• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.2
• /
• pp.386-391
• /
• 2006

In this paper, a design of V-type Linearly Tapered Slot Antenna(V-LTSA) with uniplanar microstrip-to-coplanar stripline(CPS) transitions is presented. The effect of reducing and increasing with taper width G, teper length L and opening angle are also considered at 5.8 GHz. In the result of a simulation by using CST-MWS, the return loss characteristic came very wide band about 4.3GHz, or 1.8 Octave. Proposed V-LTSA design schemes are expected to be a good antenna for microwave and millimeter-wave communcations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.714-720
• /
• 2009

In this paper, design and the implementation method of a band-tunable ultra-wideband planar doubler are described Microstrip-to-CPS(balun) transition and Microstrip-to-CPW transition are respectively used for input/output matching circuits for the doubler. The Input balun structure allows to apply diode bias, and the doubler output frequency is tunable by changing the diode bias voltage. With the bias voltage of -0.6 V, the measured operating frequency band of the implemented doubler is $10{\sim}20$ GHz, with the bias voltage of $-0.2{\sim}-0.4$ V, the operating frequency band is $10{\sim}30$ GHz, and with 0 V bias, the operating frequency band is $20{\sim}30$ GHz. The doubler provides conversion loss of less than 15 dB and fundamental frequency suppression of 30 dB.

• Economic and Environmental Geology
• /
• v.31 no.1
• /
• pp.21-29
• /
• 1998

Broadband receiver functions are developed from teleseismic P waveforms recorded at Wonju (KSRS), Inchon (IRIS), and Pohang (PHN), and are analyzed to examine the crustal structure beneath the three stations. The teleseismic receiver functions are inverted in the time domain to the vertical P wave velocity structure beneath the stations. Clear P-to-S converted phases from the Moho interface are observed in teleseismic seismograms recorded at the three stations. We estimated the crustal velocity structures beneath the stations using the receiver function inversion. The general features of inversion results are as follows: (1) For Pohang station, there is a high velocity gradient at a 4~5 km deep for SE and NW back azimuth and a low velocity zone at around 10 km deep. The Moho depth is 28 km for NW direction. (2) The shallow crustal structure beneath Wonju station is somewhat complex and there is a high-velocity zone ($V_p{\simeq}6.8km/sec$) at 3 to 4 km deep. The average crustal thickness is 33 km, and a transition zone exists at a 30~33 km deep of lower crust, of which velocity is abruptly changed 6.4 to 7.9 km/sec. (3) For Inchon station, the crustal velocity gradient monotonously increases up to the Moho discontinuity and the velocity is abruptly changed from 6.2 km/sec to 7.9 km/sec at 29 km deep.

• The Journal of the Korea Contents Association
• /
• v.11 no.12
• /
• pp.28-39
• /
• 2011

While the broadband multimedia technologies have been developing, the commercial market of digital contents has also been widely spreading. Most of all, digital cartoon market like internet cartoon has been rapidly large so video cartooning continuously has been researched because of lack and variety of cartoon. Until now, video cartooning system has been focused in non-photorealistic rendering and word balloon. But the meaningful frame extraction must take priority for cartooning system when applying in service. In this paper, we propose new automatic frame extraction method for video cartooning system. At frist, we separate video and audio from movie and extract features parameter like MFCC and ZCR from audio data. Audio signal is classified to speech, music and speech+music comparing with already trained audio data using GMM distributor. So we can set speech area. In the video case, we extract frame using general scene change detection method like histogram method and extract meaningful frames in the cartoon using face detection among the already extracted frames. After that, first of all existent face within speech area image transition frame extract automatically. Suitable frame about movie cartooning automatically extract that extraction image transition frame at continuable period of time domain.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1470-1481
• /
• 2008

A demand for spectrum resources, especially in the low frequency bands, is ever increasing with the development of mobile telecommunications and so is their economic value as other national resources. Also, development in mobile broadband require more bandwidth with excellent propagation characteristics, such as those frequencies in the 700/800/900 MHz bands. As a way to enhance the economic efficiency of using spectrum resources, many countries including the U.S., the U.K. and Japan, have recently focused on the refarming plan of the low frequency bands according to the transition from analogue to digital TV. By the way, as a result of WRC-07, those parts of the band $698{\sim}960\;MHz$ in Region 2 and the band $790{\sim}960\;MHz$ in Regions 1 and 3 which are allocated to the mobile service on a primary basis are identified for use by administrations wishing to implement International Mobile Telecommunications (IMT). Therefore, after analogue to digital television switchover, some administrations may decide to use all or parts of the band $698{\sim}806/862\;MHz$ for other services to which the band is allocated on a primary basis, in particular the mobile service for the implementation of IMT, while in other countries the broadcasting service will continue to operate in that band. And to conclude, bands already identified for IMT-2000 will also be able to be used for IMT. This work will help establish a policy direction for spectrum refarming in the low frequency bands in Korea(Rep. of).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.1
• /
• pp.27-32
• /
• 2008

