• Journal of the Korean Society of Safety
• /
• v.5 no.1
• /
• pp.31-39
• /
• 1990

In this paper, the influence of the table speed, metal removal rate and grinding fluid on long wheel workpiece contact zone at high effect grinding was investigated by theoretical analyses and measuring the temperature, and discussed by the temperature distribution in grinding surface layer. Main results obtained are as follows, 1) Rega.dless of the table speed, the temperature gap of the workpiece(heat influx) is about 6-8 times as high in dry condition as in wet condition. 2) Good grinding condition can be obtained owing to the effect of grinding fluid without any burning defect under the condition of the metal removal rate(1.0mm$^3$/mm.s) in case of wet grinding. 3) When the depth from the surface layer is about 1.25-1.5mm under the condition of the slow table speed, surface temperature goes up higher as the table speed slows down, because long contact time is laked at the surface layer. 4) In case of the same metal removal rate, the lower the table speed becomes, the higher the surface temperature is, because grinding depth has a far more influence on wheel workpiece contact zone than the table speed.

• CELLMED
• /
• v.10 no.3
• /
• pp.23.1-23.5
• /
• 2020

Hasāh al-kuliya (Nephrolithiasis) is a common disease with a worldwide prevalence of about 12%. A 64 years old male patient, who visited the outpatient department of National Research Institute of Unani Medicine for Skin Disorder (NRIUMSD), Hyderabad, presented with complaints of mild dull pain in right flank region and burning micturition for one month. The ultrasonography of whole abdomen confirmed that there was one stone of 5 mm in calyceal region of each kidney. The patient was treated with the Unani regimen comprising of three formulations Majoon, Hajrul Yahood (5 gm), Jawarish Zarooni Sada (5 gm) and Habb-i-Mudir (1000 mg) for 6 months. The patient did not report any acute pain during the therapy. After 6 months of treatment the ultrasonography of whole abdomen showed absence of the stone from each kidney, ureters and bladder. There was no recurrence of the disease during next 6 months of post treatment follow up. This case report documented the successful medical treatment and prevention of recurrence of bilateral nephrolithiasis through Unani medicines. It concluded that the Unani regimen was effective and safe in the management of bilateral nephrolithiasis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.9
• /
• pp.1309-1316
• /
• 2003

A premixed-compression-ignition engine has been studied to improve the efficiency and to decrease exhaust emissions. However those systems have some difficulties for controlling combustion process. Radical is an activated chemical species formed by a chemical chain reaction between reactant and product. When the chain reactions occur, the energy bond of species is broken easily by the released radicals. The combustion chamber of the premixed-compression-ingnition engine is consist of a main chamber with lean premixture and a subchamber with rich premixture. Those are connected by narrow cylinderical connections. With ignition start in the subchamber, many different kinds of radical is jetted into the main chamber. The premixed gas in main chamber is quickly burned up by the radical ignition in multi-pionts. In this paper, the combustion phenomena in a constant volume combustor having a radical injector are numerically analyzed. The some constants in the reaction rate equation are adjusted by the experimental results tested in the same geometrical chamber. The code is applied on the two combustors in a wide range of equivalence ratio. The results show that the burning time is much shorter in the combustor having radical injector.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.225-227
• /
• 2002

Recently, there are many researches in several places for a new resource, ahead. Also, Water of $70\%$ in the earth it is interested and studied by around world. Long ago, in the side processing-use, it is making study the welding of Hydrogen- oxygen Gas, which is burned to acquired it(hydrogen+oxygen) by electric-disintegration into water, which has perfect-burning rather than exhaust carbon and it has excellent-sides in financials and efficiencies than existing-gas welding by sparking-characteristics of Hydrogen Oxygen gas. Therefore, with constant current source, it is intended to make a producing gas ratio through designing and making for the use of SCR rectifier of existing-formula and then in this paper it hopefully is coming up to characteristics of welding machine and producer of hydrogen oxygen gas with current-controlled type.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.225-228
• /
• 2007

The objective of this study is to characterize design parameters of rocket igniters for composite, double base and nitramine propellant. Arc image furnace and fiber optics surface reflectometer were used to measure ignition delay time and reflected optical energy of several compositions of composite, double base and nitramine base rocket propellant at different pressure levels each other. The order of ignitability was double base > composite > Nitramine propellants at initial pressure of over 75 psia. The highest ignition energy was needed to ignite nitramine propellant, however, as the pressure increased up to the range of $75{\sim}400$ psia as the ignition delay time decreased abruptly. The absorbtion of radiation energy could be increased by the addition of small amount of opacifiers as carbon black, ZrC, WC and burning catalyst.

