• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.3
• /
• pp.224-232
• /
• 2015

In order to develop an active safety system which avoids or mitigates collisions with preceding vehicles such as autonomous emergency braking (AEB), accurate state estimation of the nearby vehicles is very important. In this paper, an algorithm is proposed using 3 dynamic models to better estimate the state of a vehicle which has various dynamic patterns in both longitudinal and lateral direction. In particular, the proposed algorithm is based on the Interacting Multiple Model (IMM) method which employs three different dynamic models, in cruise mode, lateral maneuver mode and longitudinal maneuver mode. In addition, a Probabilistic Data Association Filter (PDAF) is utilized as a data association algorithm which can improve the reliability of the measurement under a clutter environment. In order to verify the performance of the proposed method, it is simulated in comparison with a Kalman filter method which employs a single dynamic model. Finally, the proposed method is validated using radar data obtained from the field test in the proving ground.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.56-61
• /
• 2007

In the braking of railway rolling stock, the slip that is the relative velocity between train body and its wheel affects the adhesive force which is connected to the braking force. The coefficient of the adhesive force changes in accordance with the slip and the condition of a rail road. Namely, its value increases upon the maximum on a rail condition, and there it declines conversely while the magnitude of slip keeps rising on. First, this paper introduced a reference slip generator so that can utilize maximum adhesive forces with a disturbance observer for estimating unmeasurable current adhesive forces which is as an input of the generator. And, an adaptive sliding-mode control system has been synthesized for minimizing the error between reference and current slip. Finally the effectiveness of the proposed control system is evaluated by computer simulation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.19-27
• /
• 2017

In this paper, a simulator hardware and control design for an electronic parking brake (EPB) are proposed for emergency vehicle braking when the hydraulic break and anti-lock brake systems (ABS) fail to function. EPB systems are designed specifically for park braking and are usually installed on the rear wheels. However, in an emergency situation when all vehicle brake systems fail, the EPB can be utilized to stop the vehicle and track the target slip ratio as the ABS. This paper analyzed the non-linear EBP of the type of motor on caliper (MoC) based on experiments. A simulator hardware is also designed to validate the performance of the designed EPB controller in terms of braking distance and performance in tracking the target slip ratio. Through the experimental analysis, it is confirmed that a sliding mode controller can be applied on a non-linear EPB to track the target slip ratio.

• Journal of Auto-vehicle Safety Association
• /
• v.5 no.1
• /
• pp.16-24
• /
• 2013

Some GM (General Motors) vehicles are using a GMLAN (General Motors Local Area Network) communication protocol for control and diagnostics. The airbag control module uses vehicle speed information from the GMLAN to record the vehicle speed as pre-crash information. In order to use the vehicle speed information for crash reconstruction purposes, it helps to be able to understand the accuracy of the data. The actual vehicle speed is not expected to be the same as the GMLAN indicated speed in some situations like a spin or if there is hard braking. This paper compares the actual vehicle speed and vehicle speed information during specific vehicle maneuvers. Actual vehicle speed is calculated from a GPS sensor, while GMLAN vehicle speed is calculated from transmission output sensor by the Engine control module (ECM). Vehicle maneuvers defined as Mode #1, Mode #2, Mode #3. The Mode #1 maneuver simulates wheel lock-up and skidding f by hard-braking at a specific speed. The Mode #2 maneuver simulates a 90degree turn using a J-turn maneuver at a specific speed. The Mode#3 maneuver simulates a 180 degree turn using a spin type of maneuver at a specific speed. The study then compares the GMLAN speed and GPS speed to see what speed difference exists between them. The results of this paper are applicable to GM vehicles only. This paper catalogs the performance and limitations of two vehicles as useful reference for crash reconstructions where there is a need to understand the speed indicated in the pre-crash section of the SDM data.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1132-1137
• /
• 2008

Automatic Operation based on ATO (Automatic Train Operation) is necessary for driverless Light Rail Transit business. When this kind of driverless LRT operation plan is made, TPS (Train Performance Simulation) is traditionally simulated at all-out mode and coasting mode based on manual operation. Commercial schedule speed equals to all-out speed minus $9{\sim}15%$ make-up margin. Coasting mode TPS simulation is also run at commercial schedule speed to calculate run time and energy consumption. But TPS based on manual operation should make an improvement on accuracy in case of driverless LRT operation Plan. In this paper, new fast mode TPS simulation using ATO pattern is proposed and show near actual ATO result. The actual ATO pattern can be accurately simulated with the introduction of 4 parameters such as commercial braking rate, jerk, station stop profile and grade converted distance. Normal mode TPS simulation for commercial schedule speed can be designed to have fast mode trip time plus 3 seconds/km margin recommended by korean standard LRT specification.

