• Journal of Magnetics
• /
• 제14권1호
• /
• pp.18-22
• /
• 2009

The shape anisotropy effect of a giant magnetoresistance-spin valves (GMR-SV) device with a glass/NiO/NiFe/CoFe/Cu/CoFe/NiFe layered structure for use in the detection of magnetic property of molecules within a cell was investigated. The patterned device was given uniaxial anisotropy during the sputtering deposition and vacuum post-annealing, which was performed at $200^{\circ}C$ under a 300 Oe magnetic field. The pattern size of the device, which was prepared through the photolithography process, was $2{\times}15\;{\mu}m^2$. The experimental results confirmed that the best design for a GMR-SV device to be used as a biosensor is to have both the axis sensing current and the easy axis of the pinned NiO/NiFe/CoFe triple layer oriented in the direction of the device's width, while the easy axis of the free CoFe/NiFe bilayer should be pointed along the long axis of the device.

• 한국결정성장학회지
• /
• 제14권5호
• /
• pp.187-192
• /
• 2004

We try to use isopropanol which has low boiling point to prepare ZnO thin films at low temperature. ZnO thin films were prepared by sol-gel spin-coating method using zinc acetate dehydrate-isopropanol-monoethanolamine (MEA) solution. The c-axis preferred orientation and optical properties of ZnO films with preheating temperature have been investigated. ZnO thin films were preheated at 200 to $300^{\circ}C$ with an interval of $25^{\circ}C$ and post-heated at $650^{\circ}C$. The ZnO film preheated at $275^{\circ}C$ and post-heated at $650^{\circ}C$ was highly oriented along c-axis (002) plane, and the surface with homogeneous and dense microstructures was formed having nano-sized grains. The optical transmittance was above 90 % in the visible range and exhibited absorption edges at 368 nm wavelength.

• 한국전기전자재료학회논문지
• /
• 제21권5호
• /
• pp.463-467
• /
• 2008

Aluminum nitride (AlN) thin films have been deposited on Au electrodes by using reactive RF magnetron sputtering method in a gas mixture of Ar and $N_2$ at different substrate temperature. It was found that substrate temperature was varied in the range up to $400^{\circ}C$, highly c-axis oriented film can be obtained at $300^{\circ}C$ with full width at half maximum (FWHM) $3.1^{\circ}$. Increase in surface roughness from 3.8 nm to 5.9 nm found to be associated with increase in grain size, with substrate temperature; however, the AlN film fabricated at $400^{\circ}C$ exhibited a granular type of structure with non-uniform grains. The Al 2p and N 1s peak in the X-ray photoelectron spectroscopy (XPS) spectrum confirmed the formation of Al-N bonds. The XPS spectrum also indicated the presence of oxynitrides and oxides, resulting from the presence of residual oxygen in the vacuum chamber. It is concluded that the AlN film deposited at substrate temperature of $300^{\circ}C$ exhibited the most desirable properties for the application of high-frequency surface acoustic devices.

• 한국안광학회지
• /
• 제10권3호
• /
• pp.193-203
• /
• 2005

Zn-나프텐산염을 출발 원료로 사용하고 스핀코팅 - 열분해법을 이용하여 실리카 유리 위에 c축으로 배향된 나노 결정질 ZnO 박막을 제조하였다. X-선 회절 분석을 행한 결과, 모든 시편에서 ZnO (002) 피크만이 관찰되었으며, 박막의 열처리 온도가 증가함에 따라 (002) 피크 강도가 증가하였다. 박막의 표면 미세 구조는 매우 균질하였으며, 입자들 간의 응집은 관찰되지 않았다. 박막의 topology를 주사형 탐침 현미경으로 분석한 결과에 따르면, 실리카 기판 자체의 불균질한 표면 특성과 ZnO 입자의 c축 배향 특성에 의한 것으로 보이는 3차원적인 입자성장이 모든 열처리 온도 영역에 대해 박막의 표면에서 관찰되었다. 고배향된 박막들 중에서 $800^{\circ}C$로 열처리한 박막의 표면이 가장 균질한 특성을 나타내었다. 박막의 가시영역에서의 투과율은 $1000^{\circ}C$로 열처리한 박막을 제외하고 모든 박막에 있어서 80% 이상의 투과율을 나타냈으며, 380~400nm 영역에서 날카로운 absorption edge가 나타났다. 흡수피크를 이용하여 계산된 오든 박막의 에너지 밴드 캡은 ZnO 단결정 및 다른 연구자들에 의해 보고된 박막과 같은 영역에 존재하였다. 본 연구에서 제조된 ZnO 박막들 중에 치밀한 입자 성장과 균질한 표면 특성을 보이는 $600^{\circ}C{\sim}800^{\circ}C$로 열처리된 박막은 UV차단성 투명전도막 및 렌즈 등의 광학소자에 실질적인 응용이 기대 된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.305-309
• /
• 2002

