• Tribology and Lubricants
• /
• v.34 no.3
• /
• pp.107-114
• /
• 2018

This paper presents a computational model of a gas foil journal bearing with shim foils between the top foil and bumps, and predicts its static and dynamic performance. The analysis takes the previously developed simple elastic foundation model for the top foil-bump structure and advances it by adding foil models for the "shim foil" and "outer top foil." The outer top foil is installed between the (inner) top foil and bumps, and the shim foil is installed between the inner top foil and outer top foil. Both the inner and outer top foils have an arc length of $360^{\circ}$, but the arc length of the shim foil is shorter, which causes a ramp near its leading edge in the bearing clearance profile. The Reynolds equation for isothermal and isoviscous ideal gas solves the hydrodynamic pressure that develops within the bearing clearance with preloads due to the ramp. The centerline pressure and film thickness predictions show that the shim foil mitigates the peak pressure occurring at the loading direction, and broadens the positive pressure as well as minimum film thickness zones except for the shortest shim foil arc length of $180^{\circ}$. In general, the shim foil decreases the journal eccentricity, and increases the power loss, direct stiffness, and damping coefficients. As the shim foil arc length increases, the journal eccentricity decreases while the attitude angle, minimum film thickness, and direct stiffness/damping coefficients in the horizontal direction increase.

• Structural Engineering and Mechanics
• /
• v.16 no.5
• /
• pp.613-625
• /
• 2003

This paper presents the lateral-torsional buckling (LTB) of beams or girders with continuous lateral support at top flange. Traditional moment gradient factors ($C_b$) given by AISC in LRFD Specification for Structural Steel Buildings and by AASHTO in LRFD Bridge Design Specifications were reviewed. Finite-element method buckling analyses of doubly symmetric I-shaped beams with continuous top bracing were conducted to develop new moment gradient factors. A uniformly distributed load was applied at midheight and either or both end moments were applied at the ends of beams. The proposed solutions are simple and accurate for use by engineers to determine the LTB resistance of beams.

• Journal of Information Display
• /
• v.5 no.1
• /
• pp.28-33
• /
• 2004

A high voltage NMOSFET is proposed to drive top emission organic light emitting device (OLED) used in the organic electroluminescent (EL) display on the single crystal silicon substrate. The high voltage NMOSFET can be fabricated by utilizing a simple layout technique with a standard CMOS logic process. It is clearly shown that the maximum supply voltage ($V_{DD}$) required for the pixel-driving transistor could reach 45 V through analytic and experimental methods. The high voltage NMOSFET was fabricated by using a standard 1.5 ${\mu}m$, 5 V CMOS logic process. From the measurements, we confirmed that the high voltage NMOSFET could sustain the excellent saturation characteristic up to 50 V without breakdown phenomena.

• Journal of the Korean Institute of Gas
• /
• v.5 no.4 s.16
• /
• pp.49-55
• /
• 2001

This paper presents the design safety analysis of the inner tank structure, which is manufactured by 9 percent nickel steel sheets in the full containment type LNG storage tank. The FEM computed results indicate that top girder and several stiffener rings of the inner tank play an important role for controlling the deformation and stress intensity of the inner tank structure. The hydrostatic pressure due to cryogenic fluids gave more influential to the deformation of the inner tank wall compared with that of a cryogenic temperature of $-162^{\circ}C$. But, the deformation and stress of the inner tank. which is produced by the buckling loads, are very small because the external load is not applied to the top of the inner tank. This indicates the role of top girder and stiffener rings of the inner tank model is not important in full containment LNG storage tank.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.11 no.1
• /
• pp.28-35
• /
• 2008

Purpose: The aim of this study is to report the efficacy of infliximab, a monoclonal antibody directed against tumor necrosis factor alpha which is used for both treatment of refractory pediatric Crohn disease (CD) and induction of remission. Methods: Among pediatric patients who were diagnosed with CD at Samsung Medical Center between March 2001 and August 2007, a total of 16 patients were given infliximab to treat conventional therapyresistant refractory CD and severe active CD for induction of remission. Patients needing maintenance therapy were treated with an infliximab infusion every 8 weeks, and fistulizing CD patients occasionally received the infusion upon the condition that a fistula developed. The efficacy of treatment was assessed by comparing the Pediatric Crohn Disease Activity Index (PCDAI), Hct, ESR, CRP, and serum albumin levels using paired t-test. Results: The male/female ratio was 13:3, and the median age was 13 years (range, 21 months~15 years). The patients included 7 cases of therapy-resistant refractory CD, 7 cases of severe active CD, and 2 cases of fistulizing CD. Mean PCDAI before infliximab therapy was 34.19${\pm}$14.96, and mean follow-up PCDAI within 2 to 4 weeks after the last infusion was significantly lower, at 6.88${\pm}$10.31 (p=0.000). Hematological markers such as ESR (p=0.000), serum albumin (p=0.016), and CRP (p=0.009) also improved significantly after infusion. Remission was achieved in 2 of 4 patients refractory to conventional therapy. Among 3 steroid-dependent patients, 2 were able to discontinue steroid therapy, and dose reduction was possible in 1 patient. Remission after top-down therapy without prior use of other immunomodulators was achieved in 6 weeks in all 7 of the patients who had severe CD. Nine of ten refractory fistulizing CD patients also showed improvement after infliximab therapy. Conclusion: Infliximab was effective in pediatric refractory CD for induction of remission and maintenance therapy, as well as in severe CD for top-down induction therapy. Furthermore, infliximab has contributed to steroid cessation and dose reduction. Long-term follow-up evaluation is needed to determine safety and efficacy of infliximab in the future.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.4
• /
• pp.83-89
• /
• 2013

