• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.1376-1379
• /
• 2006

Vibro crushed-stone compacted pile (VCCP) method is one of a ground improvement technique by a vibro compaction in vertical direction with crushed stone to build up stone pile foundation in other to ensure stability of soft ground. In spite of its long applied history in geotechnical engineering division, most of studies have not been based on the reliable In-situ condition but on the laboratory tests including model tests. These model tests can express standard and ideal behavior but exceptional status that can be occur in the ground cannot be considered efficiently. This study performed the the series of trial construction to investigate the effect of VCCP method on the improvement of soft ground expecially in railroad construction site.

• Tribology and Lubricants
• /
• v.25 no.1
• /
• pp.66-72
• /
• 2009

Al-based composites reinforced with SiC particulate were fabricated using a thermal spray process, and dry sliding wear behavior of the composites was investigated. Pre-mixed Al and SiC powders were sprayed on an A16061 substrate by flame spraying, and dry sliding wear test were performed under various sliding speed and applied load conditions against ${Al_2}{O_3}$ ball. Wear behavior of the composites was studied by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). And build-up mechanism of MML on the worn surface of the composites was examined. It was revealed that these MML was formed of debris from the contact surface of the composites and effected to wear behavior of the composites protecting the contact surface of the composites.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.270-279
• /
• 2003

Parametric studies have been conducted into the variability of the factors affecting the ultrasonic testing applied to weldments. The influence of ultrasonic equipment, transducer parameters, test technique, job parameters, defect type and characteristics on reliability far defect detection and sizing was investigated by experimentation. The investigation was able to build up substantial bank of information on the reliability of manual ultrasonic method for testing weldments. The major findings of the study separate into two parts, one dealing with correlation between ultrasonic techniques, equipment and defect parameters and inspection performance effectiveness and other with human factors. Defect detection abilities are dependent on the training, experience and proficiency of the UT operators, the equipment used, the effectiveness of procedures and techniques.

• Elastomers and Composites
• /
• v.54 no.1
• /
• pp.40-53
• /
• 2019

The physical properties of chloroprene rubber (CR) compounds reinforced with networked silicas were investigated by comparing them to those reinforced with conventional silica to observe the effect of the organic connection bonds combining silica particles on their cure, tensile, and aging performance. The introduction of networked silica to CR increase in silica content to 80 phr in rubber, while the content of conventional silica was limited to 60 phr. The CR compounds reinforced with networked silica showed higher resistance to combustion. The gradual increases in delta torque, Mooney viscosity, and modulus of silica-filled CR compounds with silica content were mainly attributed to the specific interaction between the chlorine atoms of CR and the hydroxyl groups of silica. The CR compounds reinforced with networked silica showed low compression set and heat build-up and maintained their high modulus even after thermal, oil, and ozone aging.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.53-54
• /
• 2022

There is an increasing demand for prediction of asbestos concentration which has an fatal effect on human body. While demolishing asbestos, the dust scatters and makes workers be exposed to danger. Up to this date, however, factors that particularly influences have not considered in predicting asbestos concentration. Most of the studies could not quantify the distribution of asbestos. Also, they did not use nominal data on buildings as important factors. Therefore, this study aims to build an asbestos concentration prediction model by quantifying distribution of asbestos and using nominal data of buildings based on Artificial Neural Network (ANN). This model can give significant contribution of improving the safety of workers and be useful for finding effective ways to demolish asbestos in planning.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.1
• /
• pp.3-12
• /
• 1984

Up to now, it has been common to treat the maneuvering motion of a ship as a 3-degree-freedom motion i.e. surge, sway and yaw on the sea surface, for the simplicity and mathematical calculation, and it is quite acceptable in the practical point of view. Meanwhile, considering the maneuverability of a ship under the special conditions such as in irregular waves, in wind or at high speed with small GM value, it is required that roll effect must be considered in the equation of ship motion. In this paper the author tried to build up the 4-degree-freedom motion equation by adding roll. And then, applying the M.M.G.'s mathematical model and with captive model test results the roll-coupled hydrodynamic derivatives were found. With these the author could make some simulating program for turning and zig-zag steering. Through the computer simulations, the effect of roll to the ship maneuver became clear. The effect of the wind force to the maneuverability was also found. Followings are such items that was found. 1) When roll is coupled in the maneuvering motion, the directional stability becomes worse and the turning diameter becomes smaller as roll becomes smaller as roll becomes larger. 2) When maneuver a ship in the wind, the roll becomes severe and the directional stability becomes worse. 3) When a ship turns to the starboard side, the wind blowing from 90 degree direction to starboard causes the largest roll and the largest turning diameter, and the wind from other direction doesn't change the turning diameter. 4) When a ship is travelling with a constant speed with rudder amidship, if steady wind blows from one direction, the ship turns toward that wind. This phenomenon is observed in the actual seaways.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.15 no.4
• /
• pp.109-120
• /
• 2020

This study examines how the government's fairness in entrepreneurship support affects satisfaction and management performance, and examines whether these influences are different for each growth stage of start-up companies. For this study, data were collected for start-up companies that received government support for start-up within the past 5 years. Total 611 copies of the data were used in this study. The collected data were analyzed using SPSS and AMOS. The fairness used in this study was divided into three types, procedural fairness, interactive fairness, and distributed fairness. The effect of the three fairness on the satisfaction of start-up support project was analyzed. In addition, the effect of business support satisfaction on business performance was analyzed, where the business performance was evaluated by the questioner's satisfaction with their business. The start-up phase was divided into the start phase, early growth phase, stagnant phase, and high-level growth phase, and the moderating effect between the fairness and satisfaction of the government-supported projects by start-up phase was analyzed. As a result, it was found that every concept of fairness had a positive (+) effect on the satisfaction of the entrepreneurship support project, and the satisfaction of the entrepreneurship support project had a positive (+) effect on the management performance. The concept of procedural fairness in the start phase, procedural fairness in the early growth phase, interactive fairness, and the concept of all fairness in the stagnant phase influenced the satisfaction of the start-up support project. In this study, the fairness and effect of government-supported projects affecting the management performance of start-ups were identified by growth phase of start-ups. The results of these studies will help build a systematic system for entrepreneurship support and for start-ups, it will also greatly contribute to finding differentiated growth plans by growth stages of start-up companies.

