• Archives of Reconstructive Microsurgery
• /
• v.2 no.1
• /
• pp.20-28
• /
• 1993

From 1981 to 1991, twenty one vascularized bone grafts had been performed for the treatment of large bone defects of the extremities, with average follow-up of 65.4 months. Fibulae were used in 15 patients Including two cases of osteocutaneous flap, iliums in 5 including two of osteocutaneous flap, and osteocutneous rib in one. Ten of these patients were treated for segmental defects derived from trauma or infection sequelae of long bones, while eight for locally aggressive benign or malignant bone tumors ; and three for congenital pseudarthrosis of tibia. The location of the lesions were 8 cases in tibia; 7 in humerus ; 3 in forearm bone ; 2 in foot ; and 1 in femur. The length of bone defects were averaged as 10 cm, ranging from 3 to 17.5. In eighteen patients(85.7%), the operation was successful. The duration from operation to bony union was average 5.1 months on successful cases, and three of them needed additional procedures, such as bone graft and electrical stimulation to promote bony union. Local recurrence was found in one case of chondrosarcoma, resulting in AK amputation. Wound infections were noted each one case on donor or recipient site. In five cases, the fracture of grafted bone, which united with cast immobilization in four, occurred average 16.7 months after operation.

• Archives of Reconstructive Microsurgery
• /
• v.6 no.1
• /
• pp.63-72
• /
• 1997

We have evaluated the clinical results following the 46 cases of free vascularized osteocutaneous fibular flap transfer to the tibial defect combined with skin and soft tissue defect, which were performed from May 1982 to January 1997. Regarding to the operation, flap size, length of the grafted fibula, anastomosed vessels, ischemic time of the flap and total operation time were measured. After the operation, time to union of grafted fibula and the amount of hypertrophy of grafted fibula were periodically measured through the serial X-ray follow-up and also the complications and results of treatment were evaluated. In the 46 consecutive procedures of free vascularized osteocutaneous fibular flap transfer, initial bony union were obtained in the 43 grafted fibulas at average 3.75 months after the operation. There were 2 cases in delayed unions and 1 in nonunion. 44 cutaneous flaps among the 46 cases were survived but 2 cases were necrotized due to deep infection and venous insufficiency. One necrotized flap was treated with latissimus dorsi free flap transfer and the other was treated with soleus muscle rotational flap. Grafted fibulas have been hypertrophied during the follow-up periods. The fracture of grafted fibula(15 cases) was the most common complication and occurred at average 9.7 months after the operation. The fractured fibulas were treated with the cast immobilization or internal fixation with conventional cancellous bone graft. In the cases of tibia and fibula fracture at recipient site, the initial rigid fixation for the fibula fracture at recipient site could prevent the fracture of grafted fibula to the tibia.

• Journal of Korea Foundry Society
• /
• v.20 no.5
• /
• pp.344-353
• /
• 2000

In order to find out the casting conditions of the thin wall stainless steel exhaust manifold for automobile, the melt flow and solidification behavior simulated by the Z-CAST program were evaluated, and experimental casting result on the test casting and exhaust manifold of SSC13 alloy were investigated. From the results of this study, it was shown that the calculated results on fluid flow were in good agreement with practical thin wall test castings under the same casting conditions, as pouring metal is austenitic stainless steel(SSC13) and pouring temperature is 1575, 1630, and $1665^{\circ}C$ respectively. That calculated result with designed thin wall exhaust manifold was predicted filling up into the mold cavity, and practical casting was sound. The solidification simulation was predicted shrinkages at the bosses for original exhaust manifold, and designed it without bosses was predicted no defect. Therefore practical exhaust manifold casting was sound and in good agreement with calculated solidification results.

• Journal of Korea Foundry Society
• /
• v.17 no.2
• /
• pp.145-150
• /
• 1997

The striations parallel to the casting direction are the characteristic defects occurring during the unidirectional solidification of nonferrous metals such as pure Al and Sn. It has been known that the defects affect the recrystallization temperature as well as the mechanical and electrical properties of Al. However, it has not been still known about the effect of casting factors such as the casting speed, rod diameter of cast metals, and alloying elements on the occurrence of striations. In the present study, these casting factors affecting the occurrence of striation were investigated by adopting the quantitative examination of striations. Also, the relation between striation defects and feathery grain, which are very similar to the striation defects, was studied.

• Journal of Korea Foundry Society
• /
• v.24 no.2
• /
• pp.94-100
• /
• 2004

Gas porosity which is a common defect in aluminum alloy casting, is also thought to be severer in aluminum alloy castings produced by lost foam process due to the pyrolysis of the polystyrene foam pattern during pouring. Fundamental experiments were carried out to evaluate the effect of process variables such as the melt treatment, the cooling rate and pouring temperature on the density and mechanical properties in A356.2 castings with simple bar shape. The density of grain refined specimen was slightly lower than that of degassed one, but was higher than that of no treated one and that of shot ball packed specimen was higher than the other specimens. The tensile strength and elongation were in the ranges of $200{\sim}230MPa$ and $0.5{\sim}1.5%$ respectively. The density and hardness of lost foam cast specimens decreased with increase in pouring temperature.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.15 no.1
• /
• pp.310-317
• /
• 1995

Crack detection technique by ultrasonics in structures and components made of austenitic stainless steel often loses its reliability due to the material characteristics during inservice inspection of nuclear power plants, especially in the area of detection and sizing in centrifugally cast stainless steel pipings. In order to understand and overcome this problem, computer program for tracing the ultrasonic rays within material has been developed to simulate the process of defect detection within weld. The program simulates through transmission and reflection technique in crack detection of austenitic stainless steel as well as ultrasonic beam propagation through multiple media including stainless steel cladding interface.

