• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.4
• /
• pp.357-362
• /
• 2005

The tandem solar cell composed of a dye-sensitized solar cell (DSC) and a thermoelectric generator (TEG) was designed. In such new cell, the characteristics of DSC and TEG were investigated. DSC uses the wavelength range of 380∼750 nm and has the maximum efficiency of below 10 ％. If the solar light transmitted through DSC can be converted to heat energy, TEG can generate electric energy using this heat energy. By this means, it is possible to utilize most of solar energy in the wavelength range of 350∼3000 nm for electric generation and it can be expected to obtain higher solar energy conversion efficiency exceeding the known limit of maximum efficiency. For this purpose we suggest the tandem solar cell constructed with DSC and TEG. In this structure, DSC has a carbon nanotube film as a counter electrode of DSC in order to collect the solar light and convert it to heat energy. We measured the I-V characteristics of DSC and TEG, assembled to the tandem cell. As a result, it was shown that DSC with carbon nanotube and TEG had the efficiency of 9.1 ％ and 6.2 ％, respectively. From this results, it is expected that the tandem solar cell of the new design has the possibility of enhanced conversion efficiency to exceed above 15 ％.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.284-287
• /
• 2017

This paper introduces liquid crystal (LC) alignment and its electro-optical properties in the LC cells with silver nanowire (AgNW) networks. The AgNW network was used as an electrode of LC cell as a substitute for an indium-tin-oxide (ITO) film. LC alignment characteristics in the LC cell using AgNW networks, which have two different sheet resistances of $60{\Omega}/m^2$ and $80{\Omega}/m^2$, were observed. The LC alignment characteristics including pretilt angle, LC alignment state, and thermal stability are similar irrespective of sheet resistance of AgNW network. However, twisted-nematic (TN)-LC cell normally operated when using AgNW network with sheet resistance of $80{\Omega}/m^2$. Electrooptical properties of TN-LC cell exhibited competitive performance compared to those of TN-LC cell based on conventional ITO electrode, which allow new approaches to replace conventional ITO electrode in display technology.

• KSBB Journal
• /
• v.6 no.3
• /
• pp.231-240
• /
• 1991

Recently, developments of large scale and high density cell culture methods have been the objects of many researches, because the demand of various pharmaceutical products produced by animal cell culture has been rapidly increasing. The cell culture equipment should have the requirements such as sufficient oxygen transfer and mixing, low shear stress and surface tension, and small foaming. In order to develop a proper bioreactor meeting these requirements simultaneously, a perfluorocarbon having high solubility of oxygen was sprayed into the medium as an oxygen carrier instead of air. Also, a new impeller was developed and combined together with the perfluorocarbon spraying system so as to design a new bioreartor for cell cultivation. The new impeller had better characteristics of mixing and oxygen transfer than the paddle and cell-lift impellers based on the same, shear rate. But, it was observed that the volumetric oxygen transfer coefficient of the new bioreactor decreased with increasing cell density during E. coli fermentation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.5
• /
• pp.372-376
• /
• 2012

This study focused on the performance characteristics of solar cell using the impedance technique. We measured an impedance according to frequency from 1 Hz until 1 MHz. It could know that the impedance was decreased according to the frequency increases in solar cell. The impedance of single crystal solar cell was 0.61 ${\Omega}$ at 1 Hz, and kept almost settled value to $1{\times}10^2$ Hz. However, the impedance of polycrystal solar cell was $7{\times}10^3{\Omega}$ at 1 Hz.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.157-160
• /
• 2007

The catalyst layer of a proton exchange membrane (PEM) fuel cell is a mixture of polymer, carbon, and platinum. The characteristics of the catalyst layer play critical role in determining the performance of the PEM fuel cell. This research investigates the role of catalyst layer composition using a Central Composite Design (CCD) experiment with two factors which are Nafion content and carbon loading while the platinum catalyst surface area is held constant. For each catalyst layer composition， polarization curves are measured to evaluate cell performance at common operating conditions, Electrochemical Impedance Spectroscopy (EIS), and Cyclic Voltammetry (CV) are then applied to investigate the cause of the observed variations in performance. The results show that both Nafion and carbon content significantly affect MEA performance. The ohmic resistance and active catalyst area of the cell do not correlate with catalyst layer composition, and observed variations in the cell resistance and active catalyst area produced changes in performance that were not significant relative to compositions of catalyst layers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.575-578
• /
• 2004

In this study, we designed HAN(hybrid-aligned nematic) cell using novel tilt angle control method. It was possible to make novel HAN cell using a single polyimide by hot plate baking method. This new HAN cells showed slower response time as compared with conventional HAN cell. However, the alignment state and V-T curve of HAN cell using novel method were acceptable. Also, it showed better C-V characteristic than that of conventional HAN cell.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.510-511
• /
• 2008

Fuel cell is a modular, high efficient and environmentally energy conversion device, it has become a promising option to replace the conventional fossil fuel based electric power plants. The high temperature fuel cell has conspicuous feature and high potential in being used as an energy converter of various fuel to electricity and heat. And, The research and development for the solid oxide fuel cell have been promoted rapidly and extensively in recent years, because of their high efficiency and future potential. Therefore this paper describes the manufacturing method and characteristics of anode electrode for solid oxide fuel cell, by the way, Ni-YSZ materials are used as anode of high temperature widely. So in this experiments, we investigated the optimum content of Ni, by the impedance characteristics, overvoltage. As a result, the performance of Ni-YSZ anode(40vol%) was better excellent than the others.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.523-525
• /
• 2005

In this paper, electronic-controlled power supply(EPS) system for solar cell characteristic is proposed to solve various problems and to achieve reliable experimental result on photovoltaic system. This system emulates the solar cell output characteristics, and it can substitute solar cell in laboratory experiment system. New model for solar cell is proposed to realize the EPS system for solar cell, which is based on the interpolation. Both simulation and experiment are executed to show the validity of the proposed EPS system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.498-501
• /
• 2003

We investigated response characteristics of twisted nematic (TN) cell with different nematic liquid crystals (NLCs) and cell gap d on a rubbed polyimide (PI) surface. High transmittance and fast response time of the TN cell on the rubbed PI surface were achieved by using high birefringence (${\Delta}n$) and low cell gap d. The transmittance and response time of the TN cell on the rubbed PI surface decreased with decreasing ${\Delta}nd$. The fast response time of TN cell using high birefringence with ${\Delta}nd=0.363$ on the rubbed PI surface was measured 5.1 ms.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.206-209
• /
• 2006

In this paper, I try to measure the electrical characteristics of PV cell for lanterns with solar simulator and simulated with PC1D software. I keep my eye on the characteristics variation of PV cell as a temperature change. Therefore, I try to increase a temperature of controlled block from $10^{\circ}C$ to $50^[\circ}C$ while measuring the FV cell. As a result, A variation caused by voltage have an effect on the efficacy of PV cell. Hence it is an important variable when a designer plan to make a solar cell for lanterns.