• Analytical Science and Technology
• /
• v.10 no.3
• /
• pp.225-229
• /
• 1997

The stability of Rhodamine 6G Perchlorate(Rh6GP) doped in organically modified silicate(Ormosil) was investigated after the Ormosil was synthesized by sol-gel process. The composition of the Ormosil which makes organic dye molecules stable and dimer-free was decided from comparing absorption peaks of dye molecules in sol state, in wet gel and in completely dried gel. The stable and dimer-free Rh6GP doped in the Ormosil was achieved in the 0.1 molar ratio of HCl/TEOS.

• Korean Journal of Materials Research
• /
• v.13 no.11
• /
• pp.725-731
• /
• 2003

The effect of organic processing parameters on the dispersion stability of the BaTiO$_3$-based dielectric particles and borosilicate glass particulate suspensions was investigated in a system where organic solvents, dispersant, binder and modifier were used as processing additives in a low temperature cofired ceramic fabrication processes. Two- and three-component organic solvents were used to disperse ceramic particles and it was found the better stability in the particulate suspension prepared in a bi-solvent, which was consists of toluene and ethanol in a non-azeotropic composition. The addition amount of organic additives had a great impact on dispersion in the present investigation. The flow curves of the suspensions prepared with binder and modifier were fitted according to the power-law equation, which indicates that the internal structure of the suspension could be disturbed under the applied shear stress. Finally, the LTCC green tapes were successfully tape-cast based upon the optimum formulation of LTCC suspension and its microstructure was compared with that of the hard-agglomerates.

• Journal of the Korean Ceramic Society
• /
• v.42 no.8 s.279
• /
• pp.532-536
• /
• 2005

Thermal shock resistance of structural ceramics is a property that is difficult to quantity, and as such is usually expressed in terms of a number of empirical resistance parameters. These are dependant on the conditions imposed, but one method that can be used is the examination of density, Young's modulus and thermal expansion retention after quenching. For high temperature applications, long-annealing thermal durability, cycle thermal stability and residual mechanical properties are very important if these materials are to be used between $1000^{\circ}C$ and $1300^{\circ}C$. In this study, an excellent thermal shock-resistant material based on $Al_2TiO_5-mullite$ composites of various compositions was fabricated by sintering reaction from the individual oxides and adjusting the composition of $Al_2O_3TiO_2/SiO_2$ ratios. The characterization of the damage induced by thermal shock was done by measuring the evolution of the Young's modulus using ultrasonic analysis, density and thermal expansion coefficients.

• Journal of the Korean Ceramic Society
• /
• v.42 no.7 s.278
• /
• pp.455-460
• /
• 2005

Deposition of TiN$_{x}$ film was conducted with a DC sputtering technique. The effect of the processing parameters such as substrate temperature, deposition time, working pressure, bias power, and volumetric flowing rate ratio of Ar to N$_{2}$ gas on the resistivity of TiN$_{x}$ film was systematically investigated. Three kinds of substrates, soda-lime glass, (100) Si wafer, and 111m thermally grown (111) SiO$_{2}$ wafer were used to explore the effect of substrate. The phase of TiN$_{x}$ film was analyzed by XRD peak pattern and deposition rate was determined by measuring the thickness of TiNx film through SEM cross-sectional view. Resistance was obtained by 4 point probe method as a function of processing parameters and types of substrates. Finally, optimum condition for synthesizing TiN$_{x}$ film having lowest resistivity was discussed.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.4
• /
• pp.9-17
• /
• 1998

BiNbO$_{4}$ ceramics with 0.07wt% V$_{2}$O$_{5}$ and 0.03wt% CuO (BNC3V7) sintered at 900 .deg. C where it is possible for these to be co-fired with ag electronde. Dielectric constant of 44.3 TCF (Thermal Coefficient of resonance Frequency) of 2 ppm/.deg. C and Qxf value 22,000 GHz can be obtained from BNC3V7. the laminatedchip LC filter is indispensible to the minimaturization of PCS (Personal Communication System) terminals. Therefore, multilayer type BPF has been fabricated by screen-printing with silver electrode after tape casting. The simulated characteristics of the fabricated filters sintered at 900.deg. C werecomparedwith the designed ones. for Band Pass Filter widths was similar that ofdesigned ones. For Low Pass Filter (LPF), insertion loss value of band pass widths (2.4 dB) which is a few higher than that of designed (1dB), but characteristization of band pass widths was similar that of designed ones.s.of designed ones.s.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.3
• /
• pp.471-481
• /
• 1995

