• The KSFM Journal of Fluid Machinery
• /
• v.13 no.2
• /
• pp.5-11
• /
• 2010

The nanofluidics is characterized by a large surface-to-volume ratio, so that the surface properties strongly affect the flow resistance. We present here the results showing that the effect of wetting properties and the surface roughness may considerably reduce the friction of fluid past the boundaries. For a simple fluid flowing over hydrophilic and hydrophobic surfaces, the influences of surface roughness are investigated by the nonequilibrium molecular dynamics (NEMD) simulations. The fluid slip at near a solid surface highly depends on the wall-fluid interaction. For hydrophobic surfaces, apparent fluid slips are observed on smooth and rough surfaces. The solid wall is modeled as a rough atomic sinusoidal wall. The effects on the boundary condition of the roughness characteristics are given by the period and amplitude of the sinusoidal wall. It was found that the slip velocity for wetting conditions at interface decreases with increasing effects of surface roughness. The results show the surface rougheness and wettability determines the slip or no-slip boundary conditions. The surface roughness geometry shows significant effects on the boundary conditions at the interface.

• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.22-27
• /
• 2014

In the past, cold crack was commonly observed in the HAZ(heat affected zone) of high-strength steels. Applying to TMCP(thermo-mechanical controlled process) and HSLA(high strength low alloy) steels, cold crack tends to increase the occurrence in the weld metal. It is generally understood that cold crack occurs when the following factors are present simultaneously : diffusible hydrogen in the weld metal, a susceptible microstructure and residual stress. In particular, many studies investigated the microstructural effect on the cold crack in HAZ and the cold crack in weld metals starts to receive the special attendance in modern times. The purpose of the study is to review the effect of weld microstructures (grain boundary ferrite, Widm$\ddot{a}$nstatten ferrite, acicular ferrite, bainite and martensite) on cold crack in the weld metals. Among various microstructures of weld metals, acicular ferrite produced the greatest resistance to the cold crack due to the fine interlocking nature and high-angle grain boundary of the microstructure.

• Corrosion Science and Technology
• /
• v.19 no.1
• /
• pp.37-42
• /
• 2020

Even though 304 low-carbon (304L) stainless steel was developed to enhance the resistance to intergranular corrosion and stress corrosion cracking, it is occasionally subject to degradation in harsh environments. The degree of sensitization (DOS) of 304L stainless steel was studied as a function of sensitization using a double-loop electrochemical potentiokinetic reactivation (DL-EPR) method. Sensitizing heat treatment was performed in an Ar atmosphere at 500℃, 600℃, and 700℃, with heat treatment times varying from 0 to 96 h. DOS was measured by the ratio of the peak current density value of the forward scan to that of the reverse scan. After the EPR experiment, the specimen surface was observed by scanning electron microscopy and energy dispersive spectroscopy. The DOS of the specimens heat-treated at 600℃ increased with heat treatment times up to 48 h and then decreased due to a self healing effect. The DOS was higher in specimens heat-treated at 600℃ than those at 500℃ or 700℃. Corrosion of the sensitized specimens occurred mainly at the δ-γ phase boundary. The corrosion morphology at the δ-γ phase boundary changed with sensitizing heat-treatment conditions due to differences in chromium activity in γ austenite and δ ferrite.

• Journal of Computational Design and Engineering
• /
• v.3 no.3
• /
• pp.215-225
• /
• 2016

In recent years, the automotive industry has known a remarkable development in order to satisfy the customer requirements. In this paper, we will study one of the components of the automotive which is the twist beam. The study is focused on the multicriteria design of the automotive twist beam undergoing linear elastic deformation (Hooke's law). Indeed, for the design of this automotive part, there are some criteria to be considered as the rigidity (stiffness) and the resistance to fatigue. Those two criteria are known to be conflicting, therefore, our aim is to identify the Pareto front of this problem. To do this, we used a Normal Boundary Intersection (NBI) algorithm coupling with a radial basis function (RBF) metamodel in order to reduce the high calculation time needed for solving the multicriteria design problem. Otherwise, we used the free form deformation (FFD) technique for the generation of the 3D shapes of the automotive part studied during the optimization process.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.601-604
• /
• 1998

NOX detecting gas sensors using TiO2 doped tungsten oxide semiconductor were prepared and their electrical and sensing characteristics have been investigated. In normal air condition, the sensors of WO3, TiO2 doped WO3 show grain boundary heights of 0.34 eV, 0.25 eV, respectively. The grain boundary barrier energy variation was increased by doping TiO2 into large variation of resistance to NOX gases. And doping the TiO2 4 wt.%, the particle size of WO3 polycrystal films showed higher sensitivity and better sorption characteristics to NOX gas than the pure WO3 films material in air at operating temperature of $350^{\circ}C.$ The TiO2 doped WO3 semiconductor gas sensor shows nano-sized particle size and good sensitivity to sub-ppm concentration of NOX.

