• Journal of the Korean Wood Science and Technology
• /
• 제24권3호
• /
• pp.101-109
• /
• 1996

Effects of process variables were evaluated in physical properties of the wood fiber-thermoplastic fiber composites using nonwoven web method. Turbulent air mixer using compressed air was employed to mix wood fiber with two types of thermoplastic polypropylene and nylon 6 fibers. The optimal hot press temperature and time were found to be $190^{\circ}C$ and 9 minutes in wood fiber-polypropylene fiber composite and to be $220^{\circ}C$ and 9 minutes in wood fiber-nylon 6 fiber composite. As the density of wood fiber-polypropylene fiber composite and wood fiber-nylon 6 fiber composite increased, the physical properties were improved The density appeared to be the most significant factor on physical properties in the statistical analysis. The composition ratio of polypropylene or nylon 6 fiber to wood fiber was considered not to be statistically significant factor. The thickness swelling decreased somewhat in wood fiber-polypropylene fiber composite and wood fiber-nylon 6 fiber composite as the content of synthetic fiber increased. As the increase of mat moisture content, dimensional stability was improved in wood fiber-polypropylene fiber composite but not in wood fiber-nylon 6 fiber composite.

• Steel and Composite Structures
• /
• 제12권3호
• /
• pp.261-273
• /
• 2012

This study proposes and examines a circular composite bridge pier for seismic resistance. The axial and flexural strengths of the proposed bridge pier are provided by the longitudinal reinforcing bars and the concrete, while the transverse reinforcements used in the conventional reinforced concrete pier are replaced by the steel tube. The shear strength of this composite pier relies on the steel tube and the concrete. This system is similar to the steel jacketing method which strengthens the existing reinforced concrete bridge piers. However, no transverse shear reinforcing bar is used in the proposed composite bridge pier. A series of experimental studies is conducted to investigate the seismic resistant characteristics of the proposed circular composite pier. The effects of the longitudinal reinforcing bars, the shear span-to-diameter ratio, and the thickness of the steel tube on the performance of strength, ductility, and energy dissipation of the proposed pier are discussed. The experimental results show that the strength of the proposed circular composite bridge pier can be predicted accurately by the similar method used in the reinforced concrete piers with minor modification. From these experimental studies, it is found that the proposed circular composite bridge pier not only simplifies the construction work greatly but also provides excellent ductility and energy dissipation capacity under seismic lateral force.

• 한국산학기술학회논문지
• /
• 제8권2호
• /
• pp.195-200
• /
• 2007

최소선폭 $0.1{\mu}m$ 이하의 살리사이드 공정을 상정하여 $10nm-Ni_{0.5}Co_{0.5}/70\;nm-Poly-Si/200\;nm-SiO_2$ 구조로부터 쾌속 열처리를 이용해서 실리사이드 온도를 $600{\sim}1100^{\circ}C$까지 변화시키면서 복합실리사이드를 제조하고 이들의 면저항의 변화와 미세구조의 변화를 면저항 측정기와 TEM 수직단면, 오제이 두께 분석으로 확인하였다. 기존의 동일한 공정으로 제조된 니켈실리사이드에 비해 제안된 니켈 코발트 복합실리사이드는 $900^{\circ}C$까지 저저항을 유지시킬 수 있는 장점이 있었고 20nm 두께의 균일한 실리사이드 층을 폴리실리콘 상부에 형성시킬 수 있었다. 고온 처리시에는 복합실리사이드와 실리콘의 전기적으로 상분리되는 혼합현상으로 고저항 특성이 나타나는 문제를 확인하였다. 제안된 NiCo 합금 박막을 70nm 높이의 폴리실리콘 게이트를 가진 디바이스에 $900^{\circ}C$이하의 실리사이드화 온도에서 효과적으로 산리사이드 공정의 적용이 기대되었다.

• 한국재료학회지
• /
• 제2권6호
• /
• pp.461-467
• /
• 1992

최근 선진국에서 강화되고 있는 CAFE(Corporate Average Fuel Economy :기업평균연비) 규제를 극복하기 위해서는 차량의 경량화가 필수적이며 이를 위해 기존의 금속재료에 비하여 비강도, 탄성계수, 인성등이 우수한 기계적 성질을 가지면서 고분자 기지의 복합재료에 비해서 고온강도, 전기 및 열전도도와 내마모성이 우수한 금속기지 복합재료의 개발은 필수적이고도 중요한 위치를 차지한다. 따라서 본 연구에서는 자동차용 부품재 및 일반산업용 재료로 사용되고 있는 AC4A Al합금에 Si$C_w$prefohm을 용탕 단조법으로 강화하여 복합재료를 제조란 후 matrix와 함계 기계적성질, 마멸특성, 조직실험을 행한 결과 용탕 단조법에 의한 AC4A/Si$C_w$ 복합재료의 최적 제조조건은 용탕온도 80$0^{\circ}C$, 금형은도 40$0^{\circ}C$, preform은도 750-80$0^{\circ}C$, 가압압력 75MPa이었으며 Si$C_w$강화재가 I/M재에 비하여 경도값은 두배이상으로 상승하였고 Si$C_w$ 20v/o에서는 가압에 의한 큰 효과는 없었다.

