• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.91-92
• /
• 2009

본 연구에서는 FRP를 거푸집 및 횡보강 철근 대용으로 사용한 현장타설식 CFFT 교각을 개발하는데 있어 축소모형실험을 통해CFFT 교각에 대한 거동분석 및 내진성능 평가를 수행하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.309-312
• /
• 2006

An experimental study for bond slip behavior of concrete and a FRP plank was used as the both formwork and the tensile reinforcement for a concrete structural member is described. For the FRP plank and the concrete to act as a composite structural member a satisfactory bond at the interface between the smooth surface of the FRP and the concrete must be developed. This study focuses on investigation of the bond slip behavior of sand coated interface between FRP and cast-in-place concrete experimentally.

• Geomechanics and Engineering
• /
• 제36권2호
• /
• pp.145-156
• /
• 2024

The mechanical properties of the concrete-frozen soil interface play a significant role in the stability and service performance of construction projects in cold regions. Current research mainly focuses on the precast concrete-frozen soil interface, with limited consideration for the more realistic cast-in-place concrete-frozen soil interface. The two construction methods result in completely different contact surface morphologies and exhibit significant differences in mechanical properties. Therefore, this study selects silty clay as the research object and conducts direct shear tests on the concrete-frozen soil interface under conditions of initial water content ranging from 12% to 24%, normal stress from 50 kPa to 300 kPa, and freezing temperature of -3℃. The results indicate that (1) both interface shear stress-displacement curves can be divided into three stages: rapid growth of shear stress, softening of shear stress after peak, and residual stability; (2) the peak strength of both interfaces increases initially and then decreases with an increase in water content, while residual strength is relatively less affected by water content; (3) peak strength and residual strength are linearly positively correlated with normal stress, and the strength of ice bonding is less affected by normal stress; (4) the mechanical properties of the cast-in-place concrete-frozen soil interface are significantly better than those of the precast concrete-frozen soil interface. However, when the water content is high, the former's mechanical performance deteriorates much more than the latter, leading to severe strength loss. Therefore, in practical engineering, cast-in-place concrete construction is preferred in cases of higher negative temperatures and lower water content, while precast concrete construction is considered in cases of lower negative temperatures and higher water content. This study provides reference for the construction of frozen soil-structure interface in cold regions and basic data support for improving the stability and service performance of cold region engineering.

• 한국산학기술학회논문지
• /
• 제16권3호
• /
• pp.2279-2286
• /
• 2015

GFRP 판을 영구 거푸집 및 주요 인장 보강재로 활용한 GFRP-콘크리트 하이브리드 구조의 활용에 대해 최근 활발하게 연구가 이루어지고 있다. GFRP 판과 콘크리트 하이브리드 구조의 거동을 이해하기 위해서는 GFRP 판과 현장타설 고강도콘크리트 사이의 정량적인 국부 부착슬립모델이 필요하다. 본 연구에서는 이러한 하이브리드 구조에 간단하게 적용할 수 있는 2중 직선 단순 부착슬립관계를 제안하고자 한다. 본 연구에서 제안된 단순 부착슬립관계의 최대 평균 부착응력은 3.29MPa이며, 초기 기울기는 35.66MPa/mm, 총 슬립은 0.23mm이고 계면 파괴에너지는 0.37kN/m로 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권2호
• /
• pp.59-67
• /
• 2018

기존의 LB-DECK는 레티스바와 현장에서 배근되는 철근과의 간섭이 시공성 등을 저하시키는 문제점이 지적되고 있었다. HB-DECK는 레티스바의 형태를 단순화하고, 방향을 주철근 방향에서 배력근 방향으로 전환하였으며 강성을 증가시키기 위해 하면에 리브를 설치하였다. 본 연구에서는 HB-DECK가 프리캐스트 콘크리트 슬래브로써 성능을 발휘할 수 있는지를 검증하고자 하였다. 이를 위해 도로교설계기준(2015)에 의한 구조검증과 HB-DECK와 현장타설 콘크리트와의 합성거동 분석을 위해 정적재하시험을 수행하였다. 범용구조해석 프로그램인 MIDAS FEA를 이용하여 3차원 유한요소해석을 수행하였으며, 해석결과와 실험결과를 비교분석하였다. 그 결과, HB-DECK는 현장타설 콘크리트와 완전한 합성거동을 하는 것으로 나타났으며, 도로교설계기준(2015)에서 요구하는 구조성능을 만족하는 것으로 나타났다.