• Journal of the Korean Ceramic Society
• /
• v.24 no.3
• /
• pp.270-276
• /
• 1987

The microstructure and dielectric properties of a SrTiO3-based GBL (Grain Boundary Layer) capacitor were investigated. The 0.6 mol% Nb2O5 doped SrTiO3 was sintered for 3 hr at 1450$^{\circ}C$ in mixed gas(N2/H2) atmosphere. The Nb2O5 promoted the grain growth of the SrTiO3 ceramics was decreased with the amount of Nb2O5. The oxide mixture(PbO, Bi2O3, B2O3) were painted on the reduced specimen and fired at 1000$^{\circ}C$ to 1100$^{\circ}C$ in air. The penetrated oxide mixture into specimen were located in grain boundaries. A SrTiO3-based GBL capacitor had the apparent permittivity of about 3.0${\times}$104, the dielectric loss of 0.01-0.02, and insulating resistance of 108-109$\Omega$.cm. The capacitor had the stable temperature coefficient of capacitance and exhibited dielectric dispersion over 107 Hz. The capacitance-voltage measurements indicated that the grain boundary was composed of the continuous insulating layers.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.66-71
• /
• 1998

A study of treatment effects on laser surface melted Ni-base alloy 600, especially on precipitation behavior ad chemical composition changes on the grain boundary were conducted with microscopic equipments. Long-term aging treatment at 40$0^{\circ}C$ caused no considerable effects on the grain boundary properties. Cr-rich M$_2$$_3$C$_{6}$ and Cr$_{7}$C$_3$ carbides were precipitated and the resultant Cr depletion below 12 wt pct on some high angle grain boundaries was occurred by heat treatment at $600^{\circ}C$ for 24 hours. These results can imply that the resistance of intergranular stress corrosion cracking of heat treated alloy 600 might not be changed considerably in comparion with the as-LSM one.e.e.

• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.777-783
• /
• 1994

Oxidation behavior of hot-pressed silicon nitride ceramics with various sintering additives has been investigated. The weight gain of each specimens has shown in the range of 0.11 mg/$\textrm{cm}^2$ ~3.4 mg/$\textrm{cm}^2$ at 140$0^{\circ}C$ for 192 h and eleven compositions have shown good oxidation resistance with the weight gain below 0.5 mg/$\textrm{cm}^2$. The oxidation rate has been shown to obey the parabolic rate law and the oxidized surface has consisted of $\alpha$-cristobalite and M2Si2O7 or MSiO3 (M=rare earth or transition metals) phase. The oxidation rate of each specimens has related to the eutectic temperature between additive oxide and SiO2, and ionic radius of additive oxides, respectively. From the above results, it could be concluded that the oxidation behavior of hot pressed silicon nitride is dominated by the high temperature properties of grain boundary glassy phase and the high temperature properties of grain boundary glassy phase are affected by the ionic radius of additive oxides.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.3
• /
• pp.157-162
• /
• 2005

In order to evaluate the corrosion of reinforcing steel-bars (rebar) in concrete, a nondestructive evaluation by the half-cell potential method is currently applied. In this study, potentials measured on a concrete surface are compensated into those on the concrete-rebar interface by the inverse boundary element method (IBEM). Because these potentials are obtained three-dimensionally (3-D), 3-D visualization is desirable. To this end, a visualization system has been developed by using VRML (Virtual Reality Modeling Language). As an application, results of a reinforced concrete (RC) slab with corroded rebars are visualized and discussed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.153.2-158
• /
• 1999

A study has been made to investigate how the fomability of Ti-10V-2Fe-3Al alloy is related to the initial microstructure and process variables such as temperature and strain rate. It has been found that the deformation resistance at high temperature is increased with the increase in the thickness of grain boundary a (GB)a and/or acicular a phase and however the effect of a morphology on the hot formability is considered insignificant due to the breakage of GB a and/or acicular a into several equiaxed a particles