• Journal of Welding and Joining
• /
• 제34권1호
• /
• pp.68-74
• /
• 2016

Adoption of narrow gap welding shall be increased for the butt joint of thick plate, because the deformation and welding cost is reduced by decrease of cross-sectional area. However, sometimes narrow gap causes defects such as lack of fusion since it has small groove angle and narrow groove width. Therefore, GMAW, GTAW and SAW process shall be adopted to narrow gap welding with small bead hight and low deposition rate. In this study, Super-TIG welding using C-type strip was applied to semi-narrow gap butt joint in order to increase the welding productivity. High deposition rate 10kg/hr was obtained by high current 600A without undercut, humping bead and other welding defects. Measuring the mean and standard deviation of the melting depth to evaluate the developed processes, the fusion line type was determined by measuring the difference between maximum and minium melting depth. Furthermore, a model on arch fusion line and linear fusion line was suggested in order to prevent LF on groove wall in narrow gap butt welding.

• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.70-75
• /
• 2000

The weld seam tracking system for arc welding process uses various kinds of sensors such as arc sensor, vision sensor, laser displacement and so on. Among the variety of sensors available, electro-magnetic sensor is one of the most useful methods especially in sheet metal butt-joint arc welding, primarily because it is hardly affected by the intense arc light and fume generated during the welding process, and also by the surface condition of weldments. In this study, a dual-electromagnetic sensor, which utilizes the induced current variation in the sensing coil due to the eddy current variation of the metal near the sensor, was developed for arc welding of sheet metal butt-joints. The dual-electromagnetic sensor thus detects the offset displacement of weld line from the center of sensor head even though there's no clearance in the joint. A set of design variables of the sensor were determined for the maximum sensing capability through the repeated experiments. Seam tracking is performed by correcting the position of sensor to the amount of offset displacement every sampling period. From the experimental results, the developed sensor showed the excellent capability of weld seam detection when the sensor to workpiece distance is near less than 5 mm, and it was revealed that the system has excellent seam tracking ability for the butt-joint of sheet metal.

• 폴리머
• /
• 제24권1호
• /
• pp.23-28
• /
• 2000

Solvent 용접에 따른 무정형 고분자 폴리스티렌/폴리스티렌 계면의 접착강도의 변화를 butt joint실험을 통하여 살펴보았다. 폴리스티렌과 용해도 상수가 유사한 용매를 계면에 코팅함으로써 계면 분자쇄의 유동성 증가와 계면의 거침정도의 변화에 따른 접촉표면의 증가로 인하여 접착 강도가 증가함을 확인하였다. 사용용매의 비등점이 접착온도보다 높은 경우, 접착강도의 증가는 용매에 의한 분자쇄의 유동성 증가에 기인되는 반면 용매의 비등점이 접착온도에 비해 낮을 경우 접착강도의 증가는 용매에 의한 접촉표면의 증가에 의존함을 알 수 있었다. 접착온도가 높을수록, 접착시간이 길어질수록 접착강도는 증가되며, 사용용매가 접착강도에 미치는 영향은 감소함을 알 수 있었다.

• 복합신소재구조학회 논문집
• /
• 제2권2호
• /
• pp.13-19
• /
• 2011

본 연구에서는 강재가 맞대기 이음으로 연결될 경우 CFRP(Carbon Fiber Reinforced Plastic) 쉬트(sheet)를 맞대기 이음부에 접착할 경우 강재 및 CFRP 쉬트에 발생하는 응력을 해석하였다. CFRP 쉬트로 보강한 경우 접착제의 두께, 강재와의 접착 길이, CFRP 강도 변화를 매개변수로 사용하여 이 매개변수에 변화에 따른 이음부의 응력분포를 분석하였다. 또한 CFRP를 여러 층으로 접착할 경우 각 층의 강도를 다르게 변화시켜 맞대기 이음부에 유리한 응력분포를 나타내는 CFRP의 강도를 제시하였다. 본 연구를 위해 빠른 수렴성을 가지며 왜곡된 요소형상에서도 정확한 응력결과를 보이는 강화변형률장(Enhanced Assumed Strain Field)을 사용한 평면변형률 유한요소에 대한 프로그램을 작성하였다.

• Journal of Welding and Joining
• /
• 제20권2호
• /
• pp.95-101
• /
• 2002

After high power lasers are avaliable in the commercial market, the number of applications of the laser welding has been increased in manufacturing industries. Although the tailored blank laser welding of butt jointed steel sheets is well known recently in the automotive industries, the lap joint laser welding is a new technology to the automotive manufacturing people as well as the design people. But the deep penetration laser welding seems to be preferred to the partial penetration welding for the lap joint welding in the automotive manufacturers because the partial penetration is a serious deflect for the butt joint. In this study, the feasibility of partial penetration welding fur the lap joint $CO_2$ laser welding was studied fur the 1mm thick 390MPa high strength steel sheets for automotive bodies. The process window of the lap joint partial penetration welding was obtained from experiments with the gap size and the welding speed as process parameters. The partial penetration welding was found excellent on the basis of the tensile shear strength and sectional geometry. The bead width, input energy Per volume, tensile-shear strength, deformation energy and the sectional geometries after tensile-shear tests of partial penetration welded specimens are compared with those of full penetration welded specimens with a series of gaps and welding speeds.

