• Journal of Adhesion and Interface
• /
• v.15 no.1
• /
• pp.22-30
• /
• 2014

Self-photoinitiating acrylate (SPIA) which can undergo self-initiation under UV irradiation was synthesized by a Michael addition in the presence of a base catalyst. The SPIA polymerizations were investigated by photo-differential scanning calorimeter (photo-DSC) and surface physical properties such as pendulum hardness and pencil hardness. The results showed that the SPIA can cure upon UV irradiation by itself without a photoinitiator. But we found out that both the curing rate and the conversion were too low for the self-curing reaction of SPIA. In order to improve the SPIA curing properties, we introduced the SPIA/cationic hybrid system and observed the effects of the addition of commercial free radical type monomer and photoinitiator on the curing behaviors. SPIA/cationic hybrid system was the best suitable to improve the SPIA curing properties. The kinetic analysis indicated that the cationic monomer and photoinitiator apparently accelerated the cure reaction and rate of the hybrid SPIA system, mostly due to the synergistic effect of cationic monomer and photoinitiator increasing the mobility of active species and the generation of reactive species (free radical, cation) during the photopolymerization process. The physical properties showed that, unlike typical free radical system, the hybrid systems did not show oxygen inhibition effect because of cationic reaction on the coating surface.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.4
• /
• pp.587-592
• /
• 2002

Photocrosslinkable chalcone-epoxy compound comprising 1,3-bis-(4-hydroxy-phenyl)-propenone was synthe-sized for fabricating the photo-alignment layer of liquid crystals. Chalcone group was introduced into the main chain unit of the epoxy oligomer. We observed a photodimerization behavior and an optical anisotropy of this material by irradiation of a linearly polarized UV(LP-UV) light. With a trace amount of cationic photoinitiator (TRS-HFA), polymerization of epoxy groups was also conducted at the similar wavelength range used for photodimerization. Linearly polarized UV irradiation on the chalcone-epoxy films with cationic photoinitiator induced optical anisotropy of the film and the resultant film can be used for alignment layers for low molecular weight nematic liquid crystals.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.2
• /
• pp.203-209
• /
• 2017

The propenyl ether-type monomers which are applicable for cationic photo-polymerization were synthesized by the condensation reaction of mono and di-functional alcohol with allyl bromide. To examine photo-curable reactivity, these monomers were combined with cationic photoinitiator to prepare coating composition. As a result, the initial rate of polymerization of POMB in mono propenyl ether type was 10.2, which was relatively lower than BPOB in di-propenyl ethers type. However, POMB containing 1.5mol% photoinitiator almost quantitatively reacted within 90 seconds. In addition, Sulfonium salt type photo-initiators containing long-alkyl group showed good solubility with monomers and apperaed to have comparatively higher rate of polymerization and conversion ratio when applying DPSA and DPST which have high acidity on all monomers.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10a
• /
• pp.1-2
• /
• 2003

Some new synthetic routes for the preparation of poly (isobutyl vinyl ether) (P(IBVE)) having a controllable molar mass with narrow distribution via catalytic or photoinduced living cationic polymerization and their conversion to corresponding PVA have been developed. It was found that the combination of iodomethyl methyl ether (IMME)-zinc iodide is effective in the initiation of the catalytic and the various combinations of diphenyliodonium halides, well known photocationic initiators (DPIX) with zinc halides (ZnX$_2$) are also useful in photoinduced living cationic polymerization of isobutyl vinyl ether (IBVE). Polymerization both in the catalytic and photoinduced systems precede until the full consumption of the monomer and the rate of polymerization increases as the concentration of the catalyst or photoinitiator. The number average molar mass of the resulting polymer is proportional with % conversion, which is determined by the ratio of monomer consumed and the initial values of the catalyst or initiator. The living nature was also confirmed by subsequent monomer addition technique.

• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.857-861
• /
• 1994

UV curable hybrid systems have been investigated in the urethane acrylate based formulations where potentially irritant acrylate monomers have been substituted by vinyl ethers. Generally, among the systems studied, coating properties of hybrid system are superior to those of free radical hut inferior to those of cationic systems. When the content of acrylic oligomer is above 70%, however, hybrid system could render an excellent combination of coating and curing properties which outperforms both cationic and free radical systems. Photo-DSC has been used to follow the progress of crosslinking of various coating systems. Results imply that the critical factors in determining the curing rates of coating formulations are different depending upon the formulation characteristics. In the same type of hybrid formulations, the monomer/oligomer ratio rather than photoinitiator efficiency is the critical factor determining the curing rate of the systems.