• Earthquakes and Structures
• /
• 제2권1호
• /
• pp.1-24
• /
• 2011

During very strong earthquakes, seismically isolated buildings may experience large horizontal relative displacements, which may lead to poundings if an insufficiently wide clearance is provided around the building. This paper investigates, through numerical simulations, the effectiveness of using rubber bumpers, which could be attached at locations where it is likely to have impacts, in order to act as shock-absorbers. For the simulation of the dynamic behavior of such rubber bumpers during impacts, a nonlinear force-based impact model, which takes into account the finite thickness of the rubber bumpers, has been developed. Subsequently, a series of parametric analyses are performed to assess the effect of the gap size, the earthquake characteristics and the thickness, compressive capacity and damping of the bumpers. The stiffness of the moat wall is also parametrically considered during poundings of a seismically isolated building, as another potential mitigation measure for poundings of seismically isolated buildings.

• 한국농림기상학회:학술대회논문집
• /
• 한국농림기상학회 2019년도 하계 학술발표초록집
• /
• pp.130-143
• /
• 2019

• Earthquakes and Structures
• /
• 제23권2호
• /
• pp.129-138
• /
• 2022

One of the objectives to prevent building pounding between two adjacentstructures is to considerseparation distance or decrease relative displacement during seismic excitation. Although the majority of building codes around the world have basically suggested some equations or approximately recommended various distances between structuresto avoid pounding hazard, but a lot of reportsin zone of pounding have obviously shown thatsafety situation or economic consideration are not always provided due to the collisions between buildings and the cost of land, respectively. For this purpose, a dynamic MDOF model by having base isolation system is numerically considered and using various earthquake records, relative displacements are mathematically investigated. Different equations to determine the value of damping ratio are collected and the results of evaluations are listed for comparison among them to present a new equation for determination of impact damping ratio. Presented equation is depends significantly on impact velocity before and after impact based on artificial neural network, which the accuracy of them is investigated and also confirmed. In order to select the optimum equation, hysteresisloop of impact between base of building and rubber bumper is considered and compared with the hysteresis loop of each impact, calculated by different equations. Finally, using representative equation, the effect of thickness, number and stiffness of rubber bumpers are numerically investigated. The results of analysis indicate that stiffness and number of bumpers have significantly affected in zone of impact force while the thickness of bumpers have not shown significant influence to calculate impact force during earthquake. For instance, increasing the number of bumpers, gap size between structures and also the value of stiffness is caused to decrease impact force between models. The final evaluation demonstrates that bumpers are able to decrease peak lateral displacement of top story during impact.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1736-1740
• /
• 2003

There have been various studies to find out the correlation between subjective and objective evaluation ride comfort in vehicle. To be proper, subjective evaluation considers the signal pattern of vibration generated by vehicle. In this study, driving test is carried out to extract the correlation between subjective evaluation by subjects and vibration signals measured on the seat when a test vehicle is passing over test bumpers, which have two sorts of width change and height change respectively. A unique reference bumper is used to be compared with the relative comfort of test bumpers.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1992년도 춘계학술대회 논문집 92
• /
• pp.115-130
• /
• 1992

The analysis of thermoplastic automotive bumpers needs not only characterizations of the thermomechanical properties of thermoplastic materials but also the finite element method which can solve the problems with a large deflection, an elastic-inelastic deformation, and a change of a contact state. This paper describes the modeling techniques in the finite element analysis in order to get a good prediction of thermoplastic bumper behaviors. Simplification effects of a complex geometry of thermoplastic bumpers are studied by comparing the results from static loading tests and the finite element analysis.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2002년도 봄 학술발표회 논문집
• /
• pp.243-246
• /
• 2002

자동차 차체 제작을 위해서는 차체의 견고성과 승객의 안전성을 동시에 고려하여 너무 강하거나 너무 무르지 않은 재질의 선택과 차체 설계의 최적화가 요구된다. 본 논문에서는 차량 충돌 시 자동차의 안전도를 향상시키면서 차량의 손상을 최소화 함으로써 수리비를 절감하기 위한 목적으로 TPU(Thermoplastic Polyurethane Elastomer)에 공기를 채워서 만든 에어백 자동차 범퍼를 개발하였다. (중략)

