• International Journal of Aerospace System Engineering
• /
• v.2 no.2
• /
• pp.6-9
• /
• 2015

A new cross disciplinary conception of transitional aero-optics is built up during analyzing and measuring the linkage between the hypersonic boundary layer transition on a flat plate and the jittering characteristics of the small-aperture beam through that boundary layer. Based on that conception, the Small-Aperture Beam Technique (SABT) and high-speed Imaging Camera System (ICS) used in aero-optical studies are considered as new techniques for the assessment of the hypersonic transition in the boundary layer on a flat plate. In the FD-20 gun tunnel, for the free stream parameters with Mach number of 8 and unit Reynolds number of $1{\times}10^7$ (1/m), those two optical techniques are used to measure the jitter of the small-aperture beam. At the same free stream parameters, the distribution of the heat transfer along the centerline of the flat plate is also measured by the thin film resistance gauge technique. The results show the similarity of the increase trend between the heat transfer and the jitter of the small-aperture beam in the transitional region. It helps us to surmise that it may be feasible to diagnose the transition in a hypersonic boundary layer on a flat plate by means of those above optical techniques.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.3
• /
• pp.1-1
• /
• 1987

The accurate prediction of the ship wave resistance is very important to design ships which operate satisfactorily in a wave environment. Thus, work should continue on development and validation of methods to compute ship wave patterns and wave resistance. Research efforts to improve the prediction of ship waves and wavemaking resistance are categorized in two major areas. First is the development of higher-order theories to take account of the nonlinear effect of the free surface condition and improved analytical treatment of the body boundary condition. Second is the development of direct numerical methods aimed at solving body and free-surface boundary conditions as accurately as possible. A new formulation of the slender body theory for a ship with constant speed is developed by Maruo. It is quite different from the existing slender ship theory by Vossers, Maruo and Tuck. It may be regarded as a substitute for the Neumann-Kelvin approximation. In present work, the method of asymptotic expansion of the Kelvin source is applied to obtain a new wave resistance formulation in fluid of finite depth. It takes a simple form than existing theory.

• Journal of Environmental Science International
• /
• v.11 no.7
• /
• pp.663-667
• /
• 2002

The aerodynamic resistance($R_a$) to vertical transfer in the surface boundary layer can be formulated in terms of the friction velocity, height of observation, vertical heat flux and surface roughness. Unlike previous studies which focused on the role of $R_c$, present study perform additional tests using a variety of $R_a$ formulae. Several $R_a$ formulations available in the literature, suitable for unstable conditions, were tested for their influence on the dry deposition velocity. The canopy resistance($R_c$) determines the shape of the diurnal pattern, while a small amplitude diurnal cycle in $V_d$ was attributed to the aerodynamic resistance. The aerodynamic resistance is the major contributor to the formation of spikes in nighttime and $R_a$ is relatively important at night because the canopy resistance is smaller. All formulations show similar diurnal cycle and yield good agreement with the observations. Although present $V_d$ formulations are suitable for numerical air qualify models, the research must continue for further improvements in resistance parametrizations.

• Journal of Ship and Ocean Technology
• /
• v.9 no.3
• /
• pp.1-13
• /
• 2005

A design procedure for a ship with minimum total resistance has been developed using a numerical optimization method called SQP (Sequential Quadratic Programming) to search for optimized hull form and CFD(Computational Fluid Dynamics) technique. The friction resistance is estimated using the ITTC 1957 model-ship correlation line formula and the wave making resistance is evaluated using a potential-flow panel method based on Rankine sources with nonlinear free surface boundary conditions. The geometry of hull surface is represented and modified using B-spline surface patches during the optimization process. Using the Series 60 hull ($C_B$ =0.60) as a base hull, the optimization procedure is applied to obtain an optimal hull that produces the minimum total resistance for the given constraints. To verify the validity of the result, the original model and the optimized model obtained by the optimization process have been built and tested in a towing tank. It is shown that the optimal hull obtained around $13\%$ reduction in the total resistance and around $40\%$ reduction in the residual resistance at a speed tested compared with that of the original one, demonstrating that the present optimization tool can be effectively used for efficient hull form designs.

