• Journal of Advanced Marine Engineering and Technology
• /
• 제23권6호
• /
• pp.778-784
• /
• 1999

In this study both the experimental and the analytic approach to find load characteristics on the cam-valve mechanism for matrine diesel engine were demonstrated. The experiment was per-formed with a test rig consisted of real engine components for cam-valve mechanism of overhead valve type. The 9-degree of freedom lumped mass model was developed to simulate cam-valve motion throughly. Behavior of the load acting on the cam-valve mechanism was estimated for the various cam speed. The load variation was getting deeper with the higher cam speed and the jumping of the follower was shown both in the experiment and in the simulation.

• 한국자동차공학회논문집
• /
• 제17권5호
• /
• pp.7-15
• /
• 2009

This paper introduces a new variable valve actuation mechanism with movable second cam center. Valve lift and open duration can be continuously varied according to engine speed and load conditions. A new method to analyze the kinematic relations between the first and second cam profiles and valve motion are also introduced. Because of rocker motion of the second cam, conventional motion conversion program could not be used in this problem. An example shows continuous variations of valve motion and adequate ramp incorporation throughout all valve lift modes. Valve acceleration profile at the high lift mode is similar to that of conventional valvetrains. Contact geometry analysis of the mechanism gives basic information on the load conditions between the components.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.505-506
• /
• 2007

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.121-128
• /
• 1999

In this study, a numerical procedure to analyze 3-dimensional unsteady elastohydrodynamic lubrication was developed. The procedure was applied to the actual cam and roller follower of the valve mechanism for a marine diesel engine. The pressure distribution between the cam and roller follower was calculated for the several cam rotating angles. The pressure spike is shown near the roller edge and it is getting higher as the external load is increased. The roller profile for reducing the pressure spike was suggested by the Hertzian contact analysis.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.269-270
• /
• 2006

• Tribology and Lubricants
• /
• 제16권3호
• /
• pp.201-207
• /
• 2000

The numerical procedure to analyze a non-steady 3-dimensional elastohydrodynamic lubrication on the cyclically loaded contact has been newly developed. The procedure was applied on the cam-roller contact of the valve mechanism for the marine diesel engine. Both the pressure distribution and the film thickness between the cam and roller follower were calculated for each time step of the whole cycle. The pressure spike is shown at the outlet of the roller edge and it is getting higher as the external load is increased. The film thicknesses in the result of the non-steady analysis have a tendency to increase compared to those in the result of the analysis with the assumption of steady state. Therefore, the surface roughness of the non-steady contact need not be limited below that of the steady contact of the equivalent operating conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.513-516
• /
• 2000

This paper presents the analytical studies on the stress and strain of driven valve system of internal combustion engines. The stress and strain is predict using FEM. The particular interest is the dynamic strain at a specific point of the valve and valve seat. Cam and follower Assuming that one rigid surface. This study forced the effects changing Young's modulus and density of valve and valve seat contact area. It supports that the indirect method using FEM is reliable for prediction the actual displacement, stress and strain in the valve system.

• Journal of Mechanical Science and Technology
• /
• 제20권3호
• /
• pp.345-357
• /
• 2006

By employing the concept of equivalent linkage, this paper presents an analytical method for analyzing the mechanical errors of disk cam mechanisms with a flat-faced follower. The resulting error equations do not really involve the location of the curvature center of the cam profile, and locating the curvature center of the cam profile is not essential. The resulting errors are significantly affected by the pressure angle, and the smaller pressure angle will result in the smaller mechanical error. In the worst case, owing to the joined effects of various design parameters, the accuracy of the follower motion may degrade considerably. For the oscillating follower case, all acceleration error functions have a sudden change at every beginning and at every end of the motion even though the theoretical follower displacement is cycloidal motion.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.147-154
• /
• 2000

A numerical procedure to analyze 3-dimensional elastohydrodynamic lubrication was applied on the cam-roller contact of the valve mechanism for a marine diesel engine. Both the pressure distribution and the film thickness between the cam and roller follower were calculated for each time step of the whole cycle. The pressure spike is shown at the outlet of the roller edge and it is getting higher as the external load is increased. An effective profiling method for the roller edge was suggested using the results of elastohydrodynamic lubrication analysis and the peak pressure was removed completely with the new profiling.

• 문화기술의 융합
• /
• 제8권5호
• /
• pp.591-596
• /
• 2022

다양한 산업분야에서 사용되는 4절 링크기구는 링크 길이가 고정되어 있으므로 기구의 움직임을 변경하기 위해서는 독립적인 링크기구나 제어장치를 추가해야 하는 불편함이 있다. 따라서 본 논문에서는 상황에 따라 링크기구의 운동을 선택적으로 제어할 수 있도록 링크 길이가 조절되는 가변형 4절 링크기구를 설계하였으며 링크기구에 의해 구동되는 제품인 선풍기에 적용하여 그 타당성을 검증하였다. 바람 범위의 효율성을 고려하여 선풍기 회전각도를3단계로 분할하였으며 각 구간에 필요한 링크 길이를 계산하였다. 또한, 원통캠을 이용하여 링크 길이를 조절하였으며 선풍기의 회전각도 조절 작동 여부를 실제 제작 및 측정을 통해 확인하였다. 본 논문에서 제시한 가변형 링크기구는 산업용 로봇이나 연료 밸브 시스템 등과 같은 4절링크 적용 제품의 효율성을 향상시킬 수 있을 것으로 기대된다.