• Membrane and Water Treatment
• /
• v.10 no.4
• /
• pp.259-264
• /
• 2019

Cost effective clay adsorptive microfiltration membranes were synthesized to remove Cr (III) from high polluted water. Raw and calcined bentonite were mixed in order to decrease the shrinkage and also increase the porosity; then, 20 wt% of carbonate was added and the samples, named B (without carbonate) and B-Ca20 (with 20 wt% calcium carbonate) were uniaxially pressed and after sufficient drying, fired at $1100^{\circ}C$ for 3 hours. Then, physical and mechanical properties of the samples, their phase analyses and microstructure and also their ability for Cr(III) removal from high polluted water (including 1000 ppm Cr (III) ions) were studied. Results showed that the addition of calcium carbonate lead the porosity to increase to 33.5% while contrary to organic pore formers like starch, due to the formation of wollastonite, the mechanical strength not only didn't collapse but also improved to 36.77 MPa. Besides, sample B-Ca20, due to the presence of wollastonite and anorthite, could remove 99.97% of Cr (III) ions. Hence, a very economic and cost effective combination of membrane filtration and adsorption technology was achieved for water treatment which made microfiltration membranes act even better than nanofiltration ones without using any adsorptive nano particles.

• Current Research on Agriculture and Life Sciences
• /
• v.3
• /
• pp.14-20
• /
• 1985

This study was carried out to evaluate the effects of whole layer placement of total of N.P.K. application with clay mineral such as Bentonits and Zeolite on the growth and the yield of rice in different sandy soils. The results obtained were as follows ; The yield was increased by whole layer placement of total amount of N.P.K. application with clay minerals in both soils examined compared with the treatment of N.P.K. only. In fine sandy loam soil, it was increased significantly at 5% level at N.P.K. + Zeolite 1.0 M/T and in fine sandy soil, at 5 % and 1 % at N.P.K. + Bentonits 0.5 M/T and N.P.K. + Bentonite 1.0 M/T, respectively. The nitrogen and silica content of rice straw at heading stage were increased and were tended to increase in phosphate and exchangeable cations such as potassium. calcium and magnesium by whole layer placement of total amount of N.P.K. application with clay mineral. The chemical properties of both soils were changed slightly after the harvest of rice by the whole layer placement of total amount of N.P.K. application with clay mineral ; pH, C.E.C., exchangeable base and available silica content were increased.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.32-33
• /
• 2016

In this work, pozzolanic activities of various waste materials were compared with those of well-known pozzolanic materials. Uncondensed and densified silica fume, two ASTM class F fly ashes with different calcium contents, and bentonite powder, ceramic powder obtained from wash basin, and waste glass wool, which can possibly possess pozzolanic property were chosen for comparison. Drop in electrical conductivity at 40℃ saturated lime solution was measured for each materials. The amount of Ca(OH)₂ decomposed from cement paste at 450~500℃ was also measured used to evaluate pozzolanic activity. The 28 day compressive strength were used to observe the mechanical property enhanced by various waste materials.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.7
• /
• pp.141-158
• /
• 2004

The dependency of criteria used to terminate compatibility tests on the prehydration and quality of bentonite in geosynthetic clay liners (GCLs) is evaluated based on permeation with chemical solutions containing 5, 10, 20, 50, and 100 mM calcium chloride ($CaCl_2$). The hydraulic conductivity tests are not terminated before chemical equilibrium between the effluent and the influent chemistry has been established, resulting in test durations ranging from < 1 day to > 900 days, with longer test durations associated with lower $CaCl_2$ concentrations. The evaluation includes both physical termination criteria (i.e., volumetric flow ratio and steady hydraulic conductivity based on ASTM D 5084, ${\ge}2$ pore volumes of flow, constant thickness of specimen) and chemical termination criteria requiring equilibrium between influent and effluent chemistry (viz., electrical conductivity, pH, and $Ca^{2+}\;and\;Cl^-$ concentrations). For specimens permeated with 5, 10, and 20 mM $CaCl_2$ solutions, only the criterion based on chemical equilibrium in $Ca^{2+}$ concentration correlates well with equilibrium in hydraulic conductivity, regardless of prehydration or quality of bentonite. However, all of the termination criteria, except for the volumetric flow ratio and 2 pore volumes of flow for the prehydrated specimens, correlate well with equilibrium in hydraulic conductivity regardless of prehydration or quality of bentonite when permeated with 50 and 100 mM $CaCl_2$ solutions. The results illustrate the uniqueness of the termination criterion based on solute concentration equilibrium between the effluent and the influent with respect to both prehydration and quality of bentonite in the GCLs.