• Fire Science and Engineering
• /
• v.24 no.4
• /
• pp.92-97
• /
• 2010

Fire simulation by using a computational fluid dynamics model and examination of the fires at indoor shooting ranges broken out in the past were conducted, to presume causes of the fire at the indoor shooting range in Busan and suggest fire safety measures. On-site investigations and shooting tests on unburned gunpowder were also carried out. No trace of the muzzle spark and spark at the bullet trap was found in CCTV footage, and the impact of a stray bullet failed to ignite gunpowder. Cigarette was therefore presumed to be the most likely source of ignition among the potential sources. It appeared that the explosion in the shooting area was caused by violent burning of the polyurethane sound absorber and unburned gunpowder accumulated on it. The fire safety measures include prohibit of use of profile polyurethane sound absorber, removal of steel components from bullet trap, clean up and control of unburned gunpowder, etc.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.1
• /
• pp.49.1-49.1
• /
• 2013

We have been carrying out near-infrared (NIR) spectroscopy as well as [Fe II] narrow band imaging observations of Cassiopeia A supernova remnant (SNR). In this presentation, we describe the spectral classification of the iron knots around the SNR. From eight long-slit spectroscopic observations for the iron-bright shell, we identified a total of 61 iron knots making use of a clump-finding algorithm, and performed principal component analysis in an attempt to spectrally classify the iron knots. Three major components have emerged from the analysis; (1) Iron-rich, (2) Helium-rich, and (3) Sulfur-rich groups. The Helium-rich knots have low radial velocities (${\mid}v_r{\mid}$ < 100 km/s) and radiate strong He I and [Fe II] lines, that match well with Quasi-Stationary Flocculi (QSFs) of circumstellar medium, while the Sulfur-rich knots show strong lines of oxygen burning materials with large radial velocity up to +2000 km/s, which imply that they are supernova ejecta (i.e. Fast-Moving Knots). The Iron-rich knots have intermediate characteristics; large velocity with QSF-like spectra. We suggest that the Iron-rich knots are missing "pure" iron materials ejected from the inner most region of the progenitor and now encountering the reverse shock.

• Journal of Korean Society for Quality Management
• /
• v.47 no.3
• /
• pp.631-639
• /
• 2019

Purpose: In this paper we present a case study of applying quick and easy experimental design approach to develop a Halogen free flame retardant material for cellular phone charger cable. Methods: We employ sequential experimentation of mixture design, verification design, and factorial design. A quick and easy approach is adopted based on data investigation and graphical method instead of strict statistical analysis, which helped enhancing smooth communication with the engineers and speeding up the development process. Results: Flame retardant material in pellet type produced from the optimal condition is transported to the customer and tested, to pass the customer retardancy criteria. Conclusion: The quick and easy experimental design approach is considered to be useful in this case study.

• Nuclear Engineering and Technology
• /
• v.37 no.4
• /
• pp.317-326
• /
• 2005

The burning-out of excess plutonium from the reprocessing of spent nuclear fuel and from the dismantlement of nuclear weapons is recently emphasized due to the difficulties in securing the final repository for the spent fuel and the necessity to consume the ex-weapons plutonium. An irradiation test in the Halden reactor was launched by the OECD Halden Reactor Project (HRP) to investigate the in-pile behavior of plutonium-embedded fuel as a form of mixed oxide (MOX) and of inert matrix fuel (IMF). The first cycle of irradiation was successfully accomplished with good integrity of test fuel rods and without any undesirable fault of instrumentations. The test results revealed that the MOX fuel is more stable under irradiation environments than IMF. In addition, MOX fuel shows lower thermal resistance due to its better thermal conductivity than IMF. The on-line measured in-pile performance data of attrition milled MOX fuel are used in the analysis of the in-pile performance of the fuel with the fuel performance code, COSMOS. The COSMOS code has been developed for the analysis of MOX fuel as well as $UO_2$ fuel up to high burnup and showed good capability to analyze the in-reactor behavior of MOX fuel even with different instrumentation.

• Nuclear Engineering and Technology
• /
• v.53 no.8
• /
• pp.2454-2463
• /
• 2021

The objective of this research is to the use of americium (AmO₂) as a burnable absorber effectively instead of conventional gadolinium (Gd₂O₃) for VVER-1200 reactor by analyzing its impacts on reactivity, power peaking factor (PPF), safety factor, and quality of the spent fuel. The assembly is burned to 60 GWd/t by using SRAC-2006 code and JENDL-4.0 data library for finding the optimum amount and effective way of using AmO₂ as a burnable absorber. From these studies, it is found that AmO₂ can decrease the excess reactivity like Gd₂O₃ without changing the criticality life span and enrichment of ²³⁵U. A homogeneous mixture of the 0.20% AmO₂+ 4.95% enriched UO₂ fuel rod (model MF-4) decreases the PPF than the reference assembly. The use of AmO₂+UO₂ in the integral burnable absorber (IBA) rod or the outer layer could also decrease the PPF up to 10 GWd/t but increases rapidly after 30 GWd/t, which could be a safety threat. The fuel temperature coefficient and void coefficient of the model MF-4 are the same as the reference assembly. In addition, 22% of initially loaded Am are burning effectively and contributing to the power production.