• Journal of Korean Society for Quality Management
• /
• v.48 no.4
• /
• pp.597-608
• /
• 2020

Purpose: The purpose of this paper is to present a probability distribution of the burst pressure of API 5L X65 pipes for the reliability assessment of corroded gas pipelines. Methods: Corrosion is a major cause of weakening the residual strength of the pipe. The mean residual strength on the corrosion defect can be obtained using the burst pressure code. However, in order to obtain the pipe reliability, a probability distribution of the burst pressure should be provided. This study is concerned with estimating the burst pressure distribution using Monte Carlo simulation. A response surface method is employed to represent the distribution parameter as a model of the corrosion defect size. Results: The experimental results suggest that the normal or Weibull distribution should be suitable as the probability distribution of the burst pressure. In particular, it was shown that the probability distribution parameters can be well predicted by using the depth and length of the corrosion defect. Conclusion: Given a corrosion defect on the pipe, its corresponding burst pressure distribution can be provided at instant. Subsequently, a reliability assessment of the pipe is conducted as well.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.43-50
• /
• 2003

This paper describes the optical resource reservation protocol for Optical Burst Switching(OBS) networks, in which the burst sending time and the burst size at an ingress node are determined by the available resources between the ingress and egress nodes. Our scheme attempts to improve the burst contention resolution and optical channel utilization. We analyze the performance of the optical resource reservation protocol by using NS2 simulator.

• Convergence Security Journal
• /
• v.5 no.1
• /
• pp.45-52
• /
• 2005

In this paper, the development specification of the optical burst switching system (OBS) for next generation internet services is presented. The development specification includes the number of input/output nodes, the number of wavelengths, buffer capacity, the capacity/queue size of the controller and maximum burst assembly delay. From the performance parameters related to the OBS design, an mathematical model to maximize the throughput and minimize the data loss is presented, and then efficient heuristic algorithm is also presented to analyze the sensitivity of the system parameters.

• Journal of the Korean Society of Safety
• /
• v.15 no.3
• /
• pp.23-29
• /
• 2000

The objective of this paper is to study burst through the influence of overheating to affect a seamed container using the cookers with different materials and bottom sizes. Following result are drawn from this study; When bottom size of the roast meat had 24cm diameter, the upper part temperature of a seamed container was increased over $40^{\circ}C$. Therefore the cooker material without regard to cooker size had a great influence on the temperature of seamed container. For the natural stone plate which had bottom length 65cm, a seamed container was burst at the cooker temperature $801^{\circ}C$, the surface temperature of a burner $573^{\circ}C$. the upside temperature of seamed container $379^{\circ}C$, the downside temperature of seamed container $236^{\circ}C$ and ambient temperature $34^{\circ}C$. For the cooker of the same bottom area, the stone plate had greater influence on effect of temperature than aluminium cooker. Overheating had a great influence on the seamed container if the bottom or upside diameter of a cooker had been larger than a trivet.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.1
• /
• pp.117-124
• /
• 1998

As window sized increases, the throughput input-buffered packet switch with a window scheme improves on random traffic condition. However, the improvement diminishes quickly under bursty traffic. In this paper, we propose Burst Head Addressable FIFO mechanism and memory structure having search capability in unit of burst header to compensate the sensitiveness of the windowed scheme to bursty traffic. The performance of a input-buffered switch using the proposed Burst Header Addressable FIFO input buffer was analyzed using computer simulations. The maximum throughput of the conventional FIFO scheme approaches an asymptotic value 0.5 as mean burst length increases. The maximum throughput of the proposed scheme is greater than that of the conventional scheme for any mean burst length and window size.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.12
• /
• pp.2835-2842
• /
• 2013

In this paper, service differentiation scheme using optical buffer that is reduced in size with slow-light technology in optical burst switching networks is presented. In suggested scheme, each outport has buffer to store high-class burst only in case that all its wavelengths are occupied. When all wavelengths are being used, a new arriving high-class burst goes into the buffer and waits until a burst is serviced. As soon as a burst is serviced with a wavelength, the high-class burst at buffer is allocated to the free wavelength. In case that low-class burst is arriving under the same situation, it is not stored at the buffer but discarded. An analytical model is derived to analyze the performance of the suggested scheme and compare its performance with the conventional scheme such as preemption and deflection as well as no service differentiations.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.8B
• /
• pp.514-524
• /
• 2005

