• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.131-138
• /
• 1997

Silicon carbide films were chemically vapor deposited onto graphite substrates using MTS(Ch3SiCl3) as a source and Ar or H2 as a diluent gas. The experiments were performed at a fixed condition such as a de-position temperature of 130$0^{\circ}C$, a total pressure of 10 torr, and a flow rate of 100 sccm for each MTS and carrier gas. The purpose of this study is to consider the variation of the growth behavior with the addition of each diluent gas. It is shown that the deposition rate leads to maximum value at 200 sccm addition ir-respective of diluent gases and the deposition rate of Ar addition is faster than that of H2 one. It seems that these characteristics of deposition rate are due to varying interrelationship between boundary layer thick-ness and the concentration of a source with each diluent gas addition, when overall deposition rate is con-trolled by mass transport kinetics. The preferred orientation of (220) plane was maintained for the whole range of Ar addition. However, above 200 sccm addition, especially that of (111) plane was more increased in proportion to H2 addition. Surface morphologies of SiC films were the facet structures under Ar addition, but those were gradually changed from facet to smooth structures with H2 addition. Surface roughness be-came higher in Ar, but it became lower in H2 with increasing the amount of diluent gas.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.829-838
• /
• 2007

The stochiometric mix of evaporating materials for the $CdGa_2Se_4$ single crystal thin films was prepared from horizontal furnace. To obtain the single crystal thin films, $CdGa_2Se_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperature were $630^{\circ}C$ and $420^{\circ}C$, respectively. The crystalline structure of single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD).The carrier density and mobility of $CdGa_2Se_4$ single crystal thin films measured from Hall effect by van der Pauw method are $8.27{\times}10^{17}\;cm^{-3},\;345\;cm^2/V{\cdot}s$ at 293 K. respectively. The temperature dependence of the energy band gap of the $CdGa_2Se_4$ obtained from the absorption spectra was well described by the Varshni's relation, $Eg(T)\;=\;2.6400\;eV\;-\;(7.721{\times}10^{-4}\;eV/K)T^2/(T+399\;K)$. After the as-grown single crystal $CdGa_2Se_4$ thin films were annealed in Cd-, Se-, and Ga -atmospheres, the origin of point defects of single crystal $CdGa_2Se_4$ thin films has been investigated by PL at 10 K. The native defects of $V_{Cd}$, $V_{Se}$, $Cd_{int}$, and $Se_{int}$ obtained by PL measurements were classified as donors or accepters. We concluded that the heat-treatment in the Cd-atmosphere converted single crystal $CdGa_2Se_4$ thin films to an optical p-type. Also, we confirmed that Ga in $CdGa_2Se_4/GaAs$ did not form the native defects because Ga in single crystal $CdGa_2Se_4$ thin films existed in the form of stable bonds.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.219-226
• /
• 2013

Organic semiconductor-based soft electronics has potential advantages for next-generation electronics and displays, which request mobile convenience, flexibility, light-weight, large area, etc. Organic field-effect transistors (OFET) are core elements for soft electronic applications, such as e-paper, e-book, smart card, RFID tag, photovoltaics, portable computer, sensor, memory, etc. An optimal multi-layered structure of organic semiconductor, insulator, and electrodes is required to achieve high-performance OFET. Since most organic semiconductors are self-assembled structures with weak van der Waals forces during film formation, their crystalline structures and orientation are significantly affected by environmental conditions, specifically, substrate properties of surface energy and roughness, changing the corresponding OFET. Organo-compatible insulators and surface treatments can induce the crystal structure and orientation of solution- or vacuum-processable organic semiconductors preferential to the charge-carrier transport in OFET.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.122-122
• /
• 1999