A numerical scheme based on a mode superposition method is presented for the dynamic response analysis of a top-tensioned riser (TTR) under sheared current loads. The natural frequencies and mode shapes of the TTR have been calculated analytically for a beam with a slowly varying tension and pinned-pinned boundary conditions at the top and bottom ends. The lift coefficients and corresponding amplitudes used to estimate the vortex-induced modal force and damping for each mode were predicted via iterative calculations based on the input and output power balancing concept. Here, the power-in regions were controlled by the normal distribution function, for which the center was coincident with the lock -in location by local vortex-shedding, and the range was defined by the constant standard deviation for the reduced velocity by the local current speed. Finally, dynamic responses such as root-mean-squared displacement and stress were calculated using the mode superposition technique. In order to verify the presented scheme, a numerical calculation was performed for a TTR under an arbitrary linearly sheared current and linearly varying tension. A comparison with the results of the existing software showed that the presented scheme could give reliable and feasible solutions. Case studies were performed to investigate the effects of various current loads and tensions.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.4
• /
• pp.263-275
• /
• 2014

In this study, connection of steel reinforced concrete(SRC) column and composite beam which consists of H-section and U-section members were tested under cyclic loading. An essential point of the composite beam is the structural performance of welded joint between the H-section and the U-section members. To improve the structural performance of joint of two beam members, vertical stiffeners, trapezoidal stiffeners, and top bars were used. Five full-scaled specimens were designed to study the effect of a number of parameters on cyclic performance of connections such as H-section beam size($H-500{\times}200{\times}10{\times}16$, $H-600{\times}200{\times}11{\times}17$), the presence of stiffeners and top bars, and the presence of no weld access hole(WAH) method. Based on the test results, deformation capacity of the specimens with H-500 series beam and H-600 series beam were 4% and 3% rotation angle, which is the requirement for the Special Moment Frame and Intermediate Moment Frame(IMF), respectively. Test result showed that deformation capacity of connection with stiffeners and top bars is greater than that of connection without stiffeners and top bars. Finally, energy dissipation capacity and strain profile of specimens were summarized.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.45 no.2
• /
• pp.128-133
• /
• 2000

This study was carried out to investigate the effect of forms and levels of nitrogen fertilizer on plant growth and essential oil production of Agastache rugosa. Calcium nitrate had more influenced on length and width of leaves and lateral branch length than did urea. When nitrogen fertilizer level was increased from 12 kgN/I0a to 24kgN/I0a, plant growth was stimulated and dry matter of leaf and inflorescence were increased. Top dry matter of plant with calcium nitrate treatment (38.4 g) was heavier than that of urea treatment (32.8 g). Interactions among accession and nitrogen form and nitrogen rate were not significantly different for top dry matter. The forms and rate of nitrogen fertilizer did not affect estragole content. The estragole contents was higher in leaf (91.8%) than that of inflorescence (81.3%). While the essential oil content was not affected by different nitrogen forms, nitrogen level affected the essential oil contents positively by increasing dry matter. Essential oil yield was not affected by accession or nitrogen form, but by nitrogen rate. With increasing N application from 12kgN/I0a to 24 kgN/I0a, essential oil yield was increased by 95.8 %.

• Journal of Microbiology
• /
• v.33 no.4
• /
• pp.315-321
• /
• 1995

The relationship between morphological differentiation and production of trypsin-like protease (TLP_ in streptomycetes was studied. All the Streptomyces spp.In this study produced TLP just before the onset of aerial mycelium formation. Addition of TLP inhibitor, TLCK, to the top surface of colonies inhibited aerial mycelium formation as well as TLP inhibitor, TLCK, to the top surface of colonies inhibited aerial mycelium formation as well as TLP activity. Addition of 2% glucose to the Bennett agar medium repressed both the aerial mycelium formation and TLP production in S. abuvaviensis, S. coelicolor A3(2), S exfoliatus, S. microflavus, S. roseus, s. lavendulae, and S. rochei. However the addition of glucose did not affect S. limosus, S. felleus, S. griseus, S. phaechromogenes, and S. rimosus. The glucose repression on aerial mycelium formation and production of TLP was relieved by the addition of glucose anti-metabolite (methyl .alpha.-glucopyranoside). Therefore, it was concluded that TLP production is coordinately regulated with morphological differentiation and TLP activity is essential for morphological differentiation in streptomycetes. The proposed role of TLP is that TLP participates in the degradation of substrate mycelium protein for providing nutrient for aerial mycelial growth.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.961-963
• /
• 2009

a-Si process-based advanced-SPC (a-SPC) TFT has been developed and verified by manufacturing an AMOLED panel having improved cost competitiveness by using the existing a-Si infrastructure. The a-SPC TFT had superior device reliability and current drivability to a-Si TFT to meet the requirements of AMOLED backplane.