• Journal of Korea Foundry Society
• /
• v.20 no.4
• /
• pp.254-259
• /
• 2000

Metal matrix composites(MMCs) reinforced with hard particles have many potential application in aerospace structures, auto parts, semiconductor package, heat resistant panels, wear resistant materials and so on. In this work, the effect of SiC partioel sizes(50 and 100 ${\mu}m$) and additional elements such as Si, Cu and Ti on the microstructure and the wear property of $Al-5Mg-X(Si,Cu,Ti)/SiC_p$ composites produced by pressureless infiltration method have been investigated using optical microscopy, scanning eletron microcopy(SEM) with EDS(energy dispersive spectrometry), hardness test, X-ray diffractometer(XRD) and wear test. In present study, the sound $Al-5Mg-X(Si,Cu,Ti)/SiC_p$(50 and 100 ${\mu}m$) composites were fabricated by pressureless infiltration method. The $Al-5Mg-0.3Si-O.1Cu-O.1Ti/SiC_p$ composite with $50 {\mu}m$ size of SiC particle has higher hardness and better wear property than any other composite with $100{\mu}m$ size of SiC particle produced by pressureless infiltration method. The hardness and wear property of $Al-5Mg/SiC_p$(50 and 100 ${\mu}m$) composites were enhanced by the addition of Si, Cu and Ti in Al-5%Mg matrix alloy.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.2
• /
• pp.73-76
• /
• 2004

0-3 PbTiO$_3$/P(VDF/TrFE) nanocomposite thin films for passive pyroelectric infrared sensors were fabricated by a two-step spin coating technique. 65wt% VDF and 35 wt% TrFE was formed into a P(VDF/TrFE) powder. Nano size PbTiO$_3$ powder was used. 0-3 connectivity of PbTiO$_3$/P(VDF/TrFE) composite film was successfully achieved and observed using SEM photography. The dielectric constant and pyroelectric coefficient were measured and compared with P(VDF/TrFE). A very low dielectric constant (13.48 at 1KHz and sufficiently high pyroelectric coefficient (3.101 nC/$\textrm{cm}^2$ㆍk at 5$0^{\circ}C$) were measured. This nanocomposite can be used for a new pyroelectric infrared sensor to achieve better performance.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.918-924
• /
• 1998

This study has been carried out to investigate the effect of reaction milling time on the synthesis of Ti- TiC p powder synthesised from the elemental titanium and activated carbon by reaction milling(RM), and the effect of vacu­u urn hot pressing temperature and TiC volume fraction on microstructural and mechanical properties of Ti- TiC com­p posite $\infty$ns이idated by vacuum hot pressing(VHP).T The elemental powders of titanium and activated carbon can be converted into Ti- TiC composite powders by reac­t tion milling for about 300hours, and were the average grain size of the as- milled powders has been measured to be a about $5\mu\textrm{m}$. The relative density of Ti- TiC VHPed above $1000^{\circ}C$ during Ihr is about 98% and the mechanical properties o of In- situ Ti- TiC composites are improved by TiC particle dispersed uniformly on titanium matrix. In order to investi­g gate thermal stability of Ti- TiC composite, after annealing at $600^{\circ}C$ for 80hrs micro- Vickers hardness have been per­f formed, and the values have been shown little changed as compared with those before annealing. The compact has b been tested on high temperature compressive test at $700^{\circ}C$ and has showed a high temperature compressive strength of 330MPa in a Ti- 20vol% TiC.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.11 no.1
• /
• pp.13-20
• /
• 1985

The decreased preservative effect by tale and $TiO_2$ for emulsions obtained with polyoxyethylene surfactant was studied by various analytical methods and biological test. The preservative effect of methyl p-hydroxybenzoate was decreased by the addition of talc and $TiO_2$ and this result was attributed to the adsorption of methyl p-hydroxybenzoate on them. Talc exhibited more decreased preservative effect than that of $TiO_2$. The amount of the adsorption of methyl p-phydroxybenzoate by talc at $20^{\circ}C$ could be represented by the following equation; $a=11.511C^{0.747}$.

• Korean Journal of Materials Research
• /
• v.15 no.5
• /
• pp.318-322
• /
• 2005

Ti-capped NiSi contacts were formed on $p^+/n$ junctions to improve the leakage problem and then Cu was deposited without removing the Ti-capping layer in an attempt to utilize as a diffusion barrier. The electrical characteristics of these $p^+/n$ diodes with Cu/Ti/NiSi electrodes were measured as a function of drive-in RTA(rapid-thermal annealing) and silicidation temperature and time. When drive-in annealed at $900^{\circ}C$, 10 sec. and silicided at $500^{\circ}C$, 100 sec., the diodes showed the most excellent I-V characteristics. Especially, the leakage current was $10^{-10}A$, much lower than reported data for diodes with NiSi contacts. However, when the $p^+/n$ diodes with Cu/Ti/NiSi contacts were furnace-annealed at $400^{\circ}C$ for 40 min., the leakage current increased by 4 orders. The FESEM and AES analysis revealed that the Ti-capping layer effectively prohibited the Cu diffusion, but was ineffective against the NiSi dissociation and consequent Ni diffusion.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.746-755
• /
• 2017

