• 동굴
• /
• 제82호
• /
• pp.1-4
• /
• 2007

In this paper, the etching of Au films using photoresist masks on Si substrates was investigated using a capacitively coupled plasma etch reactor. The advantages of plasma etch techniques over current methods for Au metalization include the ability to simplify the metalization process flow with respect to resist lift-off schemes, and the ability to cleanly remove etched material without sidewall redeposition, as is seen in ion milling. The etch properties were measured for different gas mixing ratios of CF4/Ar, and chamber pressures while the other conditions were fixed. According to statistical design of experiment (DOE), etching process of Au films was characterized and also 20 samples were fabricated followed by measuring etch rate, selectivity and etch profile. There is a chemical reaction between CF4 and Au. Au- F is hard to remove from the surface because of its high melting point. The etching products can be sputtered by Ar ion bombardment.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.284-284
• /
• 2011

Recently, the increasing degree of device integration in the fabrication of Si semiconductor devices, etching processes of nano-scale materials and high aspect-ratio (HAR) structures become more important. Due to this reason, etch selectivity control during etching of HAR contact holes and trenches is very important. In this study, The etch selectivity and etch rate of TEOS oxide layer using ACL (amorphous carbon layer) mask are investigated various process parameters in CH2F2/C4F8/O2/Ar plasma during etching TEOS oxide layer using ArF/BARC/SiOx/ACL multilevel resist (MLR) structures. The deformation and etch characteristics of TEOS oxide layer using ACL hard mask was investigated in a dual-frequency superimposed capacitively coupled plasma (DFS-CCP) etcher by different fHF/ fLF combinations by varying the CH2F2/ C4F8 gas flow ratio plasmas. The etch characteristics were measured by on scanning electron microscopy (SEM) And X-ray photoelectron spectroscopy (XPS) analyses and Fourier transform infrared spectroscopy (FT-IR). A process window for very high selective etching of TEOS oxide using ACL mask could be determined by controlling the process parameters and in turn degree of polymerization. Mechanisms for high etch selectivity will discussed in detail.

• 대한전기학회논문지
• /
• 제43권5호
• /
• pp.802-808
• /
• 1994

The purpose of this paper is to describe an application of plasma polymerized thin film as an electron beam resist. Plasma polymerized thin film was prepared using an interelectrode capacitively coupled gas-flow-type reactor, and chosen methylmethacrylate(MMA)and methylmethacrylate-tetrameth-yltin(MMA-TMT) as a monomer. This thin films were also delineated by the electron-beam apparatus with an acceleration voltage of 30kV and an expose dose ranging from 20 to 900$\mu$C/cmS02T. The delineated pattern in the resist was developed with the same reactor which is used for polymerization using an argon as etching gas. The growth rate and etching rate of the thin film is increased with increasing of discharge power. Thin films by plasma polymerization show polymerization rate of 30~45($\pm$3) A/min, and etching rate of 440($\pm$30) A/min during Ar plasma etching at discharge power of 100W. In apparently lower than that of conventional PMMA, but the plasma-etching rate of PP(MMA-TMT) was higher than that of PPMMA.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.1066-1068
• /
• 1999

Magnetic field is commonly used in low temperature processing plasmas in order to obtain high density. E $\times$ B magnetron or surface multipole configuration were most popular. However, the properties of capacitively coupled rf plasma confined by axially applied static magnetic fields have rarely been studied. In this paper, the effects of magnetic field on the characteristics of 13.56MHz/40KHz argon plasma will be reported. Ion saturation current, electron temperature and plasma potential were measured by Langmuir probe and omissive probe. At low pressure region ($\sim$10mTorr), ion current was increased by a factor of 3 - 4 due to reduction of diffusion loss of charged particles to the wall. It was observed that magnetic field induces large time variation of the plasma potential. The experimental result was compared with particle-in-cell simulation. It was also observed that electron temperature tend to decrease with increasing magnetic induction level for 40KHz discharge.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2006년도 제30회 학술논문발표회 초록집
• /
• pp.119-119
• /
• 2006

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2005년도 제29회 학술발표회 초록집
• /
• pp.158-158
• /
• 2005

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2008년도 추계학술발표대회 및 제15회 신소재 심포지엄
• /
• pp.21.2-21.2
• /
• 2008

• 반도체디스플레이기술학회지
• /
• 제22권4호
• /
• pp.7-12
• /
• 2023

The edge ring placed on the outside of the electrostatic chuck (ESC) is a key component for protecting the ESC and controlling the etching uniformity of the edge of the wafer. Therefore, it is very important to understand the etching phenomenon of edge rings for edge ring management and equipment homeostasis. In this study, a specimen with SiO₂ hard mask and underlying Si mold was installed on the edge ring surface and the etching results were measured by varying the edge ring 2MHz RF power. By developing PI-VM model with high prediction accuracy and analyzing the roles of key parameters in the model, we were able to evaluate the effect of plasma and sheath characteristics around the edge ring on edge ring erosion. This analysis method provided information necessary for edge ring maintenance and operation.

• 한국표면공학회지
• /
• 제39권3호
• /
• pp.137-141
• /
• 2006

Process window for infinite etch selectivity of silicon nitride $(Si_3N_4)$ layers to ArF photoresist (PR) was investigated in dual frequency superimposed capacitive coupled plasma (DFS-CCP) by varying the process parameters such as low frequency power $(P_{LF})$, $CH_2F_2$ and $H_2$ flow rate in $CH_2F_2/H_2/Ar$ plasma. It was found that infinite etch selectivities of $Si_3N_4$ layers to the ArF PR on both blanket and patterned wafers can be obtained for certain gas flow conditions. The etch selectivity was increased to the infinite values as the $CH_2F_2$ flow rate increases, while it was decreased from the infinite etch selectivity as the $H_2$ flow rate increased. The preferential chemical reaction of the hydrogen with the carbon in the polymer film and the nitrogen on the $Si_3N_4$ surface leading to the formation of HCN etch by-products results in a thinner steady-state polymer and, in turn, to continuous $Si_3N_4$ etching, due to enhanced $SiF_4$ formation, while the polymer was deposited on the ArF photoresist surface.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2007년도 제32회 학술대회 초록집
• /
• pp.88-88
• /
• 2007