• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.153-153
• /
• 2010

The world is moving towards a post-carbon society and needs clean and renewable energy for sustainable development. There are many methodological approaches which are helping this shift based on analyzed data about energy resources and which focus on limited types of energy including liquid fossil, solid fossil, gaseous fossil, and biomass (e.g. IPCC Guidelines, ISO 14064-1, WRI Protocol, etc.). We should also consider environmental impact (e.g. greenhouse gas emissions, water use, etc.) and the economic cost of the renewable energy to make a better decision. Recently, researchers have addressed the environmental impact of new technologies which include photovoltaics, wind turbines, hydroelectric power, and biofuel. In this work, we analyze the environmental impact with a carbon emission factor to present a correlation between $CO_2$ emission and the cost of energy resources standardized by the energy output. In addition, we reviewed Life Cycle Assessment (LCA) as another methodology. Researchers who are studying energy systems have ignored the impacts of entire energy systems, e.g. the extraction and processing of fossil fuels. In power sector, the assessment should include extraction, processing, and transportation of fuels, building of power plants, production of electricity, and waste disposal. Therefore LCA could be more suitable tool for energy cost and environmental impact estimation.

• Journal of environmental and Sanitary engineering
• /
• v.18 no.2
• /
• pp.87-93
• /
• 2003

This study carried out to recommend adaptable technologies and countermeasures for performance improvement of Wet Scrubber(WS) in industrial waste incinerator. When not using the Activated Carbon(AC), the removal efficiency of dust and HCl is 73%, 92%. And particulate phase and gaseous phase dioxins removal efficiency was evaluated up to 31% and 12%. In this case, dioxins enrichment was not revealed in WS. When using the AC mixing with scrubbing water, the case of 1,000ppm, removal efficiency of particulate phase dioxins was about 51%, and gaseous phase dioxins was about 96%. The case of 2,000ppm, removal efficiency of particulate phase dioxins was about 55%, and gaseous phase dioxins was about 97%. And the case of 3,500ppm, the removal efficiency of particulate phase dioxins was about 35%, and gaseous phase dioxins was about 96% respectively. By this study, using the AC was more useful to remove the gaseous phase dioxins, and needed to use proper concentration of the AC, that in case of 3,500ppm, the particulate phase dioxins removal efficiency was more lower than other cases.

• 한국생물공학회:학술대회논문집
• /
• 2001.11a
• /
• pp.529-532
• /
• 2001

Korean food waste, one of the abundantly available but environmentally problematic organic wastes in Korea, was utilized as solid-substrate by fungal strain Aspergillus niger ATcC 6275 for the production of enzymemixture containing amylase, cellulase and xylanase. The enzyme mixture can be used as high value-added animal feed. Solid-state fermentation method yielded a 84-fold enhancement in xylanase activity compared with submerged fermentation method. The effect of incubation period, incubation temperature, pH of medium, moisture content, inoculum size and enrichment of the medium with nitrogen and carbon sources were observed for optimal production of these enzymes The optimal amylase activity of 33.10 U/g, cellulase activity of 24.41 U/g, xylanase activity of 328.84 U/g were obtained at 8 days incubation with 50%(w/w) soy bean flake, with incubation temperature of $25^{\circ}C$, pH of 6.38, optimal moisture content of 55% and with inoculum size of $3.8{\times}10^6$spore/g. Enzyme activities were enhanced when ImM $CaSO_4$, 2% Malt extract and 2% galactose were added as mineral, nitrogen and carbon enrichment respectively.

• Resources Recycling
• /
• v.10 no.3
• /
• pp.29-36
• /
• 2001

Cyclic voltammetry has been applied in the basic studies for the treatment and recovery of heavy metal component contained in wastewater by electrochemical reduction. The electrochemical behaviors of zinc ion for zinc metal electrode and carbon elec-trode were characterized by voltammograms and it was showed that zinc ions were reduced to metallic form below -0.76 V vs SHE. The change in the features of crystalline form of metallic zinc upon oxidation and reduction reaction was observed by X-ray diffraction method and the Am analysis verified that zinc ions were reduced to metal on copper plate. The results of this study were regarded to be important and meaningful in the treatment of heavy metal containing wastewater and, as a result, in the obtainment of metallic product by electrochemical method.

• Journal of Environmental Health Sciences
• /
• v.27 no.1
• /
• pp.36-43
• /
• 2001

Chitosans were prepared from red crab chitin under various alkali treatment conditions(different alkali concentrations, reaction times and temperatures) and theirphysicochemical properties were investigated. The nitrogen content and deacetylation degree of red crab chitin were 6.15% and 22.17A%, respectively. By the IR spectra, red crab and reference chitin showed the sharp bands at 1650 $cm^{-1}$ / and 1550 $cm^{-1}$ /, which are characteristic of chitin. The nitrogen contents of prepared chitosans ranged from 6.19~7.48%. Thedeacetylation degree was increased from 63~76% and 48~78% with increasing reaction time and temperature, whereas viscosity was decreased. The nitrogen content and yield of red crab chitosan perpared from chitin with 50% NaOH, 1:25(w/v) for 3.0 hr at 120$cm^{-1}$ / were 7.26% and 85.0%, respectively. and viscosity, deacetylation degree and molecular weight, 67.0 mPa.s, 75.0% and 6.5$\times$10$^{5}$ Dalton, respectively. From the IR spectra, the amide absorption bands of red crab and reference chitosan became very weak, similarly. And at solid state $^{13}$ C-NMR spectra, C=O(carbonyl carbon) signals absent, whereas $CH_3$(methyl carbon) was residues. Chemical shift of $^{13}$ C-NMR spectra of red crab and reference chitosans were in good agreement with slight experimental deviation.

