and mechanical properties of cast and extruded Al-2Li-1Ce alloy materials were investigated as the Mg content was varied. The density decreased to 2.485, 2.46 and 2.435 g/cm³ when the Mg content in the Al-2Li-1Ce alloy was increased to 2, 4 and 6 wt%, respectively. Intermetallic compounds of Al₁₁Ce₃ were observed in all alloys, while the β-phase of Al₃Mg₂ was observed in alloys containing 6 wt% of Mg. In the extruded material, with increasing Mg content the average grain size decreased to 84.8, 71.6 and 36.2 ㎛, and the fraction of high-angle grain boundaries (greater than 15°) increased to 82.8 %, 88.6 %, and 91.8 %, respectively. This occurred because the increased Mg content promotes dynamic recrystallization during hot extrusion. Tensile test results showed that as the Mg content increased, both the yield strength and tensile strength increased. The yield strength reached 86.1, 107.3, and 186.4 MPa, and the tensile strength reached 215.2, 285, and 360.5 MPa, respectively. However, it is worth noting that the ductility decreased to 27.78 %, 25.65 %, and 20.72 % as the Mg content increased. This reduction in ductility is attributed to the strengthening effect resulting from the increased amount of dissolved Mg, and grain refinement due to dynamic recrystallization.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.777-783
• /
• 2015

Wood is an anisotropic material that shows the changes in hardness, quality and dimensions depending on the types of cells on three cross sections, size, array and so on. It can also be used in different ways according to its use, which requires a meticulous research, in order to maximize the utilization by understanding the nature and use; and by clarifying the theory and technologies. The research on relationship among wood's physical properties, density, and elasticity of modulus have been studied in Korea and abroad, but those studies were based on correlation gained through standardized specimen. Rather, the study on complete product is rare. Moreover, the previous reports are mostly concentrating on vibration mode and batting, though the wood's physical properties as a material have not been in the main focus. Therefore, this study will carried out for analyzing MOE through figuring material property out and comparing frequency adapting to the Canadian HardMaple bat. For comparison of material properties, we studied the annual ring and density of the bat; calculated the MOE with resonance frequency and formula (ASTM C1259); and verified the repulsive force of this material. As a result, the relevance of the resonance frequency and annual ring is weak, and in comparison in the grain direction in wood, the MOE value is higher when the grain direction in wood is excited horizontally than when is excited vertically, because the material is repulsive when grain direction is horizontal.

• Culinary science and hospitality research
• /
• v.21 no.4
• /
• pp.1-15
• /
• 2015

For the consumption extension of Chinese artichoke(Stachys sieboldii MIQ), the quality characteristics and sensory evaluation of white pan bread prepared with different levels of added Chinese artichoke powder(0, 3, 6, 9, and 12%) were investigated. Volume changes of dough, moisture contents(p<0.001), and baking loss rate(p<0.001) decreased with increasing levels of Chinese artichoke powder. In addition, with an increase in the level of Chinese artichoke powder, the volume and specific volume of white pan breads significantly decreased(p<0.001 and p<0.001, respectively) whereas the weight of white pan breads significantly increased (p<0.001). In terms of color, the lightness(L) decreased, but the redness(a) and yellowness(b) increased with increasing Chinese artichoke powder levels(p<0.001). From the texture profile analysis(TPA) of white pan breads, hardness, chewiness(p<0.05), gumminess(p<0.001), and adhesiveness(p<0.001) increased whereas springiness and cohesiveness(p<0.01) decreased according to the levels of added Chinese artichoke powder. In the attribute difference test, crumb color(p<0.001), grain size(p<0.05) decreased whereas grain uniformity, yeast flavor, acridity flavor(p<0.001), plainer taste(p<0.05), sweet taste(p<0.01), acridity taste(p<0.001), firmness, springiness, moistness, softness, and chewiness increased in accordance with levels of added Chinese artichoke powder. Overall acceptability showed that the sample containing 9% Chinese artichoke powder had the highest score (p<0.001). As a result, the optimal ratio of Chinese artichoke powder for white pan bread was determined to be 9%.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.22 no.4
• /
• pp.172-186
• /
• 2017