• 한국자동차공학회논문집
• /
• 제18권1호
• /
• pp.99-104
• /
• 2010

It is a frequent occurrence in urban traffic - a low-speed collision in which one vehicle hits the back of another. The vehicles often sustain expensive damage. Bumpers can reduce this damage, but only line up so the initial contact in an impact is bumper to bumper. Then the bumpers on the colliding vehicles have to absorb the crash energy, keeping damage away from expensive sheet metal, lights, and other components. In real world accidents, Bumper mismatches in crashes are increasing, and the resulting repair costs from low-speed collisions are escalating. In this study, we investigated the bumper rail height and analyzed their effects on repair cost. Futhermore, Our 16kph front-into-rear crash tests demonstrates bumper mismatch problem.

• 자원리싸이클링
• /
• 제18권1호
• /
• pp.44-51
• /
• 2009

이 연구는 신개발 범퍼의 충격흡수성능 시험기준을 적용하여 재활용 범퍼의 충격흡수성능을 실험하고, 재활용 범퍼의 성능 특성을 비교한 것이다. 본 연구에서 적용된 범퍼는 유형이 다른 두 종류의 승용차 외장 범퍼를 선정하여 2종류의 재활용 범퍼를 자동차 안전 기준에 따라 충격흡수성능을 시험하였다. 재활용 범퍼의 충격 흡수성능 실험 결과 2.5마일 범퍼 충격 성능 특성은 동일한 차종의 신품 범퍼의 충격 성능 및 흡수 성능 특성과 거의 동등수준의 충격 성능 특성을 나타내었다.

• Plant Breeding and Biotechnology
• /
• 제6권4호
• /
• pp.381-390
• /
• 2018

Percentage of aerenchyma area has been closely linked with amounts of methane emitted by rice. A diversity panel of 39 global rice varieties were examined to determine genetic variation for root transverse section (RTS), aerenchyma area, and % aerenchyma. RTS and aerenchyma area showed a strong positive correlation while there existed no significant correlation between RTS area and % aerenchyma. Five varieties previously shown to differ in methane emissions under field conditions were found to encompass the variation found in the diversity panel for RTS and aerenchyma area. These five varieties were evaluated in a greenhouse study to determine the relationship of RTS, aerenchyma area, and % aerenchyma with methane emissions. Methane emissions at physiological maturity were the highest for 'Rondo', followed by 'Jupiter', while 'Sabine', 'Francis' and 'CLXL745' emitted the least. The same varietal rank, 'Rondo' being the largest and 'CLXL745' the smallest, was observed with RTS and aerenchyma areas. RTS and aerenchyma area were significantly correlated with methane emissions, r = 0.61 and r = 0.57, respectively (P < 0.001); however, there was no relationship with % aerenchyma. Our results demonstrated that varieties with a larger root area also developed a larger aerenchyma area, which serves as a gas conduit, and as a result, methane emissions were increased. This study suggests that root transverse section area could be used as a means of selecting germplasm with reduced $CH_4$ emissions.

• 자원리싸이클링
• /
• 제28권4호
• /
• pp.37-43
• /
• 2019

현재 우리나라의 차량 증가에 따른 폐차도 증가추세에 있어 이에 따른 각종 환경오염 문제로 인해 자원 재순환에 대한 관심이 고조되고 있는 실정이다. 본 연구에서는 국내 자동차 부품 재제조시장의 사업도입에 따른 경제적 효과를 정량적으로 평가하고자 자동차의 부품중 상대적으로 재제조율이 낮은 부품인 범퍼, 도어, 펜더에 대해서 비용편익을 분석하였다. 분석 결과 각각 비용 편익은 제품별 개당 54,000원으로 발생하는 것으로 나타났고, 신제품의 50%를 재제조할 경우 매립비용의 절감으로 개당 226,060원의 이익이 발생하는 것으로 나타났다. 이와 같이 범퍼, 도어, 펜더를 재제조 했을 경우 상당한 편익이 발생하여 재제조업체의 충분한 경제성 확보가 가능할 것으로 판단된다.