• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1994.04a
• /
• pp.163-170
• /
• 1994

The widening of bridges under traffic condition brings to many problems. One of these is the internal stresses caused by different creep and shrinkage behavior of the existing bridge and that of the widened Bridge. This study was conducted to examine the effects of different creep and shrinkage behaviors between concretes. The results are as follows; Comparing the computational analysis results with the experimental study, it is shown that finite element analysis used in this study was well accorded with experimental results. And considering the shrinkage effects in widened bridges, joining-construction using the expanding concrete between the existing and widened bridge after at least three months from the day of completion of new bridge, is recommended.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.693-696
• /
• 1999

Reinforced concrete is, in general, known as high durability construction material under normal environments due to strong alkalinity of cement. It is , however, well known that moderate or minor cracks in reinforced concrete should be most serious causes to deteriorate the durability of RC structures. Furthermore, chloride contents penetrating through unexpected cracks in reinforced concrete bridges get to weaken corrosion resistance of reinforcement steel in concrete and than to accelerate the deterioration of concrete durability. The objective of this experimental research is 1) to evaluate the effect of various corrosion protection system for reinforced concrete specimens with moderate or minor cracks which are exposed to cyclic wet and dry seawater, and then 2) to develop effective corrosion protection system for reinforced concrete bridges under the exposure of various detrimental environments such as seawater, deicing and etc.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.101-104
• /
• 2002

Almost all buildings/infrastructures made of composite materials are fabricated without proper design. Unlike airplane or automobile parts, prototype test is impossible. One cannot destroy 10 story buildings or 100-meter long bridges. People try to build 100-story buildings or several thousand meter long bridges. In order to realize "composites in construction", the following subjects must be studied in detail, for his design. Concept optimization, Simple method of analysis, Folded plate theory, Size effects in failure, and Critical frequency. Unlike the design procedure with conventional materials, his design should include material design, selection of manufacturing methods, and quality control methods, in addition to the fabrication method. In this paper size/scale effects in failure criteria is briefly explained for practicing engineers.engineers.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.211-214
• /
• 2002

Almost all buildings/infrastructures made of composite materials are fabricated without proper design. Unlike airplane or automobile parts, prototype test is impossible. One cannot destroy 10 story buildings or 100-meter long bridges. People try to build 100-story buildings or several thousand meter long bridges. In order to realize "composites in construction", the following subjects must be studied in detail, for his design. Concept optimization, Simple method of analysis, Folded plate theory, Size effects in failure, and Critical frequency. Unlike the design procedure with conventional materials, his design should include material design, selection of manufacturing methods, and quality control methods, in addition to the fabrication method. In this paper, concept optimization and folded plate theory are presented for practicing engineers.engineers.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.4
• /
• pp.205-212
• /
• 2005

This paper presents the application of system identification approaches for the load carrying capacity evaluation of composite PCI girder bridges based on the result of field test. For these problems, the moment of inertia of cross-sectional area and the natural frequency of bridge were used as structural parameters, the SAP2000 program for the structural analysis and the SLP method for the minimum error. As a result, it is found that the proposed algorithm for this study appears applicable to real structures with reasonable complexity. It is shown that the introduction of approximate quadratic equations is more realistic and timesaving than the common methods.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.9 no.2
• /
• pp.31-37
• /
• 2003

In these days, several bridges have been built or under construction over navigational channel in Korea. In these cases there must be careful consideration for the marine safety of vessels to be passed by below the bridge. This paper aims to analyze the factors influencing maritime traffic safety and to figure out ample width of main span of these kinds of bridges through the reference study and FMSS.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.647-654
• /
• 2006

In orthotropic steel decks, it is likely to have defects due to fatigue damages because most of structural joints(the connection of longitudinal rib and transverse rib, the connection of deck plate and longitudinal rib) are connected by welds. However. orthotropic steel decks have many advantages. such as light weight and reduction of construction time. in comparison with concrete decks. Therefore. they are mostly used in long-span bridges and urban highway bridges. This study consists of the cause identication of fatigue damage and the suggestion of rational thickness on deck plate about the connection of deck plate and longitudinal rib. The results are as follows: fatigue damage cause at the connection of deck plate and longitudinal rib is local deformation in deck plate. And, rational thickness of deck plate is 16mm thickness.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.718-723
• /
• 2000

Reinforced concrete is in general, known as high durability construction material under normal environments due to strong alkalinity of cement. It is, however, well known that moderate or minor cracks in reinforced concrete should be most serious causes to deteriorate the durability of RC structures. Futhermore, chloride contents penetrating through unexpected cracks in reinforced concrete bridges get to weaken corrosion resistance of reinforcement steel in concrete and then to accelerate the deterioration of concrete durability. The objective of this experimental research is 1) to evaluate the effect of various corrosion protection systems for reinforced concrete specimens with moderate or minor cracks which are exposed to cyclic wet and dry seawater, and then 2) to develop effective corrosion protection systems for reinforced concrete bridges under the exposure of various detrimental environments such as seawater, deicing and etc.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.446-449
• /
• 1997

The use of high strength concrete in the fabrication and construction of prestressed concrete beam bridges can result in the increase of girder spacings for standard shapes, as well as the increase of span lengths. The increase of girder spacings corresponds to the reduction of the required number of girders. This study shows that the use of high strength concrete make prestressed concrete beam bridges the economical alternative to any other bridge types. Also, this study has the purpose of giving aids to design of prestressed concrete beam. To achieve this purpose this study provides the plots resulting from research on relationships between the concrete strength of prestressed concrete beam, girder spacing and the number of strands in various span lengths.

• Journal of KIBIM
• /
• v.7 no.1
• /
• pp.1-8
• /
• 2017

Aesthetic design guidelines of bridges were developed in many countries. As iconic structures, bridges need to be attractive and durable as they serve many generations. In this paper, a new design process of concrete structures considering 3D shapes and texture was proposed. The 3D design needs to consider function, economy, advanced technology, tradition and local culture. 3D printers enable the combination of artistic design and engineering design for concrete structures. Parametric modeling with iconic design was utilized to produce 3D formworks. As a pilot project, a railway bridge girder was designed and the proposed technologies were applied. Detail requirements to improve constructability and quality of concrete surfaces were derived. From the pilot applications, design guidelines were suggested.