We have successfully fabricated a Metal-Ferroelectric-Insulator-Semiconductor (MFIS) structure using Bi$\sub$4-x/La$\sub$x/Ti$_3$O$\sub$12/ (BLT) ferroelectric thin film and SiO$_2$/Nitride/SiO$_2$ (ONO) stacked buffer layers for single transistor type ferroelectric nonvolatile memory applications. BLT films were deposited on 15 nm-thick ONO buffer layer by sol-gel spin-coating. The dielectric constant and the leakage current density of prepared ONO film were measured to be 5.6 and 1.0 x 10$\^$-8/ A/$\textrm{cm}^2$ at 2MV/cm, respectively, It was interesting to note that the crystallographic orientations of BLT thin films were strongly effected by pre-bake temperatures. X-ray diffraction patterns showed that (117) crystallites were mainly detected in the BLT film if pre-baked below 400$^{\circ}C$. Whereas, for the films pre-baked above 500$^{\circ}C$, the crystallites with preferred c-axis orientation were mainly detected. From the C-V measurement of the MFIS capacitor with c-axis oriented BLT films, the memory window of 0.6 V was obtained at a voltage sweep of ${\pm}$8 V, which evidently reflects the ferroelectric memory effect of a BLT/ONO/Si structure.

• 센서학회지
• /
• 제5권3호
• /
• pp.87-92
• /
• 1996

Pb과잉인 PLT 타겟을 이용하여 MgO(100) 단결정 기판위에 고주파 마그네트론 스펏터링법으로 PLT박막을 제조하였으며, c-축 배향에 따른 물리적 및 전기적 특성을 조사하였다. PLT박막의 c-축 배향성은 제조조건에 따라 변화하며, 본 연구에서의 제조조건은 기판온도가 $640^{\circ}C$, 분위기압이 10 mTorr, $Ar/O_{2}$비가 10 및 고주파 전력밀도가 $1.7 W/cm^{2}$이었다. 이러한 조건에서 제조된 PLT 박막은 표면에서의 Pb/Ti 비가 1/2, 저항률이 $8{\times}10^{11}{\Omega}{\cdot}cm$ 및 비유전률이 110 이었다. PLT박막을 이용하여 초전형 적외선 센서를 제조하였으며, 제조된 적외선 센서의 피크 대 피크 전압은 450 mV, 신호대 잡음비는 7.2 였다.

• 한국염색가공학회지
• /
• 제12권2호
• /
• pp.103-110
• /
• 2000

To examine the physical properties of POY through the microstructure control, the crystal structure such as the crystallinity, the crystallite size, the orientation, the shrinkage, the tensile properties, and the thermal stress of POY(80/48, SD) were examined at different draw ratios and annealing temperatures. From the examination following conclusions were obtained : 1. The crystallinity was more effected by the heat setting temperature than by the draw ratio. The increasing rate was greatest at the heat setting temperature range of $170~190^\circ{C}$. 2. The crystallite size perpendicular to the fiber axis was more effected by the annealing temperature at lower draw ratios. On the other hand, the crystal and amorphous orientations were more effected by the heat setting at higher draw ratios. 3. The boiling shrinkage did not change significantly, but the total shrinkage showed 13% at the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$. 4. The maximum thermal stress increased with increasing the draw ratio and decreasing the heat setting temperature in the temperature range of $170~210^\circ{C}$. At the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$, the maximum thermal stress found was 1.1gf/d. 5. In the heat setting temperature above $170^\circ{C}$ after the drawing, the crystallinity, the crystallite size, the orientation, and the strength increased with increasing temperature, but the shrinkage and the maximum thermal stress decreased with increasing temperature.

