• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.11-18
• /
• 2016

This study focused on examining the possibility for recycling of Fe-Si electric sheet. We manufactured Fe-6.5Si mother alloy using by Fe-Si electric sheet scrap for transformer core materials. And then, soft magnetic alloy powder which diameter and shape were $45{\sim}150{\mu}m$ and sphere type was prepared by gas atomization process. As we compared to commercial Fe-6.5Si powder, its diameter distribution and microstructure of recycled powder was a similar. To investigate the possibility of reusing the soft magnetic composite sheet for electronics, recycled powder was treated to have a high aspect ratio (AR), and we finally obtained the 65~66 AR and $2.3{\mu}m$ thickness powder. To release the residual stress of powder, heat treatment was conducted under $300{\sim}400^{\circ}C$, $N_2$ gas. And then, soft magnetic sheet was made by tape casting process using by those powders. After the density and permeability of tape was measured, and we confirmed that the recycled Fe-Si electric sheet scrap was possible to reuse the soft magnetic materials of electronics.

• Steel and Composite Structures
• /
• v.35 no.5
• /
• pp.611-625
• /
• 2020

Experimental investigation and finite element analysis of corroded cold-formed steel (CFS) columns are presented. 11 tensile coupon specimens and 6 stub columns of corroded CFS that had a channel section of C160x60x20 were subjected to monotonic tensile tests and axial compression tests, respectively. The degradation laws of the mechanical properties of the tensile coupon specimens and stub columns were analysed. An appropriate finite element model for the corroded CFS columns was proposed and the influence of local corrosion on the stability performance of the columns was studied by finite element analysis. Finally, the axial capacity of the experimental results was compared with the predictions obtained from the existing design specifications. The results indicated that with an increasing average thickness loss ratio, the ultimate strength, elastic modulus and yield strength decreased for the tensile coupon specimens. Local buckling deformation was not noticeable until the load reached about 90% of the ultimate load for the non-corroded columns, while local buckling deformation was observed when the load was only 40% of the ultimate load for the corroded columns. The maximum reduction of the ultimate load and critical buckling load was 57% and 81.7%, respectively, compared to those values for the non-corroded columns. The ultimate load of the columns with web thickness reduced by 2 mm was 53% lower than that of the non-corroded columns, which indicates that web corrosion most significantly affects the bearing capacity of the columns with localized corrosion. The results predicted using the design specifications of MOHURD were more accurate than those predicted using the design specifications of AISI.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.2
• /
• pp.118-123
• /
• 2017

PURPOSE. To investigate the effect of non-thermal atmospheric pressure plasma (NTAPP) treatment on shear bond strength (SBS) between resin cement and colored zirconia made with metal chlorides. MATERIALS AND METHODS. 60 zirconia specimens were divided into 3 groups using coloring liquid. Each group was divided again into 2 sub-groups using plasma treatment; the experimental group was treated with plasma, and the control group was untreated. The sub-groups were: N (non-colored), C (0.1 wt% aqueous chromium chloride solution), M (0.1 wt% aqueous molybdenum chloride solution), NP (non-colored with plasma), CP (0.1 wt% aqueous chromium chloride solution with plasma), and MP (0.1 wt% aqueous molybdenum chloride solution with plasma). Composite resin cylinders were bonded to zirconia specimens with MDP-based resin cement, and SBS was measured using a universal testing machine. All data was analyzed statistically using a 2-way ANOVA test and a Tukey test. RESULTS. SBS significantly increased when specimens were treated with NTAPP regardless of coloring (P<.001). Colored zirconia containing molybdenum showed the highest value of SBS, regardless of NTAPP. The molybdenum group showed the highest SBS, whereas the chromium group showed the lowest. CONCLUSION. NTAPP may increase the SBS of colored zirconia and resin cement. The NTAPP effect on SBS is not influenced by the presence of zirconia coloring.