• International Journal of Advanced Culture Technology
• /
• 제3권1호
• /
• pp.179-187
• /
• 2015

This study presents the experimental results of the Friction Stir Welding (FSW) of AA6063 aluminum alloy and AISI304 stainless steel butt joint by varying the welding parameters such as the rotating speed and the welding speed. The main results are as follows. The variation of the welding parameters produced various characteristic interfaces and had distinct influences on the joint properties. Increasing the rotating speed and the welding speed decreased the joint tensile strength because it produced the defect on the joint interface. The optimum welding parameter that could produce the sound joint was a rotating speed of 750 rpm and the welding speed of 102 mm/min with the tensile strength of 71 MPa.

• 한국가구학회지
• /
• 제17권2호
• /
• pp.25-34
• /
• 2006

This experiment was carried out to investigate the high-frequency gluing characteristics of poly vinyl acetate emulsion adhesive(PVAc) on MDF edge-glued boards. The edge-glued boards were glued lengthwise with butt, scarf, or finger joint. The wastes of MDF boards were reused as board materials. The obtained results are summarized as follows; the bending strength of edge-glued MDF increased slightly with the HF heating time, but the economically desirable heating time was 6 minutes. The bending and tensile strength of edge-glued MDF were high with scarf, finger and butt joint, in order. The strength of finger jointed MDF showed 80% of scarf jointed MDF. The effects of location of finger joints on the bending strength of edge-glued MDF were larger than those of the numbers of finger joints. The bending strength of edge-glued MDF with one joint on the middle position showed 40% decrease in comparison with non-jointed MDF.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.43-49
• /
• 2004

In this study, a visual sensor system which can detect I-butt weld joint with height variation and includes a seam tracking algorithm was investigated. Three-dimensional position of an object can be acquired by using the method of distance measurement, i.e., an optical trigonometry which results from the spatial relations between the camera, the object and the structured light by a visible laser. Effects of laser intensity and iris number for the image quality as well as object material were investigated for the optical system design. For the image processing, a region of interest is defined from the whole image and a line image of laser is drew by using the gray level difference in the image. From the drew laser line, the weld joint can be recognized in searching the biggest point position calculated from the central difference method. Through a series of welding experiments, a good tracking performance was confirmed under GMA welding.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.81-91
• /
• 1997

In this study, a magnetic sensor to make use of eddy current was developed to detect the weld seam of butt joint in the sheet metal arc welding. This system consist of the sensor device for detecting the weld line, the servo control device for driving the weld torch movement and the control unit. A signal processing was applied to smooth the output signal of the sensor. The weld joint was determined by using a 1st order differential method. To improve tracking accuracy of the system, moving average method which has an effect of proportional and weighted integral control was applied to a series of the weld joint positions obtained above. The weld line for tracking was generated by using data regeneration algorithm. Based on these results, each servo motor was controlled by pulse generator. From experimental results, it was revealed that this system has excellent detecting ability for weld line and seam tracking ability.

• Restorative Dentistry and Endodontics
• /
• 제12권1호
• /
• pp.107-116
• /
• 1986

The primary aim of this study was to assess the effects of the margin designs and composite resins on the marginal leakage of Class V resin restorations. 60 Class V cavities with $90^{\circ}$ butt joint, 60 with $45^{\circ}$ bevel joint, and 60 with concave joint were prepared on the labial surfaces of 38 extracted anterior teeth and the buccal and lingual surfaces of 71 premolars, and classified as the butt group, bevel group and concave group, respectively. After completion of the cavity preparation, Heliosit${(R)}$ was filled in 20 butt joint cavities, 20 bevel joint cavities, and 20 concave cavities. And Hi-Pol$^{(R)}$ and Palfique$^{(R)}$ were filled in the same manner, respectively. After finishing, all specimens were subjected manually to 50 thermal cycles at $4^{\circ}C$, $37^{\circ}C$, and $60^{\circ}C$. They were immersed in 0.5% methylene blue solution for 24 hours, and buccolingually sectioned with sectioning machine. The sectioned specimens were examined under the light microscope. The results indicated the following: 1. The bevel group showed the least amount of marginal leakage compared with the other two design groups, but the statistical analysis showed no significant difference at the 95% confidence level. 2. Hi-Pol$^{(R)}$ group showed the most severe marginal leakage compared with the other composite resin materials, but there was no significant difference in the groups. 3. The bevel-Heliosit$^{(R)}$ subgroup, which was filled with Heliosit$^{(R)}$ in the beveled cavities, showed the least amount of marginal leakage, but there was no significance in all the subgroups.