Current study is a part of the efforts to assess the estuarine barrage effects on the coastal ecosystem induced by the Si flux changes. Surface sediments from Seomjin and Nakdong estuary and sediment cores from Nakdong estuary was analysed to investigate the effect of estuarine barrage on the distribution of grain size, organic matter (loss on ignition: LOI) and biogenic silica (BSi). The samples of Seomjin estuary were collected in March, 2015 and those of Nakdong estuary were collected in November, 2014. Generally, the longitudinal distribution of grain size, LOI and BSi in Seomjin estuary, natural estuary, was gradually changed. However mud (silt and clay), LOI and BSi increased from station mid-estuary where tide reaches year-round. The distribution of grain size, LOI and BSi in Nakdong estuary, however, were entirely different between inside and outside of estuarine barrage. The mud percentage and LOI were low and consistent in inside of the barrage except R05, inside of right gate, yet those of outside of the barrage were higher and varied by adjacent sluices. Mud, LOI and BSi of ND1 and ND2 decreased immediately after the construction of Nakdong estuarine barrage due to disturbance of sediment and decrease of sediment supply. To exclude the physical effects by the barrage, BSi excess ($BSi_{exc}$) was calculated using regression equation of BSi-LOI and BSi-mud of Seomjin estuary. $BSi_{exc}$ of Seomjin estuary decreased gradually from upper estuary to lower estuary. $BSi_{exc}$ of Nakdong estuary were positive in inside of the barrage and negative in outside of the barrage. BSi retention and shift of species composition of diatom by the barrage would affect $BSi_{exc}$ distribution. Before the construction of Nakdong estuarine barrage, $BSi_{exc}$ of ND2 was negative and consistent owing to high mud sedimentation. After the construction, $BSi_{exc}$ of ND2, however, fluctuated due to continuous disturbance of sediment due to construction of Eulsuk bridge and East gate.

• Journal of Distribution Science
• /
• v.12 no.12
• /
• pp.65-73
• /
• 2014

Purpose - Distribution of agricultural products is collapsing due to recent changes in the environment balance between retailers and producers. Further, the increase in the imports of agricultural products due to free trade has caused revenue problems for producers. Agricultural producers are faced with increasing difficulties, and the organized producing center's importance is growing each day. Korean organized producing centers' policies have been conducted since 2000, and have thus been sustained for more than 10 years. Organizing a producing center's business is focused on agricultural cooperative and farming association corporation this has already have been carried out. In addition, it has achieved significant results through these organizations, but it still has many problems. Research design, data, and methodology - Organized producing centers were classified for each type. The survey covered 90 organizations, based on factor analysis, analysis of balance, and logistic regression analysis. The results of the conducted factor analysis are as follows. Production, marketing, human resources management, organizational skills, post management, safety, and scale were classified as the seven kinds of factors. These are the factors that affect the organized producing centers through the variance analysis and logistic regression analysis. The purpose of such research and analysis is to suggest the direction for the future organized producing centers' policies. Result - Results of the analysis of the variance are listed below. Items by type, production, marketing, human resource management, and organizational skills are shown to depict differences between the factors. Organization form results show that production and marketing showed a difference between the factors. The size of the organization, production, and marketing showed the difference between the factors. The factors affect organized producing centers differently depending on the type shown, as seen from the results. In contrast, the logistic regression results of the analysis are as follows. Considering the results by the type of item, and the horticulture type of marketing, human resource management has a (+) influence. Grain type and production showed a (+) influence. New types of income affecting organizational skills have a (+) influence. Considering the results for each type of organization, the agricultural cooperative type of marketing and human resource management have (+) influence. Farming association corporation type of production has a (+) influence. As a result, the size of the organization is as follows. Large organizations are production, expressed in marketing with a (+) impact. Medium-size organizations are expressed with their size factor having a (+) impact. Small organizations are expressed with a safety factor having a (+) impact. Conclusions - The types of factors display different effects. One factor is that the type of a (+) represents the influence of other factors (-) as per factor symptomatology. Therefore, the type of measures to organize a strategy to maximize the benefits of your organization should be pursued. In addition, based on the support for small organizations, improving the quality of the producer organization should be considered.