• Journal of Bio-Environment Control
• /
• v.13 no.1
• /
• pp.8-15
• /
• 2004

Seedling mechanization of lettuce is known to be difficult due to the small seed size and the irregular seed shape. The purpose of seed pelleting is to make seedling mechanization possible by enlarging the seed size. After that, it can reduce seedling and thinning labours and can also save seeds. According to the results, there were significant differences on the percent germination and day to 50% final germination in accordance with the pelleting polymer. Among the pelleting polymer, gemination of seeds using polynimyl alcohol (PVA) was generally smooth, and followed by polyvinyl pyrrolidone (PVP), hydroxyethyl cellulose (HEC), methyl cellulose (MC), and wteen 80. The germination rate was also different according to the pelleting particulate matters. Generally, percent germination and speed of seed using the mixture of diatomaceous earth, talc and calcium carbonate were higher and faster than using other polleting materials, respectively. Thus, it should be suitable pelleting particulate matter for the pelleting of lettuce seeds. On the other hands germination of seeds using limestone, calcium oxide and benonite were low. The seed size of lettuce after pelleting was 33 times as large as the raw seed size. During the process of seed pelleting, netrient addition induced the decrement on the germination and the delay of germination speed. Also, there was differences in the germinability of pelleted seeds in accordance with the addition of nutrient sources. MS medium was generally lower than monosodium phosphate in inhibition of seed germination. Germination of pelleted seeds after priming was higher than the seeds without the treatment, and also showed the trend of early germination.

• Korean Journal of Environment and Ecology
• /
• v.20 no.4
• /
• pp.436-447
• /
• 2006

Recently, there is increasing demand on enhancing the efficiency of hydro-seed spraying in afforestation for damaged or degraded land including forest road slopes. In this study, we focus on how seed coating and molding may affect seed germination and seedling growth. Plant species used in the study are Lespedeza cyrtobotrya, Indigofera pseudotinctoria, Arudineila hirta, Poa pratensis, and Lolium perenne. The results of seed germination and seedling growth with and without seed coating and molding are analyzed as follows: 1. For all the species and in both seeding with molding covered with soil and seeding without molding in which seeds were over sown, the increment of germination ratio by seed coating method is greater than by non·coating one. Seed coating increases average germination ratios observed in seeding with molding and without molding by 11.2% and 21.4%, respectively. Germination force may decrease from 0.8 to 3.7 days depending on the plant species and the treatments. The $LD_{50}$ decreased by $0.8{\sim}2.6$ days. However, seed coating delays the start of germination by approximate 1 day for all of the observed plants. 2. Seed coating may have the effect of accelerating the growth of stem and leaf and root. The experimental result shows that seed coating leads to 21.7% and 34.8% increment of average stem and leaf growth by seeding with molding and without molding, respectively. In terms of root growth, seeding with molding results in 22.0% increment while seeding without molding produces 26.2% increased root growth. 3: Compared to seeding without molding, germination starts on an average of 1.3 days later in seeding coated seeds with molding. However. the germination ratio is increased by 5%, and germination force and $LD_{50}$ are observed to shorten by 1.0 day and 1.4 days, respectively. Meanwhile, whether seeds are coated or not may be more related with germination and seedling growth in seeding without molding than with those in seeding with molding. 4. In this study, coating materials are examined to look at which ones are better in each treatment. Coating with Vermiculite+Talcum is the most effective in germination and seedling growth for overall plants. Seed coating using Bentonite, Calcium Carbonate, and Calcium Hydroxide shows better results than non-coating does. 5. When seeds are coated, the greatest enhancement of seed germinations was observed in Indigofera pseudotinctoria and, in the case of seedling growth, Lespedeza cyrtobotrya has the most increasing observation value among the 5 examined species. These results may indicate that woody plant seeds, having greater sizes of seeds than ones of grass seeds, may have greater relation with seed coating than grass plant seeds may have. 6. Therefore, if seeds cannot be molded up after hydro-seeding on forest road slopes, it is recommended that seeds for restoration be pre-coated with Vermiculite+Talcum and then be sowed, in order to quickly stabilize the damaged slope and achieve successful afforestation.