• Journal of Energy Engineering
• /
• v.27 no.3
• /
• pp.57-62
• /
• 2018

The development of coal-fired power plants to ensure energy security and electricity consumption is a matter for the Vietnam economy. However, the huge amount of ash discharged is a major environmental challenge. It is estimated that by the end of 2017, the amount of ash in the country is about 40 million tons and annually emitted over 16.4 million tons. While the quantity of coal-fired power plant is rising, the ash content will increase year by year if the ash doesn't treat well. The ash will be increased from 61 million tons in 2018 to 109 million tons in 2020, 248 million tons in 2025 and 422 million tons in 2030. The difficulties of coal-fired power plants are the problem of ash handling, some plants are at risk of closure because there are not enough dump capacity to storage. Therefore, Vietnam is in need of urgent measures to treat a large amount of waste from coal-fired power plants. The specific objectives of this study were as follows: (1) provide an overview of coal ash situation produced by coal-fired power plants in Vietnam; (2) study about regulations related to coal ash treatment; (3) comprehend the literature review of the cement sector status.

• Journal of Energy Engineering
• /
• v.29 no.3
• /
• pp.50-56
• /
• 2020

Currently, 3D printing technology is a new revolutionary additive manufacturing process that can be used for making three dimensional solid objects from digital films. In 2019, this 3D printing technology spreading vigorously in production parts (57%), bridge production (39%), tooling, fixtures, jigs (37%), repair, and maintenance (38%). The applications of 3D printing are expanding to the defense, aerospace, medical field, and automobile industry. The raw materials are playing a key role in 3D printing. Various additive materials such as plastics, polymers, resins, steel, and metals are used for 3D printing to create a variety of designs. The main advantage of the green cement for 3D printing is to enhance the mechanical properties, and durability to meet the high-quality material using in construction. There are several advantages with 3D printing is a limited waste generation, eco-friendly process, economy, 20 times faster, and less time-consuming. This research article reveals that the role of green cement as an additive material for 3D printing.

• Textile Coloration and Finishing
• /
• v.22 no.2
• /
• pp.94-100
• /
• 2010

Colored compounds adsorption from the textile dyeing effluents on activated carbons produced from various indigenous vegetable sources by zinc chloride activation is studied. The most important parameters in chemical activation were found to be the chemical ratio of $ZnCl_2$ to feed (3:1), carbonization temperature (460-470 $^{\circ}C$) and time of activation (75 min). The absorbance at 511 nm (red effluent) and 615 nm (blue effluent) are used for estimation of color. It is established that at optimum temperature ($50^{\circ}C$), time of contact (30-40 min) and adsorbent loading (2 g/L), activated carbons developed from rain tree (Samanea saman) saw dust and blackberry (Randia formosa) tree saw dust showed great capability to remove color materials from the effluents. It is observed that adsorption of reactive dyes by all types of activated carbons is more than that of disperse dyes. It is explained that because of its acidic nature the activated carbon can adsorb better reactive dye particles containing large number of nitrogen sites and $-SO_3Na$ group in their structure. The use of activated carbons from the indigenous biomass would be economical, because saw dusts are readily available waste worldwide.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.11 no.2
• /
• pp.31-35
• /
• 1982

Alcohol fermentation was carried out by using the yeast (S. cerevisiae) and soybean whey as the sole carbon source. The whey was gained form waste after manufacturing of soybean curd. The whey contained approximately one gram sugar per hundred mililter and the sugar was consisted of a 65 per cent of reducing sugar. However, it showed a low protein content of 43mg per the same volume. Ammonium sulfate showed the best effect on the generation of carbon dioxide among three kinds of tested nitrogen sourogen sources, potassium nitrate, urea and ammonium sulfate. Thus, fermentation was carried out with supplement of 2.0g ammonium sulfate to one liter of soybean whey. During fermentation continued for 48 hours, the maximum amount of ethanol 1.86g was produced from one liter of soybean whey. The ethanol fermentation utilized 81 and 94% of its initial sugar and protein contents, respectively.

• The Korean Journal of Food And Nutrition
• /
• v.11 no.5
• /
• pp.499-505
• /
• 1998

The purpose of this study was to ivestigate the structural characteristics of waste soulble browning reaction prodcuts (WS-BRPs) isolated from Korean red ginseng. They all showed the maximum absorbances at near 280 nm. Their IR spectra suggested the presence of hydroxyl, amide carbonyl and aliphatic methine groups. From sugar analysis it was identified that L and S-1 contained two kinds of suggar, glucose and xylose, and S-2, a fructose together with glucose and xylose. Thirteen different amino acids were identified in L. Ten amino acids from S-1 and seven amino acids from S-2 were identified using Auto Amino Acid Analyzer. Glycine, serine and glutamic acid in S-1 and one unknown amino acid and glycine in S-2 were detected as the major amino acids, respectively. From the 1H-and 13C-NMR spectra, it was identified that a number of sugar moieties, carbonyl and carbon double bonds (only in S-2) were contained in the three WS-BRP components. Approximate number of sugar moiety of L, S-1 and S-2 was determined to be 8∼10, 9∼11 and 4∼5, respectively. Contents of nitrogen, carbon and hydrogen showed L>S-1>S-2.