• Korean Journal of Materials Research
• /
• v.21 no.9
• /
• pp.497-501
• /
• 2011

The CdS thin film used as a window layer in the CdTe thin film solar cell transports photo-generated electrons to the front contact and forms a p-n junction with the CdTe layer. This is why the electrical, optical, and surface properties of the CdS thin film influence the efficiency of the CdTe thin film solar cell. When CdTe thin film solar cells are fabricated, a heat treatment is done to improve the qualities of the CdS thin films. Of the many types of heat treatments, the $CdCl_2$ heat treatment is most widely used because the grain size in CdS thin films increases and interdiffusion between the CdS and the CdTe layer is prevented by the heat treatment. To investigate the changes in the electrical, optical, and surface properties and the crystallinity of the CdS thin films due to heat treatment, CdS thin films were deposited on FTO/glass substrates by the rf magnetron sputtering technique, and then a $CdCl_2$ heat treatment was carried out. After the $CdCl_2$ heat treatment, the clustershaped grains in the CdS thin film increased in size and their boundaries became faint. XRD results show that the crystallinity improved and the crystalline size increased from 15 to 42 nm. The resistivity of the CdS single layer decreased from 3.87 to 0.26 ${\Omega}cm$, and the transmittance in the visible region increased from 64% to 74%.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.3
• /
• pp.268-278
• /
• 2001

To investigate sedimentary facies and environmental changes of the Nakdong River Estuary and its adjacent coastal area, the grain size analysis and measurement of organic matter, calcium carbonate, clay mineral and metallic elements were carried out for forty surface sediment samples. Based on regional distribution pattern and characteristics of the surface sediments, sedimentary facies in the study area can be divided into sand facies (TYPE I), mud facies (TYPE II) and sand-mud mixed facies (TYPE III). TYPE III is the transition of TYPE I and TYPE II in every aspects of sediment characteristics. It suggests that TYPE III may have been formed by the mixture of two different source of sediment : one derived from Nakdong River and the other resuspended fine-grained sediments from the Jinhae Bay by winnowing action during floods or storms. Among many aspects of environmental change after the construction of the Nakdong Barrage, the most significant is the increase of sand content off the sand barrier region. It could be explained by several reasons including decreased input of fine-grained sediment from river, increased hydrodynamic energy level off the sand barrier region and artificial effects such as dredging and dumping.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.21 no.4
• /
• pp.91-107
• /
• 2018

It is required to monitor and assess the desertification in Tunisia, where the Sahara Desert, which is located in the southern part of Tunisia, is recently expanding northward. In this study, by using remote sensed data, land cover changes were examined, and the Normalized Difference Vegetation Index (NDVI), Topsoil Grain Size Index (TGSI) and Albedo are used to monitor and assess desertification in Tunisia. Decision Tree was constructed, and the frequencies and trends of each assessment indicator, desertification degree and land cover were identified. In addition, we analyzed the correlation between assessment indicators and precipitation. As a result, desertification is generally intensifying northward, especially in areas with high levels of desertification. Also, bivariate correlation analysis showed that Albedo, NDVI and TGSI were all highly correlated with precipitation. It indicates that changes in precipitation have also been shown to affect Tunisian desertification. In conclusion, this study has improved the usability of various methodologies considering the assessment indicators based on satellite imagery, Decision Tree, which is a method of evaluating them complexly, and trends of land cover change.