• Journal of Korea Foundry Society
• /
• v.41 no.3
• /
• pp.241-251
• /
• 2021

7000-series aluminum alloys are noted for their superior strength compared with other Al alloys, and their billets are generally fabricated by direct-chill (DC) casting. Surface defects in a DC-cast aluminum billet are mainly related to exudation and the meniscus freezing phenomenon, which are influenced by alloy compositions, casting speed, and casting temperature. 7000-series aluminum alloys have a wide freezing range during solidification, which makes it easy for casting defects to occur. In this study, we investigated surface defect evolution in casting billets of Al-8Zn-2Mg-2Cu alloy fabricated by a DC casting process. The billets showed "wavy" or "dotted" surfaces. The wavy surface was formed by meniscus freezing at a lower casting speed (200 mm/min) and temperature (655 ℃). In the wavy surface, refined dendritic cells were observed in a concave region due to the constitutional supercooling caused by meniscus freezing. Meanwhile, at a higher casting temperature (675 ℃), the dotted surface was formed by pore formation. In the dotted surfaces in the billet formed at a high casting speed (230 mm/min), an exudation layer was formed by the high metallostatic head pressure. The dotted region and the smooth region had a refined dendritic morphology and a columnar morphology at the exudation layer, respectively. This is attributed to the formation of gas pores in the dotted region.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.1
• /
• pp.109-128
• /
• 2022

The precise inspection for safety and diagnosis (PISD) of tunnel has been conducted by the special act on safety control of public structures. However, the present assessment for the segmental lining of TBM tunnel has limitation such as: NDTs for integrity, segmental configuration for field inspection, and consideration for jacking system. Even if the number of TBM tunnel is less than 1% of enrolled facility in FMS, more attention to maintenance should be necessary due to its usage such as multi-use facility and national important facility. Compared to NATM tunnel, excavated by drilling and blasting and then installed lining by cast-in-place within 6~12 m, TBM tunnel is cut out ground by disk and cutter-bit and then assembled 7 pieces of precast segment, 1.2~1.4 m wide. Different features of design, construction, and maintenance should be considered to be more exact evaluation of TBM tunnel. The characteristics of defect is categorized and analyzed with 11 operational TBM tunnels in domestic subway. To be more comprehend various particular defects, foreign studies have been also adapted. Crack and leakage are categorized in 7 patterns. Breakage/spalling and corrosion are also grouped into 3 patterns. Patterned defects or damages are fed back in design, construction, and are useful guidelines for maintenance stage in future.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.162-173
• /
• 1996

Dry magnetic particle inspection(MPI) was performed to detect the surface defects of steel ingot cast billets. Magnetic properties of several materials were characterized by the measurement of the B-H hysteresis curve. The inspection results were evaluated in terms of the magnetizing current, temperature, and the amount of magnetic particles applied to billets. Magnetic flux leakage near the defect site of interest was measured and compared with the results of calculation by the finite element method in the case of direct magnetizing current. Direct and alternating magnetizing currents for materials were deduced by the comparison of the inspections. Results of the magnetic particle inspection by direct magnetizing current were compared with those of finite element method calculations, which were verified by measuring magnetic leakage flux above the surface and the surface defects of the material. For square rods, due to the geometrical effect, the magnetic flux density at the edges along the length of the rods was about 30% of that at the center of rod face for a sufficiently large direct magnetizing current, while it was about 70% for an alternating magnetizing current. Thus, an alternating magnetizing current generates rather uniform magnetic flux density over the rods, except for the region on the face across about 10 mm from the edge. The attraction of the magnetic particle by the magnetic leakage field was nearly independent of the surface temperature of the billets up to $150^{\circ}C$. However, the temperature should have been limited below $60^{\circ}C$ for an effective fixing of gathered magnetic particles to the billet surface using methylene chloride. We also found that the amount of applied magnetic particles tremendously affected the detection capability.

• Journal of Korea Foundry Society
• /
• v.41 no.5
• /
• pp.434-444
• /
• 2021

This study investigated the overall dependence of the tensile properties of Al-Si alloys on the distribution aspect of a eutectic Si particle in terms of defect susceptibility to the effective void area fraction, referring to the sum of pre-existing microvoids and the damage evolution of the Si particle. The network morphology of as-cast Al-xSi (x=2,5,8,11) alloys was modified to a granular type via a T4 treatment, after which a computational topography (CT) analysis and scanning electron microscope (SEM) observations were utilized to evaluate the size and distribution of the microvoids. The CT and SEM analyses indicated that the main cracks grow along local regions that possess the highest porosity level. The local plastic deformation around the microvoids and the distribution aspect of the microvoids induced a practical difference between the iso-volumetric CT measurement and the SEM fractography outcomes. The results demonstrated that the overall dependence of the ultimate tensile strength (UTS) and elongation on the effective void area fraction is more sensitive to the variation of the area fraction of the Si particle in the network morphology than in the granular type; this is due to the sequential damage evolution of the neighboring Si particles in the eutectic Si colony.