Graphite with its advantages of high thermal conductivity, low thermal expansion coefficient, and low elasticity, has been widely used as a structural material for high temperature. However, graphite can easily react with oxygen at even low temperature as 40$0^{\circ}C$, resulting in CO2 formation. In order to apply the graphite to high temperature structural material, therefore, it is necessary to improve its oxidation resistive property. Silicon Carbide (SiC) is a semiconductor material for high-temperature, radiation-resistant, and high power/high frequency electronic devices due to its excellent properties. Conventional chemical vapor deposited SiC films has also been widely used as a coating materials for structural applications because of its outstanding properties such as high thermal conductivity, high microhardness, good chemical resistant for oxidation. Therefore, SiC with similar thermal expansion coefficient as graphite is recently considered to be a g행 candidate material for protective coating operating at high temperature, corrosive, and high-wear environments. Due to large lattice mismatch (~50%), however, it was very difficult to grow thick SiC layer on graphite surface. In theis study, we have deposited thick SiC thin films on graphite substrates at temperature range of 700-85$0^{\circ}C$ using single molecular precursors by both thermal MOCVD and PEMOCVD methods for oxidation protection wear and tribological coating . Two organosilicon compounds such as diethylmethylsilane (EDMS), (Et)2SiH(CH3), and hexamethyldisilane (HMDS),(CH3)Si-Si(CH3)3, were utilized as single source precursors, and hydrogen and Ar were used as a bubbler and carrier gas. Polycrystalline cubic SiC protective layers in [110] direction were successfully grown on graphite substrates at temperature as low as 80$0^{\circ}C$ from HMDS by PEMOCVD. In the case of thermal MOCVD, on the other hand, only amorphous SiC layers were obtained with either HMDS or DMS at 85$0^{\circ}C$. We compared the difference of crystal quality and physical properties of the PEMOCVD was highly effective process in improving the characteristics of the a SiC protective layers grown by thermal MOCVD and PEMOCVD method and confirmed that PEMOCVD was highly effective process in improving the characteristics of the SiC layer properties compared to those grown by thermal MOCVD. The as-grown samples were characterized in situ with OES and RGA and ex situ with XRD, XPS, and SEM. The mechanical and oxidation-resistant properties have been checked. The optimum SiC film was obtained at 85$0^{\circ}C$ and RF power of 200W. The maximum deposition rate and microhardness are 2$mu extrm{m}$/h and 4,336kg/mm2 Hv, respectively. The hardness was strongly influenced with the stoichiometry of SiC protective layers.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.5
• /
• pp.179-186
• /
• 2007

Single crystal $CdGa_2Se_4$ layers were grown on a thoroughly etched semi-insulating GaAs(100) substrate at $420^{\circ}C$ with the hot wall epitaxy(HWE) system by evaporating the polycrystal source of $CdGa_2Se_4$ at $630^{\circ}C$. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction(DCXD). The carrier density and mobility of single crystal $CdGa_2Se_4$ thin films measured with Hall effect by van der Pauw method are $8.27{\times}10^{17}cm^{-3},\;345cm^2/V{\cdot}s$ at 293 K, respectively. The photocurrent and the absorption spectra of $CdGa_2Se_4/SI$(Semi-Insulated) GaAs(100) are measured ranging from 293 K to 10 K. The temperature dependence of the energy band gap of the $CdGa_2Se_4$ obtained from the absorption spectra was well described by the Varshni's relation $E_g(T)=2.6400eV-(7.721{\times}10^{-4}eV/K)T^2/(T+399K)$. Using the photocurrent spectra and the Hopfield quasicubic model, the crystal field energy(${\Delta}cr$) and the spin-orbit splitting energy(${\Delta}so$) far the valence band of the $CdGa_2Se_4$ have been estimated to be 106.5 meV and 418.9 meV at 10 K, respectively. The three photocurrent peaks observed at 10 K are ascribed to the $A_{1^-},\;B_{1^-},\;and\;C_{11}-exciton$ peaks.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.646-651
• /
• 2018

This paper reports that the electronic properties at a $P3HT/TiO_2$ interface associated with exciton dissociation and transport can be tailored by the insertion of a graphene quantum dot (GQD) layer. For donor/acceptor interface modification in an $ITO/TiO_2/P3HT/Al$ photovoltaic (PV) device, a continuous GQD film was prepared by a sonication treatment in solution that simplifies the conventional processes, including laser fragmentation and hydrothermal treatment, which limits a variety of component layers and involves low cost processing. The high conductivity and favorable energy alignment for exciton dissociation of the GQD layer increased the fill factor and short circuit current. The origin of the improved parameters is discussed in terms of the broad light absorption and enhanced interfacial carrier transport.