• 한국진공학회지
• /
• 제9권3호
• /
• pp.258-262
• /
• 2000

$YMnO_3$박막은 고주파 스퍼터를 사용하여 Si(100)과 $Y_2O_3$/si(100)기판에 증착하였다. 증착시에 산소 분압의 조건과 열처리 온도는 YMnO$_3$ 박막의 결정성과 그 메모리 윈도우의 특성에 매우 중요한 영향을 주었다. XRD 측정 결과 산소 분압 0%에서 증착후 $870^{\circ}C$에서 1시간 동안 후열처리한 $YMnO_3$ 박막은 c-축을 따라 매우 잘 배향되었음을 확인하였다. 반면 산소분압 20%에서 Si(100)과 $Y_2O_3$/Si(100) 기판위에 증착된 $YMnO_3$박막의 결정화는 XRD측정 결과 $Y_2$O$_3$ peak가 보이는 것으로 보아 YMnO$_3$박막내에 과잉의 $Y_2O_3$가 c-축으로의 배향을 억제하는 것을 알 수 있다. 특히 산소분압 0%에서 증착한 Pt/$YMnO_3/Y_2O_3$/Si 구조에서의 메모리 윈도우 특성은 c-축으로 잘 배향된 결과로 인해 인가전압 2~12V에서 0.67-3.65V이었으며 이는 $Y_2O_3$/si 기판위에 산소분압 20%에서 증착한 박막 (0.19~1.21V)보다 동일한 인가전압에서 3배 정도의 큰 메모리 윈도우 특성을 보였다.

• Progress in Superconductivity
• /
• 제9권1호
• /
• pp.5-10
• /
• 2007

We prepared four different $MgB_2$ films on $Al_2O_3$ by hybrid physical chemical vapor deposition method with thicknesses ranging from $0.65\;{\mu}m$ to $1.2\;{\mu}m$. X-ray diffraction patterns confirm that all the $MgB_2$ films are c-axis oriented perpendicular to $Al_2O_3$ substrates. The superconducting onset temperature of $MgB_2$ films were between 39.39K and 40.72K. The residual resistivity ratio of the $MgB_2$ films was in the range between 3.13 and 37.3. We measured the angle dependence of critical current density ($J_c$) and resistivity, and determined the upper critical field ($H_{c2}$) from the temperature dependence of the resistivity curves. The anisotropy ratios defined as the ratio of the $H_{c2}$ parallel to the ab-plane to that perpendicular to the ab-plane were in the range of 2.13 to 4.5 and were increased as the temperature was decreased. Some samples showed increase of $J_c$ and decrease of resistivity when a magnetic field in applied parallel to the c-axis. We interpret this angle dependence in terms of enhanced flux pinning due to columnar growth of $MgB_2$ along the c-axis.

• Journal of Magnetics
• /
• 제16권3호
• /
• pp.220-224
• /
• 2011

Die-upset magnets from a mechanically-milled Pr(Co,In)$_5$-type alloy are known to have a peculiar texture; the easy magnetization axis (c-axis) is perpendicular to the pressing direction. This peculiar texture is thought to be linked closely to the anisotropic mechanical properties of Pr(Co,In)$_5$-type hexagonal compounds. The hardness of the Pr(Co,In)$_5$-type crystal was measured using selectively grown grains in an annealed $Pr_{17}Co_{82}In_1$ alloy button, and the crystallographic orientation was determined by observing the magnetic domain image. The hardness (549 VHN) on the plane with a 'cogwheel'-type domain image was significantly higher than that (510 VHN) on the plane with a 'cigar'-type domain image, indicating that the inter-layer bonding force between the (000l) basal planes is stronger than that between the (hki0) planes. This suggests that the most probable slip plane is the (hki0) plane parallel to the c-axis. During die-upsetting of the Pr(Co,In)$_5$-type alloys the deformation proceeds by (hki0) plane slip, and the c-axis rotates to ultimately become oriented perpendicular to the pressing direction. It is proposed that the peculiar texture in the die-upset Pr(Co,In)$_5$-type magnets is probably developed by slip deformation of the (hki0) plane of the Pr(Co,In)$_5$-type grains.