Novel long persistent phosphors of $CaZrO_3:Er^{3+}$ have been synthesized by traditional solid state reaction method. The long persistent phosphor crystalline particles were characterized by the X-ray diffraction (XRD), photoluminescence spectrophotometer, thermoluminescence (TL) and luminance meter. The results reveal that the samples are composed of single $CaZrO_3$ phase. The broadband emission spectra of 446 nm peak and 550 nm peak was revealed by synthesized at high temperature in $N_2$ gas. Green long persistent phosphors have been observed in the sys_em for over 6 h after UV irradiation (254 nm). The main emission peak was ascribed to $Er^{3+}$ ions transition from $^5D_{5/2}{\rightarrow}^4F_{9/2},\;^2H_{12/2},\;^4S_{3/2}{\rightarrow}^4I_{13/2}\;and\;^2G_{9/2}{\rightarrow}^4I_{13/2}$, and the afterglow may be ascribed to the suitable trap centers in the $CaZrO_3$ host lattice.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.109-109
• /
• 2010

$Er^{3+}$ ion shows a stable and efficient luminescence at 1.54mm due to its $^4I_{13/2}\;{\rightarrow}\;^4I_{15/2}$ intra-4f transition. As this corresponds to the low-loss window of silica-based optical fibers, Er-based light sources have become a mainstay of the long-distance telecom. In most telecom applications, $Er^{3+}$ ions are excited via resonant optical pumping. However, if nanocluster-Si (nc-Si) are co-doped with $Er^{3+}$, $Er^{3+}$ can be excited via energy transfer from excited electrical carriers in the nc-Si as well. This combines the broad, strong absorption band of nc-Si with narrow, stable emission spectra of $Er^{3+}$ to allow top-pumping with off-resonant, low-cost broadband light sources as well as electrical pumping. A widely used method to achieve nc-Si sensitization of $Er^{3+}$ is high-temperature annealing of Er-doped, non-stoichiometric amorphous thin film with excess Si (e.g.,silicon-rich silicon oxide(SRSO)) to precipitate nc-Si and optically activate $Er^{3+}$ at the same time. Unfortunately, such precipitation and growth of nc-Si into Er-doped oxide matrix can lead to $Er^{3+}$ clustering away from nc-Si at anneal temperatures much lower than ${\sim}1000^{\circ}C$ that is necessary for full optical activation of $Er^{3+}$ in $SiO_2$. Recently, silicon-rich silicon nitride (SRSN) was reported to be a promising alternative to SRSO that can overcome this problem of Er clustering. But as nc-Si formation and optical activation $Er^{3+}$ remain linked in Er-doped SRSN, it is not clear which mechanism is responsible for the observed improvement. In this paper, we report on investigating the effect of separating the nc-Si formation and $Er^{3+}$ activation by using hetero-multilayers that consist of nm-thin SRSO or SRSN sensitizing layers with Er-doped $SiO_2$ or $Si_3N_4$ luminescing layers.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.1 no.1 s.1
• /
• pp.139-155
• /
• 2001

