• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.535-540
• /
• 2022

DC-link capacitors are reliability-critical components in a photovoltaic (PV) inverter. Typically, the lifetime of a DC-link capacitor is evaluated by considering the voltage and hot-spot temperature of the capacitor under the specific operating condition of the PV inverter. However, the output of the PV inverter is determined by solar irradiation and ambient temperature, which vary with the seasons; accordingly, the hot-spot temperature of the capacitor also changes. Therefore, the mission profile of the PV system should be considered to effectively evaluate the reliability of the DC-link capacitor. In this study, the reliability of the DC-link capacitor of a three-level NPC inverter is comparatively analyzed with and without considering the mission profiles of the PV system, where two mission profiles recorded in Arizona and Iza are considered. The accumulated damage of the DC-link capacitor is calculated based on the lifetime model by analyzing its thermal loading. Afterward, a reliability evaluation of the DC-link capacitor is performed at the component level and then at the system level by considering all capacitors by means of Monte Carlo analysis. Results reveal the importance of performing a mission-profile-based reliability evaluation during the design of high-reliability PV inverters to achieve the target reliability performance.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.4
• /
• pp.116-120
• /
• 2009

Ceramic-polymer composites have been investigated for their suitability as embedded capacitor materials because they combine the processing ability of polymers with the desired dielectric properties of ceramics. This paper discusses the dielectric properties of the ceramic ($BaTiO_3$)-polymer (Epoxy) composition as a function of ceramic particle size at a ceramic loading of 40 vol%. The dielectric constant of these ceramic-polymer composites increases as the powder size decreases. Results show that ceramic-polymer composites have a high dielectric constant associated with the $BaTiO_3$ powder with a 200 nm particle size, high insulation resistance, high breakdown voltage (> 22 KV/mm), and low dielectric loss (0.018-0.024) at 1 MHz.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.59-60
• /
• 2017

In this paper, we studied a design method for obtaining broadband property by loading a chip capacitor on a coplanar waveguide(CPW)-fed compact quasi-Yagi antenna(QYA). The proposed antenna is a three-element QYA with dipole, reflector, and director. To reduce the size, the ends of both dipole and reflector are bent, and balun is incorporated in the antenna. To improve impedance matching, the loading position and capacitance value of chip capacitor were determined. From some simulations, the proposed antenna using an FR4 substrate with a size of 90 mm by 90 mm was designed for the operation in a broadband covering the UHF RFID and GPS systems. The antenna showed a good performance with a broadband of 850-1,626 MHz(62.7%) for a VSWR ${\leq}2$, a gain ${\geq}3dBi$, and a frong-to-back ratio ${\geq}4.6dB$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.826-834
• /
• 1994

The purpose of this study is to identify torque characteristics in capacitor type electric motors and to illustrate the effects of several design parameters on the fluctuating components of the motor torque. To do this, two revolving field theory and stationary reference frame theory were applied to derive governing equations for the torque generated by motor. For simulation studies, parameters of the motor components were measured under the conditions of no loading and locking. Based on these, effects of several design variables on the torque characteristics were analyzed and compared with the actual measurements, which were estimated indirectly by measuring the stator voltage and current. Then, some illustrative improvements in design are suggested by taking Taguchi method.

• Journal of Electrochemical Science and Technology
• /
• v.6 no.2
• /
• pp.59-64
• /
• 2015

Spherical Li₄Ti₅O₁₂ and Li₄Ti₅O₁₂ carbon nanotube (CNT) composites were synthesized using a colloid system. The electrochemical properties of the composites were thoroughly examined to determine their applicability as hybrid capacitor anodes. The electrical conductivity of the spherical Li₄Ti₅O₁₂-CNT composite was improved over that of the spherical Li₄Ti₅O₁₂ composite. The synthesized composites were utilized as the anode of a hybrid capacitor, which was assembled with an activated carbon (AC) positive electrode. The CNTs attached on the spherical Li₄Ti₅O₁₂ particles contributed to a 51% reduction of the equivalent series of resistance of the Li₄Ti₅O₁₂-CNTs/AC hybrid capacitor compared to the Li₄Ti₅O₁₂/AC hybrid capacitor. Moreover, the Li₄Ti₅O₁₂-CNTs/AC hybrid capacitor showed a larger capacitance than the Li₄Ti₅O₁₂/AC hybrid capacitor; specifically, the Li₄Ti₅O₁₂-CNT/AC hybrid capacitor showed 1.6 times greater capacitance at 40 cycles with a 10 mA cm⁻² loading current density.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.423-428
• /
• 2010

