• Textile Coloration and Finishing
• /
• v.17 no.5 s.84
• /
• pp.1-12
• /
• 2005

Polyester fibers can be modified into cationic dyeable polyester fibers(CDP) by the copolymerization of terephthalic acid and 5-sodium sulphoisophthalic acid with ethylene glycol. The advantage of CDP on most cationic dyes is the conspicuous brilliance due to a narrow steep absorption band and the wash fastness and etc. Weight reduction by alkali hydrolysis, dyeing and solvent wicking properties of fabrics with cationic dyes, and change of fine structure were investigated. To obtain optimum splitting process parameters for dyeing and physical properties of micro CDP fiber, splitting method under various conditions was carried out. By means of SEM, it was confirmed that the splitting process of the micro CDP fiber be achieved at the weight reduction. A comparatively greater quantity of dye is necessary to dye microfiber than conventional fiber. The fastness and solvent wicking of regular CDP fiber is higher than that of micro CDP fiber.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.1
• /
• pp.29-43
• /
• 1998

This study was to investigate the effect of .compressive load and cyclic humidity(2$0^{\circ}C$, 65% and 90% RH) on the physical and mechanical properties of corrugated board. Corrugated boards in the study were under compressive load and under cyclic humidity, and their properties were compared to those without load. Results were summarized as follows ; 1 Statistically significant correlation was shown between the ring crush of the boards and the compressive strength of cylinder specimen made from the boards. So we could study the compressive behavior of board with cylinder specimen. 2. The boards under the compressive load increased their moisture content and thickness much more than those without load both in constant and in cyclic RH. 3. The compressive and tensile strength of board samples were inversely and closely proportional to the sheet moisture content regardless of their load and humidity history. 4. The moisture content did not show any significant proportionality to the change of burst strength of boards within this experiment. 5. Board reconditioning in standard condition led to the recovery of the strength loss that had occurred under various load and humidity condition. 6. The handsheets prepared from the boards that had experienced compressive load and cyclic humidity, and those with no-load and 65% RH did not show any significant difference in strength properties. No physical damage or load-carrying properties of the wood fiber were observed by the compressive load and cyclic humidity history.

• Physical Therapy Rehabilitation Science
• /
• v.13 no.1
• /
• pp.95-105
• /
• 2024

Objective: The purpose was to investigate changes in mechanical properties, range of motion, and grip strength of the forearm muscle in 13 students depending on the wrapping direction of the floss band. Design: A single-blind, crossover study Methods: Subjects were randomly assigned to the wrapping direction of the flossing band and then performed a concentric exercise of the wrist flexors using a Flex-Bar. Intervention A applied the flossing band in a right spiral direction, Intervention B applied the flossing band in a left spiral direction, and Intervention C performed the exercise alone. All subjects used their dominant right hand, and pre- and post-assessments were conducted between interventions. To analyze differences in changes between groups pre- and post-, all results were subjected to one-way ANOVA, followed by Scheffe's test as a post-hoc analysis. The paired samples t-test was used to analyze the difference between pre- and post-change within groups. Results: First, in the mechanical properties of the Flexor carpi ulnaris (FCU) muscle, interventions A and B significantly improved muscle tone and stiffness than intervention C (p<0.05), and intervention A showed a significant decrease in decrement (muscle elasticity) than intervention B (p<0.05). Second, interventions A and B showed significant improvement in grip strength than intervention C (p<0.05). Conclusions: The right spiral direction of the flossing band tended to increase the elasticity of the muscles compared to the left spiral direction. Therefore, in future studies, it is necessary to choose the direction of the flossing band to increase the elasticity of the muscles.

• Applied Chemistry for Engineering
• /
• v.25 no.6
• /
• pp.639-644
• /
• 2014

Domestic vehicle companies have been selling genuine engine oils with higher price than that of the same grade of regular engine oils. In this study, our group investigated the properties of engine oils for 14 kinds of the genuine and equivalent regular engine oil (KS product) species under a fresh as well as used condition recovered after 10,000 km driving. From analytic results, genuine engine oils had similar physical properties to regular engine oils under the fresh condition. But recovered regular engine oils had better properties in lubricity, kinematic viscosity and acid number change than those of recovered genuine engine oils.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.682-688
• /
• 2014