• Geomechanics and Engineering
• /
• v.33 no.5
• /
• pp.519-528
• /
• 2023

In this paper, we present the results of an experimental study on the effect of polymer support fluid on shaft resistance of offshore bored piles. A series of pullout tests were performed on bored piles installed under various boundary conditions considering different types of grounds and support fluids, and a range of support fluid exposure times. Contrary to previous studies concerning onshore bored piles, a time dependent effect of polymer fluid on shaft resistance was observed in all ground types. The adverse effect of polymer support fluid on the shaft resistance, however, was considerably less than bentonite support fluid for a given exposure time. No significant reduction in shaft resistance was evident when limiting the exposure time of the polymer support fluid to the side wall of the borehole within 2-3 hours. The degree to which the polymer fluid affects shaft resistance seemed to vary with the ground type. A proper consideration should be given to the time dependent effect of polymer fluid on shaft resistance of bored piles installed in offshore construction environment to limit its adverse effect on the pile performance. The practical implications of the findings are discussed.

• Journal of the Korean Mathematical Society
• /
• v.44 no.3
• /
• pp.707-717
• /
• 2007

Arches are constrained with rotational resistance at both edges. An energy method is used to derive variational formulation which is used to prove the existence of equilibrium states of elastic circular arches for the torsional spring constants ${\rho}-\;{\geq}\;0,\;{\rho}+\;{\geq}\;0,\;and\;{\rho}-\;+\;{\rho}+\;>\;0$. The boundary conditions are searched using the existence of minimum potential energy.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.813-817
• /
• 1987

High value sheet resistance (Rs' 1K-33K\ulcorner/) polysilicon resistors were fabricated using double ion implantation with boron as the major dopant and phosphorus compensation. It is observed that Rs sensitivity to the net doping concentration is decreased by one order of magnitude compared to the conventional (boron implanted)polysilicon resistors. The temperature co-efficient of resistance (TCR) measured between 25\ulcorner and 125\ulcorner shows equivalent values to those of non-compensated resistors for the same Rs. A qualitative electrical conductiion mechanism for compensated polysilicon resistor is proposed, based on the existing grain boundary charge trapping theory.

• 한국초전도학회:학술대회논문집
• /
• v.15
• /
• pp.43-43
• /
• 2005

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.1
• /
• pp.109-118
• /
• 2003

The recent trend towards miniaturization causes an increased demand for parts with very small dimensions. Milli-structure components are classified as a component group whose size is between macro- and micro-scale. The manufacturing process of these components of thin sheet metal forming has a microscopic properties in addition to a typical phenomenon of bulk deformation because of the forming size. Also, the material properties and the deformation behavior change with miniaturization, which means that, a coarse grained materials show a higher resistance against deformation, when the grain size is in the range of the sheet thickness. In this study, a new numerical approach is proposed to simulate intergranular milli-structure in forming by the finite element method. The grain element and grain boundary element are introduced to simulate the milli-structure in the bending. The grain element is used to analyze the deformation of individual grain while the grain boundary element is for the investigation on the movement of the grain boundary. Also, the result of the finite element analysis is confirmed by a series of milli-sized forming experiments.

• Journal of Welding and Joining
• /
• v.31 no.3
• /
• pp.31-38
• /
• 2013

The transition of serrated grain boundary and its effect on liquation behavior in the simulated weld heat-affected zone (HAZ) have been investigated in a wrought Ni-based superalloy Alloy 263. Recently, the present authors have found that grain boundary serration occurs in the absence of adjacent coarse ${\gamma}^{\prime}$ particles or $M_{23}C_6$ carbides when a specimen is direct-aged with a combination of slow cooling from solution treatment temperature to aging temperature. The present study was initiated to determine the interdependence of the serration and HAZ property with a consideration of this serration as a potential for the use of a hot-cracking resistant microstructure. A crystallographic study indicated that the serration led to a change in grain boundary character as special boundary with a lower interfacial energy as those terminated by low-index {111} boundary planes. It was found that the serrated grain boundaries are highly resistant to boron enrichment, and suppress effectively grain coarsening in HAZ. Furthermore, the serrated grain boundaries showed a higher resistance to susceptibility of liquation cracking. These results was discussed in terms of a significant decrease in interfacial energy of grain boundary by the serration.