• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2022년도 봄 학술논문 발표대회
• /
• pp.174-175
• /
• 2022

The blast furnace slag, which is widely used as a cement admixture, has latent hydraulics under the influence of cement hydrate, and fly ash and silica fume mainly cause a pozolane reaction. As a result, the cement structure becomes dense, and it is possible to compensate for defects when concrete is usually made with portland cement alone. When fixing carbon dioxide through reaction with carbon dioxide, the amount of calcium hydroxide in the cement paste is important. The larger the amount of calcium hydroxide, the more active the reaction may occur. It is also an important variable in calculating the depth of neutralization through carbonization. In this study, calcium hydroxide in cement paste using mixed materials was quantified through thermal analysis.

• Journal of Ecology and Environment
• /
• 제41권12호
• /
• pp.336-344
• /
• 2017

Background: Because of climate change, interest in the development of carbon pools has increased. In agricultural ecosystems, which can be more intensively managed than forests, measures to control carbon dioxide ($CO_2$) emission and absorption levels can be applied relatively easily. However, crop residues may be released into the atmosphere by decomposition or combustion. If we can develop scientific management techniques that enable these residues to be stocked on farmland, then it would be possible to convert farmlands from carbon emission sources to carbon pools. We analyzed and investigated soil respiration (Rs) rate characteristics according to input of carbonized residue of red peppers (Capsicum annuum L.), a widely grown crop in Korea, as a technique for increasing farmland carbon stock. Results: Rs rate in the carbonized biomass (CB) section was $226.7mg\;CO_2\;m^{-2}h^{-1}$, which was 18.1% lower than the $276.9mg\;CO_2\;m^{-2}h^{-1}$ from the red pepper residue biomass (RB) section. The Rs rate of the control was $184.1mg\;CO_2\;m^{-2}h^{-1}$. In the following year, Rs in the CB section was $204.0mg\;CO_2\;m{-2}h^{-1}$, which was 38.2% lower than the $330.1mg\;CO_2\;m^{-2}h^{-1}$ from the RB section; the control emitted $198.6mg\;CO_2\;m^{-2}h^{-1}$. Correlation between Rs and soil temperature ((Ts) at a depth of 5 cm) was $R^2=0.51$ in the RB section, which was higher than the other experimental sections. A comparison of annual decomposition rates between RB and CB showed a large difference, 41.4 and 9.7%, respectively. The results showed that carbonization of red pepper residues reduced the rates of decomposition and Rs. Conclusions: The present study confirmed that the Rs rate can be reduced by carbonization of residue biomass and putting it in the soil and that the Rs rate and Ts (5 cm) were positively correlated. Based on the results, it was determined that approximately $1.2t\;C\;ha^{-1}$ were sequestered in the soil in the first year and $3.0t\;C\;ha^{-1}$ were stored the following year. Therefore, approximately $1.5t\;C\;ha^{-1}year^{-1}$ are expected to be stocked in the soil, making it possible to develop farmlands into carbon pools.

• Journal of the Korean Wood Science and Technology
• /
• 제50권4호
• /
• pp.256-271
• /
• 2022

Activated carbon (AC) derived from coconut shells (CS-AC) was obtained through pyrolysis at 700℃ and subsequently activated with H₃PO₄. AC was ground in a Wiley mill several times to form powder particles at particle scales of 80, 100, and 200 meshes. The characterization of the AC was studied using scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), Fourier-transform infrared spectroscopy (FT-IR), and surface area analysis (S_BET). The CS-AC-200 mesh resulted in a higher percentage of mesopores and surface area. This particle size had a larger surface area with angular, irregular, and crushed shapes in the SEM view. The smaller particles had smoother surfaces, less wear, and increased curing depth and ratio of the hardness of the resin composite. Based on the characterization results of the AC, it is evident that CS-AC with a 200 mesh particle size has the potential to be used as a filler in biocomposites.

• 전기학회논문지
• /
• 제60권6호
• /
• pp.1274-1279
• /
• 2011

The purpose of this paper is to present the manufacturing defect and damage pattern of a 3 phase 22.9/3.3kV oil immersed transformer, as well as to present an objective basis for the prevention of a similar accident and to secure data for the settlement of PL related disputes. It was found that in order to prevent the occurrence of accidents to transformers, insulating oil analysis, thermal image measurement, and corona discharge diagnosis, etc., were performed by establishing relevant regulation. The result of analysis performed on the external appearance of a transformer to which an accident occurred, the internal insulation resistance and protection system, etc., showed that most of the analysis items were judged to be acceptable. However, it was found that the insulation characteristics between the primary winding and the enclosure, those between the ground and the secondary winding, and those between the primary and secondary windings were inappropriate due to an insulating oil leak caused by damage to the pressure relief valve. From the analysis of the acidity values measured over the past 5 years, it is thought that an increase in carbon dioxide (CO2) caused an increase in the temperature inside the transformer and the increase in the ethylene gas increased the possibility of ignition. Even though 17 years have passed since the transformer was installed, it was found that the system's design, manufacture, maintenance and management have been performed well and the insulating paper was in good condition, and that there was no trace of public access or vandalism. However, in the case of transformers to which accidents have occurred, a melted area between the upper and the intermediate bobbins of the W-phase secondary winding as well as between its intermediate and lower bobbins. It can be seen that a V-pattern was formed at the carbonized area of the transformer and that the depth of the carbonization is deeper at the upper side than the lower side. In addition, it was found that physical bending and deformation occurred inside the secondary winding due to non-uniform pressure while performing transformer winding work. Therefore, since it is obvious that the accident occurred due to a manufacturing defect (winding work defect), it is thought that the manufacturer of the transformer is responsible for the accident and that it is lawful for the manufacture to investigate and prove the concrete cause of the accident according to the Product Liability Law (PLL).