• Journal of Korean Society for Atmospheric Environment
• /
• v.29 no.5
• /
• pp.656-667
• /
• 2013

The non-exhaust coarse, fine, and ultrafine particles were characterized by on-road driving measurements using a mobile sampling system. The on-road driving measurements under constant speed driving revealed that mass concentrations of roadway particles (RWPs) were distributed mainly in a size range of 2~3 ${\mu}m$ and slightly increased with increasing vehicle speed. Under braking conditions, the mode diameters of the particles were generally similar with those obtained under constant speed conditions. However, the PM concentrations emitted during braking condition were significantly higher than those produced under normal driving conditions. Higher number concentrations of ultrafine particles smaller than 70 nm were observed during braking conditions, and the number concentration of particles sampled 90 mm above the pavement was 6 times higher than that obtained 40 mm above the pavement. Under cornering conditions, the number concentrations of RWPs sampled 40 mm above the pavement surface were higher than those sampled 90 mm above the pavement. This might be explained that a nucleation burst of a lot of vapor evaporated from the interaction between the tire and the road pavement under braking conditions continuously occurred by cooling during the transport to the sampling height 90 mm, while, for the case of cornering situations, the ultrafine particle formation was completed before the transport to the sampling height of 40 mm.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2009.06a
• /
• pp.181-182
• /
• 2009

In the machinery, the brake system is as important part as machine's working. If the machine doesn't stopped, would be big occident. For the ships, it is important too. Use the windlass winch to stop the voyage and use mooring winch to keep the stop in the port. In this study, improve the braking power divided the brake band and search the optimize portion.

• Journal of Auto-vehicle Safety Association
• /
• v.15 no.3
• /
• pp.59-65
• /
• 2023

As advanced driving assistance system (ADAS) and autonomous driving performance continue to improve, existing crash accidents and crash types are changing. Accordingly, the collision angle and the seating posture of the occupant are changed. It is necessary to study how the occupant injury mechanism changes according to these different crash types. In this regard, a representative crash test mode was derived when the automatic emergency braking system (AEB), one of the autonomous driving performance, was applied to the representative car-to-car crash scenario in Korea. The derived crash test mode was used to analyse the mechanisms of collision injuries according to both impact angle and the occupant seating posture (reclined seat-back angle). The results obtained through this study can be utilized as reference data for the development of new crash evaluation methods and improvements in crash restraint systems for enhancing crash safety.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.169-176
• /
• 2002

Axial crushing behavior of cylindrical shell Is utilized in the braking of the high-velocity impacting object. In this paper, truncated cone shape brake device is introduced. That is, thickness of the shell is increased gradually from the impacting end to the other end. A detailed experimental investigation on the quasi-static axial crushing behavior of truncated cone type brake devices has been performed. Specimens of various shape were tested to check the influence of design parameters such as length, radius, mean thickness, and conical angle of cylinder. Influence of the material properties were also investigated by adopting aluminum, low carbon steel, and stainless steel as constructing materials. By analyzing deformation procedures of the specimens, it is seen that conical angle influence the deformation mode and the sequence of the wrinkles generation. Braking distance and mean braking force of each specimen were predicted based on the crushing load measured from the tests.

• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.120-131
• /
• 2011

This paper proposes two control strategies for the bidirectional Z-source inverters (BZSI) supplied by batteries for electric vehicle applications. The first control strategy utilizes the indirect field-oriented control (IFOC) method to control the induction motor speed. The proposed speed control strategy is able to control the motor speed from zero to the rated speed with the rated load torque in both motoring and regenerative braking modes. The IFOC is based on PWM voltage modulation with voltage decoupling compensation to insert the shoot-through state into the switching signals using the simple boost shoot-through control method. The parameters of the four PI controllers in the IFOC technique are designed based on the required dynamic specifications. The second control strategy uses a proportional plus resonance (PR) controller in the synchronous reference frame to control the AC current for connecting the BZSI to the grid during the battery charging/discharging mode. In both control strategies, a dual loop controller is proposed to control the capacitor voltage of the BZSI. This controller is designed based on a small signal model of the BZSI using a bode diagram. MATLAB simulations and experimental results verify the validity of the proposed control strategies during motoring, regenerative braking and grid connection operations.