• The Research Journal of the Costume Culture
• /
• v.16 no.6
• /
• pp.1050-1063
• /
• 2008

A movie is a fiction made on a basis of an author's and a writer's imagination, but all sorts of properties mixed with each other and most realistically expresses the era which becomes the background of a movie and acts as a carrier that connects designers with consumers. Thus, this study was carried out to review how the fashion products that designer's intention and commercial value added are expressed in collections by comparing and analysing the costumes in the movie "The Great Gatsby" that described the life of America's upper-class in 1920s and the 04 S/S Y&Kei collection which were proceeding after getting inspiration from this movie. For this, literature materials were inspected in order to make a theoretical review on social and cultural background and costumes history background in 1920s and the photo materials on movie costume were collected and analysed using DVD video captures, as well as the photo materials on 04 S/S Y&Kei were collected and analyzed through the institute providing domestic fashion information. The following conclusion was deduced through this study. First, in 1920s which becomes the background of this study, the slim shape of Flapper which looks like a young and boy became an ideal figure condition and the straight silhouette with low waist line and the short skirt that rose to knee was popular. Second, as a result of analysing movie costume by classifying it in silhouette, colors, and materials, straight silhouette of low waistline with a near colored - tone seen in the pastel series, including white, beige, pink, and gray was mainly constituted and the metal colors like silver and gold were used. As a material, chiffon, satin, velvet, flower patterned prints, and beads were used, which represented luxurious life of women in the upper classes. Third, as a result of comparing and analysing, it turned out that there was a similarity. However, in dress collection for a heroine, some dissimilarity differentiated from a movie costumes was found out in that the dresses in collection expressed moderate beauty and modernism and elegant beauty at the same time by matching a variety of materials and using black color.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.337-337
• /
• 2014

투명 전도성 산화물(transparent conductive oxide: TCO) 박막은 높은 투과율과 낮은 비저항 덕분에 LCD (liquid crystal display), PDP (plasma display panel), OLED (organic light emitting display) 등 평판 디스플레이에 널리 사용되고 있다. 현재 양산되고 있는 ITO (indium tin oxide)는 90% 이상의 높은 투과율과 우수한 전도성으로 인해 TCO 박막 가운데서 디스플레이 산업에서 가장 널리 쓰이고 있다. 그런데, ITO의 인듐산화물에 의한 간질성 폐렴(interstitial pneumonia)의 유발 위험이 있다든가, 인듐의 매장량이 적어 원자재 가격이 비싼 단점도 가지고 있다. 이에 최근 ITO를 대체할 수 있는 TCO물질로 많은 연구가 이루어지고 있는데, 특히 AZO (aluminum-doped zinc oxide)는 그 중 대표적인 대체물질로서 독성이 없고 가격도 저렴하여 많은 관심이 증폭되고 있다. 현재 AZO는 sol-gel 방법이나 CVD (chemical vapor deposition) 또는 스퍼터링 방법 등으로 증착되고 있다. 본 연구에서는 두 개의 이종타겟(hetero target)을 장착한 대향 타겟 스퍼터링(facing target sputtering: FTS) 장치를 사용하여 AZO 박막을 제작한다. 기존의 여러 증착법과 달리, FTS 장치는 두 타겟 사이에 형성되는 플라즈마 내의 ${\gamma}$-전자를 구속하게 되며, 낮은 가스 압력에서 고밀도 플라즈마가 생성되어 빠른 증착 속도와 안정적인 방전을 유지한 상태에서 박막을 증착할 수가 있다. 또한 기판과 플라즈마가 이격되어 있어 높은 에너지를 갖는 입자들의 기판 충돌을 억제할 수 있는 장점들을 갖는다. 이종 타겟인 ZnO와 Al2O3를 사용하고 각 타겟에 인가되는 파워 변화를 통해 AZO 박막 내 Al2O3의 성분비를 조절하였다. ZnO 타겟의 증착 파워를 100 W로 고정할 경우, Al2O3 타겟의 증착 파워가 (50~90) W으로 실험을 하였으며, Al2O3 타겟의 증착 파워가 70 W일 때 AZO 박막의 Al2O3 성분비는 2.02 wt.%이며 박막의 비저항 값은 $5{\times}10^{-4}{\Omega}{\cdot}cm$로 최소값을 보였다. 이러한 비저항의 변화는 파워에 따른 AZO 박막의 캐리어 이동도(Hall mobility)와 캐리어의 농도(Carrier Concentration)의 변화와 밀접한 관계가 있음을 보여주며, 특히 AZO 박막의 캐리어 농도와 캐리어 이동도는 AZO 박막을 형성하고 있는 결정립의 크기에 의존하는 것이 X-선 회절 패턴과 SEM으로부터 확인되었다. 특히, 본 연구에서는 두 개의 이종 타겟(hetero target) Al2O3와 ZnO를 장착하고 각각의 파워를 변화시켜 도핑 량을 조절할 수는 대향 타겟 스퍼터링(FTS: facing-target sputtering) 방법을 이용하여 제작된 AZO 박막에 대해 전기적, 광학적 및 구조적 특성을 분석하고 ITO의 대체물로서의 가능성을 검토하고자 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.335-335
• /
• 2014