• Journal of Global Scholars of Marketing Science
• /
• v.8
• /
• pp.233-267
• /
• 2001

The management environment in Korea today is undergoing rapid changes; in particular, domestic corporations and businesses are confronting formidable adversity with IMF crisis and WTO. Though cost cutback, higher quality, rapid production, and diversification of products were accepted as important requirements for competitiveness in the past, they have been replaced by brand power. Consumption patterns have changed their focus from function to image orientation. This is why managers in corporations have invested enormous amounts of resources into producing powerful brands, which can attract consumers' attention greatly enough to improve the image of their products. Brands are regarded as a vital vehicle for marketing strategies and thus as a legal asset. Brands with remarkable and favorable image can secure a loyal consumer groups stable revenues. M & A, currently active between corporations, makes brand equity all the more important. The purpose of the present study was to investigate the effect of internal marketing and increased brand diversification on brand equity by combining them as influential factors with marketing mix factor. For this purpose, literature review was make on previous fragmented studies of influential factors on brand equity build-up. Based on the findings of this study, some operational implications were suggested for marketing managers. The findings and implications of the present study are as follows; First, efficient communication among organization members was found to have a significant effect on product quality. Second, job satisfaction and efficient communication among members was shown to significantly influence price policies. Thirdly, efficient communication among organization workers proved to have a significant effect on distribution strategies. Forth, efficient communication among members was demonstrated to significantly influence advertisement and other public-relations activities. Fifth, opacity of market environment appeared to have a significant effect on product quality, prior market entrance as perceived by organization members turned to be of negative influence on product quality. Sixth, opacity of market environment was found to have a significant effect on price policies. Seventh, opacity of market environment was shown to be of significant effect on distribution strategies. Eighth, grater opacity of market environment proved to improve advertisement and other public-relations activities. Ninth, price policies, distribution strategies, advertisement and public-relations activities were found to have a significant effect on brand equity value. To sum up these findings, in order for corporations and businesses to cope with consumers' needs that are increasingly segmented, internal marketing strategies and brand diversification should be implemented so as to generate greater synergy effect. It is also important to stress that differentiated, higher competitiveness should be secured for Korean corporations and businesses to survive in the drastically changing, globalized market environment. In this regard, continuous and long-term management strategies for brand equity build-up should be ensured and is essential in the present unlimited competition. The last but not least important point to notice is that to increase brand equity value, intensive investment and constant emphasis should be made on internal marketing management on intra-organizational members before strengthening external marketing.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.6
• /
• pp.800-808
• /
• 1999

To compare several porcelains made by various manufacturers in shrinkage after firing and investigate the effect of condensation on shrinkage, specimens were prepared and the volume of each body was measured by the phase-shifting profilometry. Baseplate wax was cut by $2.5cm{\times}2cm$ and cast in nonprecious metal(Verabond, U.S.A.), then any surfaces of specimens were abrased and polished on the SiC abrasing papers, preparing 120 specimens. Specimens were divided into six groups according to the porcelain used, and the porcelain used in each group were as follows. Group I : Ceramco dentin porcelain Group B : Creation dentin porcelain Group III : Creation margin porcelain Group IV : Vintage margin porcelain Group V : Vita dentin porcelain Group VI : Vintage dentin porcelain Porcelain was built up on the metal plates using a small spoon and then solution matching to each porcelain was added. The six groups are subdivided into a and b. In subgroup a, only excessive solution was absorbed with tissue and in subgroup b, porcelain was condensed sufficiently. When build-up was completed, the shape was measured using the phase-shifting profilometry. After that, specimens were fired in the furnace programed for each porcelain and then their changed shape were measured again. Using the difference between the two above measurements, the ratio of shrinkage was calculated. Obtained results were as follows ; 1. Regardless of condensation, the volume of fired specimens were not different significantly between the two subgroups a and b in the same group. 2. The ratios of shrinkage were significantly higher in the groups porcelain built-up was condensed than in the groups not condensed 3. The ratios of shrinkage were in the range of 36.81-27.19% in the groups porcelain built up was condensed and 44.52-37.54% in the other groups not condensed.

• Korean Journal of Child Studies
• /
• v.38 no.2
• /
• pp.177-190
• /
• 2017

Objective: The purpose of this study was to verify the effectiveness of a group counseling program with phototherapy for enhancing the self-perception and self-esteem of female adolescents. Methods: The participants of this study were 40 female middle school students with 20 in the experimental group and 20 in the control group. We conducted an 8-week program with a 4-week follow-up session for the participants. Collected data were analyzed with t-tests, ANCOVA, and ANOVA with PASW Statistics 18.0 (SPSS Inc., Chicago, IL). Results: The findings showed that the self-perception and self-esteem of the experimental group increased after the program whereas the control group showed no difference. In addition, the phototherapy group counseling program showed that the treatment effect was maintained even after 4 weeks. Conclusion: The group phototherapy program helped the female middle school students' to build a more positive self-concept, with respect to both self-perception and self-esteem.