• Advances in concrete construction
• /
• v.9 no.3
• /
• pp.279-287
• /
• 2020

This paper focuses on the engineering properties of Bentonite-Cement-Sodium silicate (BCS) grout, which was prepared by partially replacing the ordinary Portland cement in Cement-Sodium silicate grout with lithium bentonite (Li-bent) and sodium bentonite (Na-bent), respectively. The effect of different Water-to-Solid ratio (W/S) and various replacement percentages of bentonite on the apparent viscosity, bleeding, setting time, and early compressive strength of BCS grout were investigated. The XRD method was used to detect its hydration products. The results showed that both bentonites played a positive role in the stability of BCS grout, increased its apparent viscosity. Na-bent prolonged the setting time of BCS, while 5% of Li-bent shortened the setting time of BCS. The XRD analysis indicated that the hydration products between the mixture containing Na-bent and Li-bent did not differ much. Using bentonite as supplementary cementitious material (SCM) to replace partial cement is a promising way to cut down on carbon dioxide emissions and to produce low-cost, eco-friendly, non-toxic, and water-resistant grout. In addition, Li-bent was superior to Na-bent in improving the strength and the thickening of BCS grouts.

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.561-567
• /
• 2001

It is reported that a lot of sludge powder is produced during the process of manufacturing crushed fine aggregate in mines. However, there is a limitation on the its use that most of them are disposed and wasted, which cause environmental pollution. Therefore, in this paper, tests are carried out in order to recycle sludge powder as filler for cement mortar products. Kinds of aggregates and mix proportion of mortar are varied under various contents of sludge powder. According to test results, it is found that cement mortar products using sludge powder as substitution of fine aggregate about 10% have better qualities than those without sludge powder.

• Cement
• /
• s.64
• /
• pp.11-16
• /
• 1976

암석 파쇄시 최대의 효과를 얻기 위해서는 암석의 물리적, 화학적 특성 및 size 등을 고려하여 최적의 crusher를 선택해야 함을 감안하여 crusher의 일종인 impact crusher의 구조 및 파쇄원리, 파쇄효과, 경제성 검토결과 등을 수록, crusher의 선택 및 광산 운영에 참고케 하고자 한다.

• Journal of the Korea Concrete Institute
• /
• v.16 no.3 s.81
• /
• pp.369-374
• /
• 2004

Calcium sulfoalumiante(CSA) was prepared for using natural calcite($CaCO_3$) and industrial by-products and wastes, such as $Al(OH)_3,\;CaSO_4{\cdot}2H_2O$. The mixture of raw materials was fired at 20, 400, 600, $1200^{\circ}C$ for 1h and cooled rapidly in air. The cement replaced by 10 wt% $C_4A_3S$ expansive additives was investigated by the measurement of the hydration products and compressive strength, setting time, expansion at wet curing condition. $C_4A_3S$ was found in x-ray diffraction pattern over the temperature $1200^{\circ}C$. The setting time or the cement pastes added clinkers fired at different temperature was shorter than ordinary portland cement. The compressive strength was higher than the ordinary portland cement about 20~30%. The mainly hydration products were ettringite, and $Ca(OH)_2$. The expansion due to the formation of ettringite during hydration decreased the drying shrinkage of hardened cement rather than the ordinary portland cement.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.43-44
• /
• 2023

This study evaluated the mechanical and electrical properties of low-cement mortar using a large amount of industrial by-products to reduce carbon emissions from the cement industry. As types of industrial by-products, blast furnace slag and fly ash, which are representative materials, were used, and ultra-high fly ash was mixed and evaluated to solve the problem of initial strength loss. In addition, in order to evaluate the electrical properties, 1% of MWCNT was incorporated relative to the powder mass. As experimental items, the compressive strength was measured on the 1st, 3rd, 7th and 28th days of age, and the rate of change in electrical resistance was measured on the 28th day of age. As a result of the experiment, the initial strength of the test specimen mixed with blast furnace slag and fly ash was significantly lower than that of 100% cement, and the specimen mixed with blast furnace slag showed strength equal to that of cement at 28 days of age. As an electrical characteristic, the electrical resistance was reduced when the load was loaded, and this reason is judged to be the effect of improving the conductivity as the connection between CNTs is narrowed by the compressive load.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.186-187
• /
• 2022