Over the past several years, transparent conducting oxides have been extensively studied in order to replace indium tin oxide (ITO). Here we report on fluorine doped zinc tin oxide (FZTO) films deposited on glass substrates by radio-frequency (RF) magnetron sputtering using a 30 wt% ZnO with 70 wt% SnO2 ceramic targets. The F-doping was carried out by introducing a mixed gas of pure Ar, CF4, and O2 forming gas into the sputtering chamber while sputtering ZTO target. Annealing temperature affects the structural, electrical and optical properties of FZTO thin films. All the as-deposited FZTO films grown at room temperature are found to be amorphous because of the immiscibility of SnO2 and ZnO. Even after the as-deposited FZTO films were annealed from $300{\sim}500^{\circ}C$, there were no significant changes. However, when the sample is annealed temperature up to $600^{\circ}C$, two distinct diffraction peaks appear in XRD spectra at $2{\Theta}=34.0^{\circ}$ and $52.02^{\circ}$, respectively, which correspond to the (101) and (211) planes of rutile phase SnO2. FZTO thin film annealed at $600^{\circ}C$ resulted in decrease of resistivity $5.47{\times}10^{-3}{\Omega}cm$, carrier concentration ~1019 cm-3, mobility~20 cm2 V-1s-1 and increase of optical band gap from 3.41 to 3.60 eV with increasing the annealing temperatures and well explained by Burstein-Moss effect. Change of work function with the annealing temperature was obtained by ultraviolet photoemission spectroscopy. The increase of annealing temperature leads to increase of work function from ${\phi}=3.80eV$ (as-deposited FZTO) to ${\phi}=4.10eV$ ($600^{\circ}C$ annealed FZTO) which are quite smaller than 4.62 eV for Al-ZnO and 4.74 eV for SnO2. Through X-ray photoelectron spectroscopy, incorporation of F atoms was found at around the binding energy of 684.28 eV in the as-deposited and annealed FZTO up to 400oC, but can't be observed in the annealed FZTO at 500oC. This result indicates that F atoms in FZTO films are loosely bound or probably located in the interstitial sites instead of substitutional sites and thus easily diffused into the vacuum from the films by thermal annealing. The optical transmittance of FZTO films was higher than 80% in all specimens and 2-3% higher than ZTO films. FZTO is a possible potential transparent conducting oxide (TCO) alternative for application in optoelectronics.

• Journal of Sensor Science and Technology
• /
• v.7 no.1
• /
• pp.67-72
• /
• 1998

The crystallized CuPc and PbTe films are formed by thermal evaporation and pulsed ArF excimer laser ablation. Structural and electrical properties of thin film is observed by XRD and current-voltage(I-V) curves. From XRD analysis, both PbTe and CuPc thin films show a-axis oriented structure. For the measurement of photovoltaic effect, the transverse current-voltage curve of CuPc/Si, PbTe/Si and PbTe/CuPc/Si junctions have been analyzed in the dark and under illumination. The PbTe/CuPc/Si junction exthibits a strong photovoltaic characteristics with short circuit current($J_{sc}$) of $25.46\;mA/cm^{2}$ and open-circuit voltage($V_{oc}$) of 170 mV. Quantum efficiency and power conversion efficiency are calculated to be 15.4% and $3.46{\times}10^{-2}$, respectively. Based on the results of QE and ${\eta}$, the photocurrent process of PbTe/CuPc/Si junction can be explained as following three effective steps; photocarrier generation in the CuPc layer, carrier separation at PbTe/CuPc interface, and finally a transportation of electrons through the PbTe layer.