• Geomechanics and Engineering
• /
• 제5권2호
• /
• pp.119-142
• /
• 2013

Pile load tests using Osterberg cells (O-cell) were conducted on cast-in-place concrete piles founded in oil sand fill and in situ oil sand at an industrial plant site in Fort McMurray, Alberta, Canada. Interpreted pile test results show that very high pile shaft resistance (with the Bjerrum-Burland or Beta coefficient of 2.5-4.5) against oil sand could be mobilized at small relative displacements of 2-3% of shaft diameter. Finite element simulations based on linear elastic and elasto-plastic models for oil sand materials were used to analyze the pile load test measurements. Two constitutive models yield comparable top-down load versus pile head displacement curves, but very different behaviour in mobilization of pile shaft and end bearing resistances. The elasto-plastic model produces more consistent matching in both pile shaft and end bearing resistances whereas the linear elastic under- and over-predicts the shaft and end bearing resistances, respectively. The mobilization of high shaft resistance in oil sand under pile load is attributed to the very dense and interlocked structure of oil sand which results in high matrix stiffness, high friction angle, and high shear dilation.

• Structural Engineering and Mechanics
• /
• 제36권6호
• /
• pp.745-758
• /
• 2010

12 typical laminated composite reinforced concrete (RC) walls with different concrete ages and 3 cast-in-place RC walls subjected to low frequency cyclic load were carried out in this study. The failure mode, force-deformation response and energy dissipation capacity of these specimens were investigated. Differences of structural behaviours between composite RC walls and common cast-in-place RC walls were emphasized in the analysis. The compatibility of the composite specimens with different concrete ages was discussed based on the experiment. Test results indicated that the differences between the lateral bearing capacity and the displacement ductility of the composite walls and the common walls were not so obvious. Some of the composite specimen even has higher bearing capacity under the experiment loading situation. Besides, the two parts of the laminated composite specimens demonstrates incompatibility at the later loading sequence on failure mode and strain response when it is in tension. Finally, this laminated composite shear walls are suggested to be applied in rapid reconstruction structures which is not very high.

• 한국지열·수열에너지학회논문집
• /
• 제18권2호
• /
• pp.1-9
• /
• 2022

A novel steel-pipe energy pile is introduced, in which the deformed rebars for main reinforcing are replaced with steel pipes in a large diameter cast-in-place energy pile. Here, the steel pipes act as not only reinforcements but also heat exchangers by circulating the working fluid through the hollow hole in the steel pipes. Under this concept, the steel-pipe energy pile can serve a role of supporting main structures and exchanging heat with surrounding mediums without installing additional heat exchange pipes. In this study, the steel-pipe energy pile was constructed in a test bed considering the material properties of steel pipes and the subsoil investigation. Then, the thermal performance test (TPT) in cooling condition was conducted in the constructed energy pile to investigate thermal performance. In addition, the thermal performance of the steel-pipe energy pile was compared with that of the conventional large diameter cast-in-place energy pile to evaluate its applicability. As a result, the steel-pipe energy pile showed 11% higher thermal performance than the conventional energy pile along with much simpler construction processes.

• Steel and Composite Structures
• /
• 제21권5호
• /
• pp.981-997
• /
• 2016

To avoid the cracks of cast-in-place concrete in shear pockets and seams in the traditional composite beam with precast decks, this paper proposed a new type of prefabricated steel truss-concrete composite beam (ab. PSTC beam) with pre-embedded shear studs (ab. PSS connector). To study the initial cracking load of concrete deck, the development and distribution laws of the cracks, 3 PSTC beams were tested under hogging moment. And the crack behavior of the deck was compared with traditional precast composite beam, which was assembled by shear pockets and cast-in-place joints. Results show that: (i) the initial crack appears on the deck, thus avoid the appearance of the cracks in the traditional shear pockets; (ii) the crack of the seam appears later than that of the deck, which verifies the reliability of epoxy cement mortar seam, thus solves the complex structure and easily crack behavior of the traditional cast-in-place joints; (iii) the development and the distribution laws of the cracks in PSTC beam are different from the conventional composite beam. Therefore, in the deduction of crack calculation theory, all the above factors should be considered.

• Structural Engineering and Mechanics
• /
• 제58권1호
• /
• pp.39-58
• /
• 2016

Since the publication of ACI 318-02, the concrete capacity design (CCD) method has been used to determine the resistance of unreinforced concrete anchors. The regulation of steel-reinforced anchors was proposed in ACI 318-08. Until ACI 318-08, the shear resistance of concrete breakout for an unreinforced anchor during an earthquake was reduced to 75% of the static shear strength, but this reduction has been eliminated since ACI 318-11. In addition, the resistance of a hairpin-reinforced anchor was calculated using only the strength of the steel, and a regulation on the dynamic strength was not given for reinforced anchors. In this study, shaking table tests were performed to evaluate the dynamic shear strength of unreinforced and hairpin-reinforced cast-in-place (CIP) anchors during earthquakes. The anchors used in this study were 30 mm in diameter, with edge distances of 150 mm and embedment depths of 240 mm. The diameter of the hairpin steel was 10 mm. Shaking table tests were carried out on two specimens using the artificial earthquake, based on the United States Nuclear Regulatory Commission (US NRC)'s Regulatory Guide 1.60, and the Northridge earthquake. The experimental results were compared to the current ACI 318 and ETAG 001 design codes.