• Composites Research
• /
• 제28권4호
• /
• pp.212-218
• /
• 2015

본 연구에서는 AFP 장비를 이용하여 대형 복합재 스파 구조를 제작하고, 스파 구조에서 가장 취약한 부분인 코너부(Corner radius)에 대한 굽힘강도 시험과 해석을 수행하였다. 국내에서 AFP를 이용한 제품 제작기술이 보편화되지 않은 초기단계임을 고려하여, 복합재 스파 제작을 위한 맨드릴 설계 및 해석에서 구조 검증시험에 이르기까지의 전 과정을 요약, 정리하였다. 맨드릴 설계에서는 자중과 장비 하중에 의한 처짐, 응력, 열변형, 고유진동수 등을 고려하였다. 대상 시제품은 대형 C-스파이고 AFP로 제작한 후 오토클레이브에서 성형하였다. 제품의 성능 확인을 위해 스파 코너부에서 시편을 채취하여 4점 굽힘시험과 비선형 강도해석을 수행하여 제작된 구조물이 이론적 구조강도에 근접하는 강도를 보이는지 점검하였다. 연구결과, 제안된 공정을 사용하여 제작한 대형 C-스파의 코너부는 최초층 파손이론을 사용한 이론적 강도대비 20% 이내의 차이를 보이는 것을 확인하였고, 향후 양산용 대형 복합재 구조물 제작에 적용될 수 있는 가능성을 확인하였다.

• Carbon letters
• /
• 제6권4호
• /
• pp.234-242
• /
• 2005

Bending and tensile properties of 2D cross-ply C/C composites with processing heat treatment temperature (HTT) are evaluated. C/C composites used are made from two types of PAN based T700 and M40 carbon fibers with phenolic resin as carbon matrix precursor. Both the types of composites are heat treated at different temperatures (ranging from 750 to $2800^{\circ}C$) and characterized for bending and tensile properties. It is observed that, real density and open porosity increases with HTT, however, bulk density does show remarkable change. The real density and open porosity are higher in case T-700 carbon fiber composites at $2800^{\circ}C$, even though the density of M40 carbon fiber is higher. Bending strength is considerably greater than tensile strength through out the processing HTT due to the different mode of fracture. The bending and tensile strength decreases in both composites on $1000^{\circ}C$ which attributed to decrease in bulk density, thereafter with increase in HTT, bending and tensile strength increases. The maximum strength is in T700 fiber based composites at HTT $1500^{\circ}C$ and in M40 fiber based composites at HTT $2500^{\circ}C$. After attending the maximum value of strength in both types of composite at deflection HTT, after that strength decreases continuously. Decrease in strength is due to the degradation of fiber properties and in-situ fiber damages in the composite. The maximum carbon fiber strength realization in C/C composites is possible at a temperature that is same of fiber HTT. It has been found first time that the bending strength more or less 1.55 times higher in T700 fiber composites and in M40 fiber composites bending strength is 1.2 times higher than that of tensile strength of C/C composites.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1228-1229
• /
• 2008

The composites were fabricated 61[vol.%] ${\beta}$-SiC and 39[vol.%] $TiB_2$ powders with the liquid forming additives of 12[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid by pressure or pressureless annealing at 1,650[$^{\circ}C$] for 4 hours. Reactions between SiC and transition metal $TiB_2$ were not observed in the microstructure and the phase analysis of the SiC-$TiB_2$ electroconductive ceramic composites. Phase analysis of SiC-$TiB_2$ composites by XRD revealed mostly of ${\alpha}$-SiC(6H), $TiB_2$, and In Situ $YAG(Al_5Y_3O_{12})$. The relative density, the flexural strength and the Young's modulus showed the highest value of 88.32[%], 136.43[MPa] and 52.82[GPa] for pressure annealed SiC-$TiB_2$ composites at room temperature. The electrical resistivity showed the lowest value of 0.0162[${\Omega}{\cdot}cm$] for pressure annealed SiC-$TiB_2$ composite at 25[$^{\circ}C$]. The electrical resistivity of the pressure annealed SiC-$TiB_2$ composite was positive temperature coefficient resistance (PTCR) but the electrical resistivity of the pressureless annealed SiC-$TiB_2$ composites was negative temperature coefficient resistance(NTCR) in the temperature ranges from 25[$^{\circ}C$] to 700[$^{\circ}C$].