• Computers and Concrete
• /
• v.15 no.6
• /
• pp.951-972
• /
• 2015

The focus of the present study is to investigate both local and global behaviour of a precast concrete sandwich panel. The selected prototype consists of two reinforced concrete layers coupled by a system of cold-drawn steel profiles and one intermediate layer of insulating material. High-definition nonlinear finite element (FE) models, based on 3D brick and 2D interface elements, are used to assess the capacity of this technology under shear, tension and compression. Geometrical nonlinearities are accounted via large displacement-large strain formulation, whilst material nonlinearities are included, in the series of simulations, by means of Von Mises yielding criterion for steel elements and a classical total strain crack model for concrete; a bond-slip constitutive law is additionally adopted to reproduce steel profile-concrete layer interaction. First, constitutive models are calibrated on the basis of preliminary pull and pull-out tests for steel and concrete, respectively. Geometrically and materially nonlinear FE simulations are performed, in compliance with experimental tests, to validate the proposed modeling approach and characterize shear, compressive and tensile response of this system, in terms of global capacity curves and local stress/strain distributions. Based on these experimental and numerical data, the structural performance is then quantified under various loading conditions, aimed to reproduce the behaviour of this solution during production, transport, construction and service conditions.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.28-36
• /
• 2014

We studied the green synthesis and antibacterial activity of paper coated with chitosan-silver (Ag) green nanocomposites for packaging applications. Green synthesis of Ag nanoparticles (AgNPs) was achieved by a chemical reaction involving a mixture of chitosan-silver nitrate ($AgNO_3$) in an autoclave at 15 psi, $121^{\circ}C$, for 30 min. AgNPs and their formation in chitosan was confirmed by UV-Vis spectroscopy, transmission electron microscopy (TEM) and dynamic light scattering (DLS). As-prepared chitosan-AgNPs composite materials were coated on manila paper using Meyer rod. Surface morphology and Ag contents in coating layer were characterized by field emission scanning electron microscopy (FESEM) and energy dispersive spectroscopy (EDS). The mechanical properties such as tensile strength and elongation were significantly affected by coating with chitosan-AgNPs. The antibacterial test of coated paper was performed qualitatively and quantitatively against Escherichia coli (E. coli). It was shown to be effective in suppressing the growth of E. coli with increasing Ag contents on the surface of coated paper and more than 95 R (%) of antimicrobial rate was obtained at chitosan-AgNPs coated papers.

• Advances in aircraft and spacecraft science
• /
• v.3 no.4
• /
• pp.427-445
• /
• 2016

Star sensors are the attitude estimation sensors of the satellite orbiting in its path. It gives information to the control station on the earth about where the satellite is heading towards. It captures the images of a predetermined reference star. By comparing this image with that of the one captured from the earth, exact position of the satellite is determined. In the process of imaging, stray lights are eliminated from reaching the optic lens by the mechanical enclosures of the star sensors called Baffles. Research in space domain in the last few years is mainly focused on increased payload capacity and reduction in launch cost. In this paper, a star sensor baffle made of Aluminium is considered for the study. In order to minimize the component weight, material wastage and to improve the structural performance, an alternate material to Aluminium is investigated. Carbon Fiber Reinforced Polymer is found to be a better substitute in this regard. Design optimisation studies are carried out by adopting suitable design modifications like implementing an additional L-shaped flange, Upward flange projections, downward flange projections etc. A better configuration of the baffle, satisfying the design requirements and achieving manufacturing feasibility is attained. Geometrical modeling of the baffle is done by using UNIGRAPHICS-Nx7.5(R). Structural behavior of the baffle is analysed by FE analysis such as normal mode analysis, linear static analysis, and linear buckling analysis using MSC/PATRAN(R), MSC-NASTRAN(R) as the solver to validate the stiffness, strength and stability requirements respectively. Effect of the layup sequence and the fiber orientation angle of the composite layup on the stiffness are also studied.