• 한국생물공학회:학술대회논문집
• /
• 2003.04a
• /
• pp.719-723
• /
• 2003

The dispersing activity and physical properties of exopolysaccharide (Cystan) produced by Cystobacter sp. MSL-9 was studied. Dispersing activity of Cystan was measured by using bentonite, calcium carbonate, and kaolin. Rheological properties of Cystan were investigated by using a rheometer MCR300. It was found that dispersing activity of Cystan was maintained under various pH and temperature conditions. A particle size analyzer BI-9000AT was used for the particle size measurement of Cystan in aqueous solution. The high dispersing activity and stability under various pH and temperature conditions showed the feasibility of Cystan as a industrial biodispersant.

• Economic and Environmental Geology
• /
• v.29 no.1
• /
• pp.57-63
• /
• 1996

The Dalsung copper-tungsten mine in the Taegu area, Korea was closed in 1975 and may be the sources of the heavy metal contamination in the tributary system and soil-plant system due to the mine drainage derived from the mine wastes and tailings. To examine the degree and extent of heavy metal contamination in the vicinity of Dalsung mine area, stream water and soil samples were taken and analyzed for heavy metals by ICP-AES and AAS. Highly contaminated soils are found near the Lower Tunnel No.0 ranging up to $1760{\mu}g/g$ As, $2060{\mu}g/g$ Cu, $1120{\mu}g/g$ Pb and 346 ${\mu}g/g$ Zn. From the results of the sequential extraction methods for the metal speciation, the heavy metals in soils may be derived from soil parent materials and acid mine drainage. With the processes for the heavy metal removal, most of the heavy metal ions in the acid mine drainage are removed by being exchanged with Ca ions held by the bentonite, hydroxyapatite and calcium hydoxide.

• Economic and Environmental Geology
• /
• v.16 no.3
• /
• pp.149-161
• /
• 1983

Fuller's earth deposits from Miocene sedimentary sequences in Gyeong Sang-do contain up to 95% Ca-montmorillonite accompanied by cristobalite, clinoptilolite, mordenite, quartz, feldspar and X-ray amorphous material. Differential thermal analysis, infrared and electron microscopic data are given for the montmorillonite component. The ease with which the exchangeable calcium of the montmorillonite could be replaced by sodium (to give a product with properties similar to that of a bentonite) was monitored by the Atterberg liquid limit test. Some samples tested as possible binders for foundry moulding sands gave results that compared favourably with material currently being used for this application. Many of the samples also met the OCMA specifications for clays used in drilling muds.

• Journal of Korean Society of Water and Wastewater
• /
• v.14 no.4
• /
• pp.318-327
• /
• 2000

Sludge production from water treatment plants is increasing each year because water resources deterioration is proceeding and water supply facilities are growing due to water demand increase. Water treatment plant sludges can be modified to soil cover in sanitary landfilling site through the lime treatment and other alternatives. The compression strength of $1.0kg/cm^2$ is necessary for the dozer operation on soft son cover material at municipal landfilling site. Modified sludge was experimentally produced in this study with lime, bentonite, loess, and activated loess dosing. X-ray diffraction patterns of the limed water treatment plant sludge confirmed the presence of calcium carbonate and ettringite. Unconfined compression strength properties of modified sludges showed material property improvement applicable for soil cover alternatives. When adding 20-30% activated loess to water treatment plant sludges. the modified sludges could reach the compression strength for cover soil after 7 days solidification reaction, but decrease of compression strength was intentioned in 28 days reaction period. Solidification effect of the modified sludge with activated loess was observed through the scanning electron microscope.