The purpose of this study was to give fluidizing properties to non-sirtered cement made using by-products that can replace Portland cement by using a fluidizing agent. Blast furnace slag, C-type fly ash, and F-type fly ash were used for non-sirtered cement, and sand was used for aggregate. The amount of fluidizing agent used was fixed at 1%, and the water-cement ratio (W/C) was different by setting the binder blending ratio of the non-sintered cement differently, and the fluidity test and flow were compared. As a result of the experiment, when the flow standard was 170mm when the fluidizing agent was used, the fluidizing properties were shown at an average water-cement ratio (W/C) of 36%. Through this study, it was confirmed that the fluidizing properties appeared when the fluidizing agent was used in non-sintered cement.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.27-28
• /
• 2020

In this paper, we investigated the performance of synthetic graphene oxide-functionalized carbon nanotubes (GF) to promote cement hydration and increase the mechanical properties of cement paste. The enhancement effect of GF on the various properties of cement paste was evaluated via the mechanical strength, X-ray diffraction, and heat of hydration of cement paste. The results clearly showed that GF incorporation into cement paste promotes the early hydration of cement paste, generates more hydration products, which results in the mechanical improvement of cement paste. The compressive and splitting tensile strength were increased by 32.17% and 17.31%, respectively, compared to ordinary Portland cement at 28 days of hydration.

• Geomechanics and Engineering
• /
• v.31 no.2
• /
• pp.149-158
• /
• 2022

Ladle furnace (LF) slag, waste from the steel-making process, was incorporated to improve the compressive strength of soil cement. LF slag was mixed to replace the cement in the soil-cement samples with wt% ratio 20:0, 15:5, and 10:10 of cement and slag, respectively. LF slag in the range of 5, 10, and 20 wt% was also separately added to the 20-wt% cement-treated soil samples. The soil-cement mixed LF slag samples were incubated in a plastic wrapping for 7, 14, and 28 days. The strength of soil cement was highly developed to be higher than the standard acceptable value (0.6 MPa) after incorporating slag into soil cement. The mixing of LF slag resulted in more hydration products for bonding soil particles, and hence improved the strength of soil cement. With the LF slag mixing either a replacement or additive materials in soil cement, the LF slag to cement ratio is considered to be less than 1, while the cement content should be more than 10 wt%. This is to promote a predominant effect of cement hydration by preventing the partially absorbed water on slag particles and keeping sufficient water content for the cement hydration in soil cement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1989.10a
• /
• pp.25-30
• /
• 1989

In this paper, morter and concrete specimens made with four cements were immersed in Mgcl2, MgSO4 Solution and artifical Seawater which was corresponded with Seawater. The hydration products of immersed cement pastes were looked over by using SEM, EDS and X-ray diffraction method. The results show that the concrete made with domestic flyash cement and blast-frrnace slag cement is superior to that of ordinary portland cement in resistance to chloride and sulphate solution. Especially, it is found that the attack of Cl-ion on the concrete plays an important role of the deterioration of concrete.

• The Korean Journal of Ceramics
• /
• v.5 no.1
• /
• pp.35-39
• /
• 1999

For many years, alkali activated blast furnace slag cement containing no ordinary portland cement has received much attention in the view of energy saving and its many excellent properties. We examined the structural change of slag glass which was activated by alkali metal compounds using IR spectroscopy. The properties of hydrated products and unhydrated slag grains was characterized by XRD and micro-conduction calorimeter. Ion concentration change in the liquid during the hydration of blast furnace slag was also studied to investigated the hydration mechanism.