To reduce polarization of electrochemical capacitor based on carbon nanotube, titanium oxide nanoparticles were deposited by ultrasound. The pore distribution of $TiO_2$/CNT nanoparticle exhibited surface area of $341\;m^2g^{-1}$ when $TiO_2$ content was 4 wt %, which was better than that of pristine CNT with surface area of $188\;m^2g^{-1}$. The analyses indicated that titanium oxide (particle diameter < 20 nm) was deposited on the CNT surface. The electrochemical performance was evaluated by using cyclic voltammetry (CV), impedance measurement, and constant-current charge/discharge cycling techniques. The $TiO_2$/CNT composite electrode showed relatively better electrochemical behaviors than CNT electrode by increasing the specific capacitance from $22\;Fg^{-1}$ to $37\;Fg^{-1}$ in 1 M $H_2SO_4$ solution. A symmetric cell assembled with the composite electrodes showed the specific capacitance value of $11\;Fg^{-1}$ at a current loading of $0.5\;mAcm^{-2}$ during initial cycling.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.87-96
• /
• 2004

Polymer/ceramic composites are the most promising embedded capacitor material for organic substrates application. Predicting the effective dielectric constant of polymer/ceramic composites is very important for design of composite materials. In this paper, we measured the dielectric constant of epoxy/$BaTiO_3$ composite embedded capacitor films with various $BaTiO_3$ particles loading for 5 different sizes $BaTiO_3$ powders. Experimental data were fitted to several theoretical equations to find the equation useful for the prediction of the effective dielectric constant of polymer/ceramic composites and also to estimate the dielectric constant of $BaTiO_3$ powders. The Lichtenecker equation and the Jayasundere-Smith equation were useful for the prediction of the effective dielectric constant of epoxy/$BaTiO_3$ composites. And calculated dielectric constants of the $BaTiO_3$ powders were in the range of 100 to 600, which were lower than those of $BaTiO_3$ bulk ceramics.

• Korean Journal of Optics and Photonics
• /
• v.1 no.2
• /
• pp.169-177
• /
• 1990

We have constructed the laser system which was consisted of a high voltage pulse poner supply, a rapid high voltage spark gap and the Blumlein transmission line circuit of the multiple parallel plate capacitor type, and have studied the self-preionization effect from this laser system without additional modifications. The value of inductive or resistive loading of the laser oscillator seems to have a significant effect on the preionization. The optimal operational condition of this laser system was obtained at the inductive loading of L = I mtl across the laser tube with the spark gap distance of 6.0 mm. nitrogen pressure of 50 torr, when repetition rate was 70 Hz. Stability was found to be better than 2.0Yo and EIP was 867 V/cm.torr.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.4
• /
• pp.493-504
• /
• 2011

The present paper presents a genetic algorithm (GA) to maximize social welfare and perform congestion management by optimally placing and sizing one Thyristor-Controlled Series Capacitor (TCSC) device in a double-sided auction market. Simulation results, with line flow constraints before and after the compensation, are compared through the Sequential Quadratic Programming SQP method, and are used to analyze the effect of TCSC on the congestion levels of modified IEEE 14-bus and 30-bus test systems. Quadratic, smooth and nonsmooth (with sine components due to valve point loading effect) generator cost curves, and quadratic smooth consumer benefit functions are considered. The main aims of the present study are the inclusion of customer benefit in the social welfare maximization and congestion management objective function, the consideration of nonsmooth generator characteristics, and the optimal locating and sizing of the TCSC using real code-based GA to guarantee fast convergence to the best solution.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.5
• /
• pp.33-41
• /
• 2000

In this paper, a symmetric QMSA(Quarter-wavelength Microstrip Antenna) loading a capacitor to spread the electric flux lines is proposed. It was found that the bandwidth of this symmetric QMSA is broader than that of the asymmetric QMSA having a right-side Parallel plate only to load a capacitor. It was also found that this antenna could receive both vertically and horizontally polarized waves at 2.13GHz, and would be useful as a small antenna for wireless telephones and for indoor communication. A transmission line circuit model of this antenna was obtained and used to compute the resonant frequency and the return loss of the antenna accurately.