Measurement factors for the dielectric properties of low dielectric loss materials (tan${\dalta}{\le}10^{-4}$) were investigated using the dielectric rod resonator method. It was shown that the relative conductivity (${\sigma}_{r}$) should be controlled within a 5% to obtain the standard deviations of less than 0.07 for permittivity .epsilon.r and 0.06${\times}10^{-4}$ for tan.delta.respectively. Surface resistivity (R$_s$) could be reduced when the surface roughness of parallelled conducting plate was less than 0.07 .mu.m. Measurement error for the permittivity was $\pm$0.02% independent of probe loop size, whereas the error in Q value was reduced with the decrease in probe loop size and also with the increase in the absolute values of Q. Reliable Q values were determined with the probe loop size of less than 4mm. The accurate for the distance between the measuring probe loop and the sample could be obtained when the insertion loss of resonant frequency ranged -15dB - -30dB.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.427-431
• /
• 2012

The $TiO_2$ foam synthesized using freeze-casting is a promising photocatalyst and photovoltaic electrode for a variety of energy applications, because the freeze-casting technique is easy to use, cheap, and suitable for mass-production. Despite its several advantages, little scientific information is available on the processing and morphology of the $TiO_2$ foams processed by freeze-casting. In particular, no systematic study has been performed on the microstructural evolution and morphological change of the rutile-phase $TiO_2$ foams during sintering. Therefore, in the present study, several $TiO_2$ foam samples were produced using the freeze-casting technique, which were then sintered at a relatively high temperature of $1200^{\circ}C$ for 1, 2, and 4 h to compare the morphological changes in the microstructure and to understand the effects of processing parameters of the rutile-phase $TiO_2$ foams. The foam ligament size increased near linearly with increasing sintering time whereas the average pore size decreased only slightly with increasing sintering time, with changes in particle morphology from sphere to rod and complete phase transformation from anatase to rutile.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.517-522
• /
• 2002

In this study, the effect of the processing parameters in PVD process on the size and the distribution of deposited Si quantum dots was quantitatively investigated by computational simulation utilizing Monte Carlo method. The processing parameters, substrate temperature, deposition time, gas pressure and target-substrate distance were selected as variables since those parameters are often selected as variables in PVD experiments. It is predicted that the density of $1{\times}10^{12}cm^{-2}$ Si quantum dots can be deposited on the substrate when the deposition rate is 0.05 nm/sec at the substrate temperature of 490${\circ}$, deposition time of 7 sec, gas pressure of 3 mTorr and target-substrate distance of 8 cm.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.6
• /
• pp.394-399
• /
• 2000

Langasite (LGS) is a material hoped to meet needs required of new base materials for future communication devices (e.g.SAW filters). In this study, synthesis of new materials was pursued by developing new compounds with the host structure of Langasite in hopes to obtain materials with improved characteristics; compounds including $La_3$$Ta_{0.5}$$Ga_{5.5}$$O_{14}$(LTG)and $La_3$$Nb_{0.25}$$Ta_{0.25}$$Ga_{5.5}$$O_{14}$(LNTG) were synthesized by solid state reactions. Characteristics of the compound synthesized in question were determined. The single crystals of Langasite-type were grown using the Czochralski method. The growth conditions for LTG and LNTG were studied and were found to be similar to those of LGS. The growth characteristics of LNTG were observed by studying etch pit formation density along the crystal length.

• Korean Journal of Materials Research
• /
• v.19 no.7
• /
• pp.391-396
• /
• 2009

2-dimensional silica-silica Continuous Fiber-reinforced Ceramic.matrix Composites (CFCCs) were fabricated by a sol-gel infilitration method that has a changing processing condition, such as the repetitions of infilitration. In order to investigate the relationship between the processing condition and the mechanical properties of composites, the mechanical properties of specimens were measured by means of a 4-point flexural strength test while the evidence of strength degradation were microstructurally characterized. There seemed to be a minimum density value that existed at which the delamination between the fabrics would not occur. In the case that the density of silica CFCCs exceeded 1.55 g/$cm^3$, the flexural strength also exceeded approximately 18 MPa at least. By applying the Minimum Solid Area (MSA) analysis of the porous structure, the correlation between the relative density and the mechanical properties of composites will be discussed.