In optical burst switching(OBS) networks, the ingress edge router assembles packets in the same class queue into the appropriate size of burst. A burst control packet(BCP) is generated for channel reservation of corresponding data burst and sent earlier than the corresponding data burst with an offset time. Offset time is determined considering the number of hops from source to destination and the required quality of service(QoS). After offset time, the burst data is passed through tile pre-configured optical switches without any O/E/O conversion. But a failure in OBS networks may lead to the loss of bursts until the ingress nodes receive the failure indication signal. This results in a significant degradation in QoS. Therefore, in this paper, we propose a fault-tolerant node architecture based on sub-carrier multiplexing to reduce the effects of failure in OBS networks. The Performance of the proposed fault-tolerant node architecture exhibits considerable improvement as compared with the previous ones.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.3
• /
• pp.251-258
• /
• 2003

Optical Switching Matrix (OSM) or Optical Multistage Interconnection Networks (OMINs) comprising photonic switches have been studied extensively as important interconnecting blocks for Optical Cross Connects (OXC) based on Optical Burst Switching (OBS). A basic element of photonic switching networks is a 2$\times$2 directional coupler with two inputs and two outputs. This paper is concerned with the diagnosis of multiple crosstalk-faults in OSM. As the network size becomes larger in these days, the conventional diagnosis methods based on tests and simulation become inefficient, or even more impractical. We propose a simple and easily implementable algorithm for detection and isolation of the multiple crosstalk-faults in OSM. Specifically. we develop an algorithm for isolation of the source fault in switching elements whenever the multiple crosstalk-faults arc detected in OSM. The proposed algorithm is illustrated by an example of 16$\times$16 OSM.

• Journal of Digital Contents Society
• /
• v.8 no.4
• /
• pp.573-579
• /
• 2007

The Leaky Bucket mechanism has been studied in many areas. There has been much interest in flow control in High Speed Networks using the Leaky Bucket. In this paper, We propose the Burst Tokens Fill method that performs well in Leaky Bucket to control the average rate, peak rate, and burst size. This scheme show the improvement of performance. However, This method does not apply all area of applications. Especially application of on-off shape is appropriate and the other area must need to care for appling this scheme.

• YAKHAK HOEJI
• /
• v.44 no.6
• /
• pp.511-520
• /
• 2000

Various bupivacaine-loaded microspheres were prepared from poly (d,l-lactide) (PLA) or poly (d,l-lactic-co-glycolide) (PLGA) by a solvent evaporation method for the sustained release of drug. PLA and PLGA microspheres were prepared by w/o/w and w/o/o multiple emulsion solvent evaporation, respectively. The effects of process conditions such as emulsification speed, emulsifier type, emulsifier concentration and internal/external phase ratio on the characteristics of microspheres were investigated. The prepared microspheres were characterized for their drug loading, size distribution, surface morphology and release kinetics. Drug loading efficiency was higher in the microspheres prepared by w/o/o multiple emulsion than that by w/o/w multiple emulsion method, because the solubility of bupivacaine HCI was decreased in oil phase compared with water phase. The prepared microspheres had an average diameter between 1 and $2\;{\mu}M$ in all conditions of two methods. In morphology studies the PLA microspheres showed an irregular shape and smooth surface, but PLGA microspheres had a spherical shape and smooth surface. The release pattern of the drug from microspheres was evaluated on the basis of the burst effect and the extent of the release after 24h. The in vitro release of bupivacaine HCl from microspheres showed a large initial burst release and $60{\sim}80%$ release within one day in all conditions of two methods. The extents of the burst release against PLA and PLGA microspheres were $30{\sim}50%$ and $50{\sim}80%$ within 20min, respectively. This burst release seems to be due to the smaller size of microspheres and the solubility of drug in water.