• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.5
• /
• pp.212-221
• /
• 2010

The bubbles could be created from multiple source in the surface of ocean. The bubbles which are created like this affect to the intensity and the sound speed of acoustic wave which are used from the ocean. From the research, it observed Reverberation from the sea surface, using Vbeam transmission and reception equipment that was a cross-shaped Array, from 2008 July 2nd to July 3rd at 4Km from the East Sea Mookho port. It is difficult to analyze data because the received signal has ambient noise and occurrence ISI(Inter Symbol Interference) for multipath. This paper remove that ambient noise and ISI using the directions of arrival beamforming and the filter and sum beamforming. After beamforming, a following DFE(Decision Feedback Equalizer) removes the remaining multipath components. Experimental results show that the proposed technique reduce the errors caused by ISI.

• Journal of Korea Foundry Society
• /
• v.37 no.3
• /
• pp.71-77
• /
• 2017

Casting defects produced during the casting process seriously affect the mechanical properties of the resulting products, reduce the performance capabilities of the product, and also result in economic losses. Therefore, this paper mainly investigates the causes of defects and methods by which to reduce these defects stemming from molten metal flows in a runner system of the type widely used in the sand mold casting process. The flow characteristics of a molten alloy are difficult to observe during the actual casting process. For this reason, a water model was used to observe the flow in the casting process, and the flow in each case was recorded using high-speed cameras as part of the experimental process of this study. Several repetitive experiments were performed to improve the accuracy of the experimental results. The traditional casting system was modified according to the design rules proposed by Campbell, and the system was termed flow-adaptive gating system with a water model. Comparing the flow characteristics of traditional and adaptive gating systems with a water model shows that the bubbles in the water in the latter case are reduced more significantly than in the former case. A ceramic filter system was adapted to the flow-adaptive gating system to minimize the instability of the flow during filling, which occurs as the fluid velocity in the runner increases. In additional, the flow behavior with and without the filter system were compared. The water model system in this work was shown to be able to verify that the adaptation of the filter system brings improvements by stabilizing the flow and reducing the amount of bubbles in the runner system. Moreover, using the flow-adaptive runner system with the filter system leads to considerably stable flows in the runner system.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.8
• /
• pp.562-569
• /
• 2004

An experiment for observation of the distribution of the seagrass (zostera marina) beds and characteristics of high-frequency backscattering by the photosynthesis was conducted off the coast. Acoustic data were taken as a function of the grazing angles and the relative azimuth angles on the seagrass beds of which bottom type was sandy-mud. The transmitted source signal was a 120 kHz CW waveform. Mapping of the seagrass beds distribution was drawn up using the seagrass backscattering strength with azimuth and grazing angles. The result of the comparison backscattering strength distribution of the seagrass beds was shown to be the similar to the photograph of real seagrass beds. The seagrass backscattering strength was also compared between day and night to verify the effects of the acoustical scattering by the bubbles of Photosynthetic oxygen formed on the seagrass. In these results. it is clear that observation of the seagrass beds between day and night showed the different characteristics because the bubbles of Photosynthetic oxygen affect the acoustical scattering.

• Smart Structures and Systems
• /
• v.13 no.4
• /
• pp.615-636
• /
• 2014

Aluminium Foam Sandwich (AFS) panels are becoming always more attractive in transportation applications thanks to the excellent combination of mechanical properties, high strength and stiffness, with functional ones, thermo-acoustic isolation and vibration damping. These properties strongly depend on the density of the foam, the morphology of the pores, the type (open or closed cells) and the size of the gas bubbles enclosed in the solid material. In this paper, the vibrational performances of two classes of sandwich panels with an Alulight(R) foam core are studied. Experimental tests, in terms of frequency response function and modal analysis, are performed in order to investigate the effect of different percentage of porosity in the foam, as well as the effect of the random distribution of the gas bubbles. Experimental results are used as a reference for developing numerical models using finite element approach. Firstly, a sensitivity analysis is performed in order to obtain a limit-but-bounded dynamic response, modelling the foam core as a homogeneous one. The experimental-numerical correlation is evaluated in terms of natural frequencies and mode shapes. Afterwards, an update of the previous numerical model is presented, in which the core is not longer modelled as homogeneous. Mass and stiffness are randomly distributed in the core volume, exploring the space of the eigenvectors.

• Composites Research
• /
• v.28 no.2
• /
• pp.70-74
• /
• 2015

In this paper, carbon nanotubes (CNTs) and micro glass bubbles (GBs) have been incorporated into a polyamide6 (PA6) matrix to impart thermoelectric properties. The spaces created in the matrix by GBs allows the formation of "segregated" CNT network. The tightly bound CNT network, if controlled properly, can serve as a conductive path for electron transport, while prohibiting phonon transport, which would provide an ideal configuration for thermoelectric applications. The CNTs and GBs were dispersed in a nylon-formic acid solution using horn sonication followed by coagulation in deionized water, and nanocomposite panels were fabricated using a hot press. The performance of nanocomposite panels was evaluated from thermal and electrical conductivities and Seebeck coefficient, and a thermoelectric figure of merit as high as 0.016 was achieved.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.12 no.1
• /
• pp.74-77
• /
• 2008

The radiopharmaceuticals are routinely injected to blood vessel for acquiring PET image. For this reason, It is imperative that they undergo strict quality control measures. Especially, Sterility test is more important than any other quality control procedures. According to the FDA guideline, It requires filter integrity test used in the processing of sterile solutions. Among several methods, we can decide to use bubble point test. We usually use vented GS-filters (Millipore co., USA) which are sterilizinggrade (0.22 um pore size) and are placed upper site on product vial. After the synthesis of $^{18}F$-FDG, solutions wet the membrane in filter and then go into the product vial. By all synthesis steps have finished, we can observe the presence of the bubbles in the product vial. Since we have started this study, we have never found any bubbles in the product vial. Because the maximum pressure intensity of the filter which has set by manufacturer is up to 5 bars, but helium gas pressure is up to 1 bar in our module system. So, we can make 5 bars pressure using helium gas bombe and increase pressure up to 5 bars step by step. However, it does not happen to anything in vial.