Physical and chemical changes in a polished wafer and in $2.5{\mu}m$ & $4{\mu}m$ epitaxially grown Si layer wafers (Epilayer wafer) after surface treatment were investigated. We characterized the influence of surface treatment on wafer properties such as surface roughness and the chemical composition and bonds. After each surface treatment, the physical change of the wafer surface was evaluated by atomic force microscopy to confirm the surface morphology and roughness. In addition, chemical changes in the wafer surface were studied by X-ray photoemission spectroscopy measurement. Changes in the chemical composition were confirmed before and after the surface treatment. By combined analysis of the physical and chemical changes, we found that diluted hydrofluoric acid treatment is more effective than buffered oxide etching for $SiO_2$ removal in both polished and Epi-Layer wafers; however, the etch rate and the surface roughness in the given treatment are different among the polished $2.5{\mu}m$ and $4{\mu}m$ Epi-layer wafers in spite of the identical bulk structural properties of these wafers. This study therefore suggests that independent surface treatment optimization is required for each wafer type, $2.5{\mu}m$ and $4{\mu}m$, due to the meaningful differences in the initial surface chemical and physical properties.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.655-662
• /
• 2003

Slope stability is an important issue ill civil engineering works or in open pit mines where both economy and efficiency is required. These are the long-term stability problems which depend on the change of physical properties under a certain weather condition. These can also result in progress of weathering which can change mechanical or hydro-geological properties of rock mass considerably. In this study, weathering in nature was simulated by freeze-thaw test and Soxhlet test which represent mechanical and chemical weathering respectively. Measured were elastic wave velocities, absorption rate, volume change. Uniaxial compression strengths before and after the weathering tests were also measured. The change in weight and volume of the specimens were not clearly related to the weathering process, but P, S wave velocities were clearly decreased as weathering progresses. For some class of rocks, P-wave velocity was increased probably because of the saturation due to improved connectivity of the pre-existing pores. Based on the test results, stability of the slopes were analyzed using FLAC$\^$2D/. Due to the reduced strength parameters, the factors of safety were decreased for the selected sites.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.5
• /
• pp.18-24
• /
• 2007

The environmental value of coastal vegetation has been widely recognized. Coastal vegetation such as reed forests and seaweed performs several useful functions, including maintaining water quality, supporting fish (and, thus, fisheries), protecting beaches and land from wave attack, stabilizing sea beds and providing scenic value. However, studies on the physical and numerical process of wave propagation, sediment transport and bathymetric change are few and far between compared to those on the hydrodynamic roles of coastal vegetation. In general, vegetation flourishing along the coastal areas attenuates the incident waves through momentum exchange between stagnated water mass in the vegetated area and rapid mass in the un-vegetated area. This study develops a numerical model for describing the wave attenuation and sediment transport in a wave channel in a vegetation area. By comparing these results, the effects of vegetation properties, wave properties and model parameters are clarified.

• Journal of Fashion Business
• /
• v.8 no.6
• /
• pp.1-14
• /
• 2004

On the basis of garment spatial configuration technology, the correlation of fabric properties and garment modeling was studied in this paper. With abundant experimental data, practical modeling and the judgment of fabric properties and physical shape, we analyzed the change rules that restricting all kinds of parameters of fabric properties and garment modeling, and discussed the relation of wavy modeling and all correlated factors of fabric properties. The result showed the basis of choosing fabric for different style garment, which would help designers choosing fabric for modeling design or structure design.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.19 no.1
• /
• pp.64-74
• /
• 2001

This study is to find the effect of the molecular weight distribution of components on the freeness and physical properties of paper by observing the change of properties according the modification of fibers by using production technology and process technology together to develop additives which can effectively control according to the purpose of paper-making process and by combining low molecular weight cellulase (below MW 20,000; CMC activity 400 unit) with different enzyme's molecular weight and activity and high molecular weight cellulase(MW 20,000∼80,000;CMC activity 90,000 unit) and then process them in Sw-BKP(Softwood Bleached Kraft Pulp) and Hw-BKP(Hardwood Bleached Kraft Pulp) and Cotton Linter Pulp and OCC(Old Corrugated Container) with different properties of pore of surface of fibers respectively, since it is judged that making the appropriate composition ratio of components is necessary in consideration of the properties of fibers and paper-making process.

• Journal of the Regional Association of Architectural Institute of Korea
• /
• v.21 no.5
• /
• pp.117-124
• /
• 2019

When manufacturing concrete, several mineral admixture is added to improve the basic physical property and durability and to make economical concrete. Such mineral admixture includes fly ash, granulated blast furnace slag, silica fume, etc., and not only the studies about mixing these mineral admixtures but also the studies for the development of new materials have been steadily in progress. Recently, some researchers have found, as a part of the development of new materials, the rice straw ash can also be used as a pozzolanic material for concrete considering similar chemical properties of rice straw ash to that of rice husk ash. But there has been insufficient amount of study about it. So, this study was to investigate the possibility as mineral admixture of agriculture by-product, by analyzing properties of concretes using rice straw ash with replacement ratio in comparison with other mineral admixture. In order to measure amount of SiO2 of rice straw ash, XRF(X-ray fluorescence) analysis was tested. For the measure pozzolanic reaction of rice straw ash, pH change and color change was tested according to curing day. Also to evaluate properties of concrete using rice straw ash, slump test, air contents test and compressive strength was tested.