In this study, $CeO_2/TiO_2$ nanoparticle with structure of core and shell was synthesized by growing $TiO_2$ onto the surface of $CeO_2$ according to hydrolysis of $Ti(SO_4)_2$. Reaction time, temperature, concentration of $CeO_2$ slurry, pH control of $Ti(SO_4)_2$ were optimized about synthesis of $CeO_2/TiO_2$ core-shell nanoparticle. It was found that optimal mole ratio range of $CeO_2:TiO_2$ was 1:0.2~1.1, the optimal concentration of $CeO_2$ slurry was 1 %, and the optimal reaction temperature was $50^{\circ}C$. The optimal concentration of $CeO_2$ slurry could be increased up to 10 % by adjusting the pH of $Ti(SO_4)_2$ to 1 using $NH_4OH$ and adding to $CeO_2$ slurry. If reaction was carried at $80^{\circ}C$ or higher, the separated $TiO_2$ particles were obtained instead of $CeO_2/TiO_2$ core-shell nanoparticles. The optimal reaction temperature was $50^{\circ}C$ at which good shaped core-shell structure of $CeO_2/TiO_2$ was obtained.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.54-54
• /
• 2011

The demand for low-friction, wear and corrosion resistant components, which operate under severe conditions, has directed attentions to advanced surface engineering technologies. The Filtered Vacuum Arc Cathode Deposition (FVACD) process has demonstrated atomically smooth surface at relatively high deposition rates over large surface areas. Preparation of Ti-Si-C-N nanocomposite coatings on (100) Si and stainless steel substrates with tetramethylsilane (TMS) gas pressures to optimize the film preparation conditions. Ti-S-C-N coatings were characterized using X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, nanoindentation, Rockwell C indentation and ball-on-disk wear tests. The XRD results have confirmed phase formation information of TiSiCN coatings, which shows mixing of TiN and TiC structure, corresponding to (111), (200) and (220) planes of TiCN. The chemical composition of the film was investigated by XPS core level spectra. The binding energy of the elements present in the films was estimated using XPS measurements and it shows present of elemental information corresponding to Ti2p, N1s, Si 2p and C1. Film hardness and elastic modulus were measured with a nano-indenter, and film hardness reached 40 GPa. Tribological behaviors of the films were evaluated using a ball-on-disk tribometer, and the films demonstrated properties of low-friction and good wear resistance.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.1
• /
• pp.76-88
• /
• 2004

The catalytic oxidation reaction of several cycloolefins in $CH_2Cl_2$ have been investigated using non-redox metalloporphyrin(M = Ga(III), In(III) and TI(III) complexes as a catalyst and sodium hypochlorite as a terminal oxidant. Porphyrins were $(p-CH_3O)$TPP, $(p-CH_3)$TPP, TPP, (p-F)TPP, (p-Cl)TPP and $(F_{20})$TPP (TPP=5,10,15,20-tetraphenyl-21H,23H-porphyrin) and olefins were cyclopentene, cyclohexene, cycloheptene and cyclooctene, The substrate conversion yield(%) was investigated according to the radius effect of non-redox metal ion, substituent effect and hindrance effect of metalloporphyrin. The conversion yield of cycloolefin was in the following order : $C_5$ < $C_6$ < $C_7$ = $C_8$.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.157-169
• /
• 2009

The aim of this study was to evaluate effect of implant abutment screw coating treatment on joint stability, investigating mechanical properties of these. For this study used $ExFeel^{(R)}$ external hexed implant system and $15mm{\times}1mm$ discs. Experimental group was $1{\mu}m$ TiN, TiCN, TiC coated abutment screws and discs. To know mechanical property, i evaluated adhesion strength, surface hardness, using disc, corrosion test using screw. The results were as follows : rotation angle of coated screws increased than that of non-coated screw because of lower friction coefficient, especially TiC coated screw group had the largest value, but removal torque decreased in all coated screws (p<0.05). Torque loss before and after fatigue test was the smallest in TiC-coated screws, and the largest in non-coated screws (p<0.05), and there was no statistically significant difference between dry condition and wet condition of screws because of higher surface hardness and lower friction coefficient. From the above results, TiN, TiCN, TiC coating group had high abrasion resistance, especially TiC coated group which had low torque-consuming, high rotation angle as low friction coefficient will be considered to influence on implant abutment screw joint stability positively.

• Laser Solutions
• /
• v.10 no.4
• /
• pp.13-17
• /
• 2007

Electron beam weldability was investigated for 1mm thick cold rolled sheets of commercially pure grade titanium and Ti-6Al-4V alloy. Accelerating voltage of 40kV, beam current of 6mA, and weld speed of 0.8m/min was used and focal position of focused electron beam was just on the surface of workpiece. Microstructure of weld metal, the heat affected zone and base metal was observed using optical microscope. Vickers hardness was measured across the welds and the transverse tensile test was carried out. Hydroformability test was also carried out for the butt welded coupons of commercially pure grade titanium. For the electron beam welded C P Ti, the average grain size was equiaxed $\alpha(15{\sim}25{\mu}m)$ for base metal, coarse equiaxed $\alpha(80{\sim}200{\mu}m)$ for weld metal and annealed and enlarged grain($40{\sim}120{\mu}m$) for the HAZ. The vickers hardness of C P Ti was $180{\sim}200Hv$ for base metal, and $160{\sim}180Hv$ for the weld metal and the HAZ. For the electron beam welded Ti-6Al-4V alloy, the vickers hardness was 360Hv for the base metal, abd $400{\sim}425Hv$ for the weld metal and the HAZ. All the failure occurred at the base metal, when the transverse weld tensile test was carried out for both electron beam welded C P Ti and Ti-6Al-4V alloy. The formability of electron beam welded C P Ti was decreased compared with that of C P Ti base alloy.