• Journal of Korean Society of Water and Wastewater
• /
• v.27 no.2
• /
• pp.261-272
• /
• 2013

Algae boom (Red tide) in south coastal area of Korea has been appeared several times during a decade. If algae boom appears in the desalination plant, media filter and UF filter are clogged quickly, and the plant should be shutdown. In general, Algae can be removed from water by flotation better than by sedimentation, because of the low density of algal cell. The purpose of this study conducts the CFD simulation of DAF flotation basin to apply the design of the dissolved air flotation with ball filter in the Test Bed for SWRO desalination plant. In this study, Eulerian-Eulerian multiphase model was applied to simulate the behavior of air bubbles and seawater. Density difference model and gravity were used. But de-sludge process and mass transfer between air bubbles and seawater were ignored. Main parameter is hydraulic loading rate which is varied from 20 m/hr to 27.5 m/hr. Geometry of flotation basin were changed to improve the DAF performance. According to the result of this study, the increase of hydraulic loading rate causes that the flow in the separation basin is widely affected and the concentration of air is increased. The flow pattern in the contact zone of flotation basin is greatly affected by the location of nozzle header. When the nozzle header was installed not the bottom of the contact zone but the above, the opportunity of contact between influent and recycle flow was increased.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.5
• /
• pp.209-217
• /
• 2011

In recent days, while taller and more massive structures such as huge bridges and super skyscrapers have been welcomed, the structural stabilization in design and construction have been gradually limited due to the major weakness of current concrete which is relatively heavier when compared with its strength. To improve the weakness of the current concrete, The lightweight concrete with light weight and high strength should be used; however, not many researchers in Korea have studied on the lightweight concrete. Generally, artificial lightweight aggregate produced through high-temperature-plasticization has a possibility of its body-expansion with many bubbles. Therefore, depending on the size of aggregate, the effects of bubbles on the specific weight and strength of the lightweight concrete should be studied. In this study, considering grain-size, the mix design of the artificial lightweight aggregate produced through the high-temperature-plasticization and the body-expansion of waste and clay from the fire power plant in Korea was conducted. The experiment to analyze the variation in specific weight and strength of the lightweight concrete was followed. From these experiments, the optimized grain-size ratio of the artificial lightweight aggregate for the enhancement of high-strength from the lightweight concrete was revealed.

• Nuclear Engineering and Technology
• /
• v.46 no.2
• /
• pp.147-158
• /
• 2014

In order to investigate how the microstructure of fuel/matrix-interaction (FMI) layers change during irradiation, different U-7Mo dispersion fuel plates have been irradiated to high fission density and then characterized using scanning electron microscopy (SEM). Specifially, samples from irradiated U-7Mo dispersion fuel elements with pure Al, Al-2Si and AA4043 (~4.5 wt.%Si) matrices were SEM characterized using polished samples and samples that were prepared with a focused ion beam (FIB). Features not observable for the polished samples could be captured in SEM images taken of the FIB samples. For the Al matrix sample, a relatively large FMI layer develops, with enrichment of Xe at the FMI layer/Al matrix interface and evidence of debonding. Overall, a significant penetration of Si from the FMI layer into the U-7Mo fuel was observed for samples with Si in the Al matrix, which resulted in a change of the size (larger) and shape (round) of the fission gas bubbles. Additionally, solid fission product phases were observed to nucleate and grow within these bubbles. These changes in the localized regions of the microstructure of the U-7Mo may contribute to changes observed in the macroscopic swelling of fuel plates with Al-Si matrices.

• Korean Journal of Veterinary Pathology
• /
• v.2 no.1
• /
• pp.53-60
• /
• 1998

A fourteen-month-old Holstein bull from a private cattle fattening farm at Ansung county in Kyunggi Province Korea was submitted on August 2nd 1997, for examination at the Pathology Division of the National Veterinary Research Institute. The bull died within 24 hours after developing clinical signs of abrupt inertia, complete anorexia high fever(40.3℃) diffuse severe emphysematous swelling of upper part of the right hind leg lateral recumbancy and paralysis. At necropsy diffuse severe subcutaneous redness and influx of serosanguinous exudate containing gas bubbles had accumulated under the thorax right hip and upper region of right hind leg. Muscles in upper right hind leg were blackish to dark red and yellowish brown in color. Muscle bundles were dry and separated by gas bubbles and serosanguinous fluids and muscles sections from affected regions floated in water. Histopathologically muscle fibers were partially or entirely degenerated fragmented and separated by exudate and gaseous substance mixed with polymorphonuclear cells. Blood vascular walls in affected regions showed severe acute fibrinoid necrosis. Typical large rod-shaped bacteria with or without oval central to subterminal spores were frequently observed in tissue sections stained with H-E and Gram stain. The large Gram-positive anaerobic endospore-producing rods were isolated from the suspension of muscle lesions. Isolated bacteria were identified as Clostridium(CL) chauvoei and CL. sordellii by biochemical tests. This case was diagnosed as blackleg based on the typical clinical signs gross finding histopathological observation and bacteriological results. This is the first case report on blackleg associated with Cl. chauvoei and Cl. sordellii in Holstein cattle in Korea.