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.364-371
• /
• 2013

The sintering behavior of monolithic SiC is examined using the binary sintering additive of $Al_2O_3$-rare earth oxide ($RE_2O_3$, where RE = Sc, Nd, Dy, Ho, or Yb). Through hot pressing at 20 MPa and $1750^{\circ}C$ for 1 h in an Ar atmosphere for 52 nm fine ${\beta}$-SiC powder added with 5 wt% sintering additive, a SiC density of > 97% is achieved, which indicates the effectiveness of $Al_2O_3-RE_2O_3$ system as a sintering of additive for SiC. Based on this result, 7 wt% of $Al_2O_3-Sc_2O_3$ is tested as an additive system for the fabrication of a continuous SiC fiber-reinforced SiC-matrix composite ($SiC_f$/SiC). Electrophoretic deposition combined with the application of ultrasonic pulses is used to efficiently infiltrate the matrix phase into the voids of $Tyranno^{TM}$-SA3 fabric. After hot pressing, a composite density of > 97% is obtained, along with a maximum flexural strength of 443 MPa.

• The Journal of Advanced Prosthodontics
• /
• 제3권4호
• /
• pp.216-220
• /
• 2011

PURPOSE. Heat of composite polymerization (HP) indicates setting efficacy and temperature increase of composite in clinical procedures. The purpose of this in vitro experimental study was to evaluate the effects of 5 temperatures on HP of two new composites. MATERIALS AND METHODS. From each material (Core Max II [CM] and King Dental [KD]), 5 groups of 5 specimens each were prepared and their total HPs (J/gr) were measured and recorded, at one of the constant temperatures $0^{\circ}C$, $15^{\circ}C$, $23^{\circ}C$, $37^{\circ}C$ and $60^{\circ}C$ ($2{\times}5{\times}5$ specimens) using a differential scanning calorimetry (DSC) analyzer. The data were analyzed using a two-way ANOVA, a Tukey's test, an independent-samples ttest, and a linear regression analysis (${\alpha}=0.05$). RESULTS. No polymerization reactions occurred at $0^{\circ}C$; then this temperature was excluded from statistical analyses. The mean HP of the remaining 20 KD specimens was $20.5{\pm}14.9$ J/gr, while it was $40.7{\pm}12.9$ J/gr for CM. The independent-samples t-test showed that there were significant differences between the HP of the two materials at the temperatures $15^{\circ}C$ (P=.0001), $23^{\circ}C$ (P=.0163), $37^{\circ}C$ (P=.0039), and $60^{\circ}C$ (P=.0106). Linear regression analysis showed statistically significant correlations between environment temperatures and HP of CM ($R^2=0.777$). CONCLUSION. Using CM is advantageous over conventional composite because of its better polymerization capacity. However due to its high HP, further studies should assess its temperature increase in vivo. Preheating KD is recommended. Refrigerating composites can negatively affect their polymerization potential.

• Composites Research
• /
• 제34권5호
• /
• pp.311-316
• /
• 2021

본 연구에서는 3 wt.%, 10 wt.% Cr이 함유된 Fe-합금 분말을 기지 금속으로 하여 분말야금공정을 통해 TiC/steel 금속복합재료를 제조하였다. 이후 복합재료의 기계적 물성에 미치는 열처리의 영향을 고찰하고자, 어닐링 열처리 및 칭-템퍼링 열처리를 실시하였다. 인장, 압축 그리고 항절력 시험과 미세조직 분석을 통하여 Cr 함량 및 열처리 조건에 따른 미세조직의 변화와 구조적 강도 변화의 연관성을 고찰하였다. 10 wt.% Cr을 함유한 TiC/steel의 경우, TiC/steel 계면에서 형성된 조대한 Cr carbide의 영향으로 상온 인장강도 및 항절력이 크게 저하하였다. 이에 반해 압축강도에서는 Cr이 3 wt.%, 10 wt.% 함유된 TiC/steel 복합재료 모두 Cr carbide의 유무와 관계없이 어닐링 열처리 시편에 비해 칭-템퍼링 열처리 후 약 4 GPa에 달하는 높은 압축강도를 보였다.