We investigate the vertical velocity models beneath the newly installed broadband seismic network of KMA (Korea Meteorological Administration) by using receiver function inversion technique. The seismic phases are primarily P-to-S conversions and reverberations generated at the two highest impedance interfaces like the Moho (crust-mantle boundary) and the sediment-basement contact. We obtained the teleseismic P-wave receiver functions, which were derived from teleseismic records of Seoul (SEO), Inchon (INCN), Tejeon (TEJ) , Sosan (SOS/SES), Kangnung (KAN), Ulchin (ULC/ULJ), Taegu (TAG), Pusan (PUS), and Ullung-do (ULL) stations. For Kwangju (KWA/KWJ) and Chunchon (CHU) stations, the Moho conversion Ps arrivals and waveforms of radial receiver functions are azimuthally inconsistent and unclear. From the receiver function inversion result, we found that crustal thickness is 29 km at INCN, SEO, and SOS (SES) stations, 28 km at KAN station in the Kyonggi Massif, 32 km at TEJ station in Okchon Folded Belt, 34 km at TAG, 33 km at PUS station in the Kyongsang Basin, 32 km at KWJ station (readjusted station by prior KWA station) included in the Youngdong-Kwangju Depression Zone, 28 km at ULC station in the eastern margin of the Ryongnam Massif, and 17 km at ULL station in the Ullung Island of the East Sea, respectively. The Moho configuration of INCN, SOS, KWJ, and KAN stations show a laminated smooth transition zone with a 3-5 km thick. The upper crusts(${\sim}5km$) of KAN, ULC, and PUS stations show complex structures with a high velocity. The unusually thick crusts are found at the TAG and PUS stations in the Kyongsang Basin compared to the thin (29-32 km) crust of the western part (INCN, SEO, SOS, TEJ, and KWA stations) The crustal thickness beneath Ullung Island (ULL station) shows the suboceanic crust with about 17 km thickness and complex with a high velocity layer of the upper crust, and the amplitudes of Incoming Ps waves from the western direction are relatively large compared to those from othor directions.

• Korean Journal of Materials Research
• /
• v.21 no.5
• /
• pp.250-254
• /
• 2011

We have synthesized bluish-green, highly-efficient $BaSi_2O_2N_2:Eu^{2+}$ and $(Ba,Sr)Si_2O_2N_2:Eu^{2+}$ phosphors through a conventional solid state reaction method using metal carbonate, $Si_3N_4$, and $Eu_2O_3$ as raw materials. The X-ray diffraction (XRD) pattern of these phosphors revealed that a $BaSi_2O_2N_2$ single phase was obtained. The excitation and emission spectra showed typical broadband excitation and emission resulting from the 5d to 4f transition of $Eu^{2+}$. These phosphors absorb blue light at around 450 nm and emit bluish-green luminescence, with a peak wavelength at around 495 nm. From the results of an experiment involving Eu concentration quenching, the relative PL intensity was reduced dramatically for Eu = 0.033. A small substitution of Sr in place of Ba increased the relative emission intensity of the phosphor. We prepared several white LEDs through a combination of $BaSi_2O_2N_2:Eu^{2+}$, YAG:$Ce^{3+}$, and silicone resin with a blue InGaN-based LED. In the case of only the YAG:$Ce^{3+}$-converted LED, the color rendering index was 73.4 and the efficiency was 127 lm/W. In contrast, in the YAG:$Ce^{3+}$ and $BaSi_2O_2N_2:Eu^{2+}$-converted LED, two distinct emission bands from InGaN (450 nm) and the two phosphors (475-750 nm) are observed, and combine to give a spectrum that appears white to the naked eye. The range of the color rendering index and the efficiency were 79.7-81.2 and 117-128 lm/W, respectively. The increased values of the color rendering index indicate that the two phosphor-converted LEDs have improved bluish-green emission compared to the YAG:Ce-converted LED. As such, the $BaSi_2O_2N_2:Eu^{2+}$ phosphor is applicable to white high-rendered LEDs for solid state lighting.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1050-1058
• /
• 2005

This paper presents how to design and implement a very compact, cost effective and broad band receiver module for IEEE 802.16 FWA(Fixed Wireless Access) in the 40 GHz band. The presented receiver module is fabricated in a multi-layer LTCC(Low Temperature Cofired Ceramic) technology with cavity process to achieve excellent electrical performances. The receiver consists of two MMICs, low noise amplifier and sub-harmonic mixer, an embedded image rejection filter and an IF amplifier. CB-CPW, stripline, several bond wires and various transitions to connect each element are optimally designed to keep transmission loss low and module compact in size. The LTCC is composed of 6 layers of Dupont DP-943 with relative permittivity of 7.1. The thickness of each layer is 100 um. The implemented module is $20{\times}7.5{\times}1.5\;mm^3$ in size and shows an overall noise figure of 4.8 dB, an overall down conversion gain of 19.83 dB, input P1 dB of -22.8 dBm and image rejection value of 36.6 dBc. Furthermore, experimental results demonstrate that the receiver module is suitable for detection of Digital TV signal transmitted after up-conversion of $560\~590\;MHz$ band to 40 GHz.