• Journal of the Korean Ceramic Society
• /
• v.55 no.6
• /
• pp.556-561
• /
• 2018

In this study, we performed a microwave sintering (MWS) of $Al_2O_3$ ceramic and $Al_2O_3$-based composites with nominal contents of graphene nanoplatelets (GPLs) of 0.2, 0.4, 0.6, and 0.8 vol%. The GPL dispersion in N-methyl pyrroleketone was optimized to deagglomerate the GPLs without damaging their structure. Dense composites were then obtained by MWS at $1500^{\circ}C$ for 30 min. The effects of different GPL contents on the phase compositions, microstructures, and mechanical properties of the composites were investigated. The microstructures of the composites became finer with the incorporation of the GPLs. The well-dispersed GPL fillers led to higher sintered densities in the composites. The optimal mechanical properties were achieved with 0.4 vol% GPLs. For this sample, the hardness, fracture toughness, and bending strength were $2000kgf/mm^2$, $6.19MPa{\cdot}m^{1/2}$, and 365.10 MPa, respectively. The addition of GPL could improve the microstructure of the $Al_2O_3$ ceramic and has potential to improve the fracture toughness of the ceramics.

• Journal of the Korean Ceramic Society
• /
• v.44 no.2 s.297
• /
• pp.110-115
• /
• 2007

The effects of $TiO_2$ in the glasses on the shrinkage and dielectric properties of BNT-glass composites have been investigated. Without $TiO_2$ addition, BNT-glass composite showed two humps in the shrinkage curve, which are related with crystallization of $BaTi(BO_3)_2\;and\;Bi_4Ti_3O_{12}$. However, the increase of $TiO_2$ addition resulted in the decrease of 2nd hump in the shrinkage. The increased dielectric constant with $TiO_2$ addition might be due to the reduced crystallization of $Bi_4Ti_3O_{12}$. A dielectric constant of 52, a quality factor of 5088 GHz, and a temperature coefficient of resonant frequency of $-0.16ppm/^{\circ}C$ were obtained for a specimen containing $TiO_2$-added glasses, without sacrificing the benefits of high ${\varepsilon}_r$ and low TCF of BNT ceramics.

• Korean journal of food and cookery science
• /
• v.25 no.2
• /
• pp.243-251
• /
• 2009

Changes in pH and acidity were investigated in kimchi containing different amounts of added onion and/or pear during fermentation at $10^{\circ}C$. As the fermentation period increase, the pH and sugar contents of the onion and/or pear kimchi were higher compared to the control kimchi. However, the acidity of the kimchi containing onion and/or pear was lower than that of the control. To enhance the acceptance of kimchi, the optimal conditions for the addition of onion and pear were evaluated with the central composite design, ANOVA, and response surface methodology. According to variations in the mixing ratio of onion and pear, smell, taste and overall acceptability differed significantly, but the appearance and texture were not different. The optimal levels of onion and pear, predicted on the basis of each corresponding sensory parameters for kimchi, were $4.55{\sim}5.00%$ and $0{\sim}0.30%$ for smell, 2.61% and 2.38% for taste and 2.78% and 2.57% for overall acceptability, respectively.

• Korean Journal of Food Science and Technology
• /
• v.37 no.3
• /
• pp.431-437
• /
• 2005

Overall experiments were planned by central composite design, and results were analyzed by response surface methodology (RSM) to determine effects of three independent variables, temperature ($X_{1}$), extraction time ($X_{3}$), and pressure ($X_{3}$), on yield of sesame oil extract (Y). Regression equation model optimized by response surface analysis was: Y (sesame oil) = $-3.89+0.07X_{1}+0.03X_{2}+0.0006X_{3}-0.0007X_{1}^{2}-0.0002X_{2}X_{1}-0.00008X_{2}^{2}+0.000004X_{3}X_{1}+0.0000009X_{3}X_{2}-0.00000009X_{3}^{2}$. According to RSM analysis, optimum extracting conditions of temperature, time, and pressure were $45.89^{\circ}C$, 131.89 min, and 34228.41 kPa, respectively, and statistical maximum yield of sesame oil was 96.27%. Fatty acid composition of sesame oil showed sesame oil extracted by Supereritical Fluid $CO_{2}$ contained lower levels of palmitic, stcaric, and oleic acids and higher levels or palmitoleic and linoleic acids than commercial sesame oil. Commercial and extracted sesame oils were analyzed by electronic nose composed of 12 different metal oxide sensors. Obtained data were interpreted by statistical method of MANOVA. Sensitivities of sensors from electronic nose were analysed by principal component analysis. Proportion of first principal component was 99.92%. All sesame oils showed different odors (p < 0.05).