• Macromolecular Research
• /
• v.9 no.1
• /
• pp.45-50
• /
• 2001

Formation of bound rubber depends on the filler-polymer interactions including physical adsorption, chemisorption, and mechanical interaction. Bound rubbers consist of tightly and loosely bound ones. Styrene-butadiene rubber (SBR) is composed of styrene, 1,2-, cis-1,4-, and trans-1,4-units. Filler-polymer interactions of each components of SBR with fillers, carbon black and silica, were studied by analysis of microstructure of the bound rubber. Filler-polymer interaction of the 1,2-unit with the fillers was found to be stronger than those of the other components and this phenomenon was shown more clearly in the tightly bound rubber.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.196-204
• /
• 2015

Crosslink density of a rubber vulcanizate determines the chemical and physical properties, while bound rubber is an important factor to estimate reinforcement of a filled rubber compound. Extender oil is added to a raw rubber with very high molecular weight for improving processability of a rubber composite. Influence of extender oil on crosslink density, bound rubber formation, and physical properties of solution styrene-butadiene rubber (SSBR) composites with differing microstructures was investigated. Crosslink densities of non-oil-extended SSBR (NO-SSBR) vulcanizates were higher than those of oil-extended SSBR (OE-SSBR) ones. Bound rubber contents of NO-SSBR compounds were also greater than those of OE-SSBR ones. The experimental results could be explained by interfering of extender oil. The OE-SSBR vulcanizates had low modulus but long elongation at break, whereas the NO-SSBR ones had high modulus but short elongation at break. It was found that the crosslink densities affected the physical properties more than the bound rubber contents. The moduli increased with increase in the crosslink density irrespective of extender oil, while the elongation at break decreased. Each variation of the tensile strengths of NO-SSBR and OE-SSBR vulcanizates with the crosslink density showed a decreasing trend. Tear strength of the OE-SSBR vulcanizate increased with increase in the crosslink density, whereas variation of the tear strength of NO-SSBR vulcanizate with the crosslink density showed a weak decreasing trend.

• Structural Engineering and Mechanics
• /
• v.30 no.3
• /
• pp.351-368
• /
• 2008

The purpose of this paper is to propose a simple analysis method of axial deformation of base-isolation rubber bearings in a building subjected to earthquake loading and present its applicability to the analysis of the bound of the aspect ratio of base-isolated buildings. The base shear coefficient is introduced as a key parameter for the bound analysis. The bound of the aspect ratio of base-isolated buildings is analyzed based on the relationship of the following four quantities; (i) ultimate state of the tensile stress of rubber bearings based on a proposed simple recursive analysis for seismic loading, (ii) ultimate state of drift of the base-isolation story for seismic loading, (iii) ultimate state of the axial compressive stress of rubber bearings under dead loads, (iv) prediction of the overturning moment at the base for seismic loading. In particular, a new recursive analysis method of axial deformation of rubber bearings is presented taking into account the nonlinear tensile behavior of rubber bearings and it is shown that the relaxation of the constraint on the ultimate state of the tensile stress of rubber bearings increases the limiting aspect ratio.

• Elastomers and Composites
• /
• v.54 no.2
• /
• pp.142-148
• /
• 2019

In this study, the effects of filler particle size and shape on the physical properties of silicone rubber composites were investigated using inorganic fillers (Minusil 5, Celite 219, and Nyad 400) except silica, which was already present as a reinforcing filler of silicone rubber. Fillers with small particle sizes are known to facilitate the formation of the bound rubber by increasing the contact area with the polymer. However, in this experiment, the bound rubber content of Celite 219-added silicone composite was higher than that of Minusil 5-added silicone composite. This was attributed to the porous structure of Celite 219, which led to an increase in the internal surface area of the filler. When the inorganic fillers were added, both thermal decomposition temperature and thermal stability were improved. The bound rubber formed between the silicone rubber and inorganic filler affected the degree of crosslinking of the silicone composite. It is well-known that as the size of the reinforcing filler decreases, the reinforcing effect increases. However, in this experiment, the hardness of the composite material filled with Celite 219 was the highest compared to the other three composites. Furthermore, the highest value of 2.19 MPa was observed for 100% modulus, and the fracture elongation was the lowest at 469%. This was a result of excellent interaction between Celite 219 filler and silicone rubber.

• Elastomers and Composites
• /
• v.33 no.1
• /
• pp.44-51
• /
• 1998

The purpose of this experiments were investigated on the physical properties of rubber com-pounds containing two types carbon black. Bound rubber and interaction coefficient for com-pounds with pure carbon black were higher than those for the compounds with dual phase carbon black. Slightly higher values in 300% modulus and tensile strength indicated that the ratio of rubber-filler bound to rubber-rubber bound of pure carbon black were higher than those of com-pounds with dual phase carbon black. It was founded that dynamic properties, that is rebound, heat build-up, 0 & $60^{\circ}C$ tan $\delta$, and cut and chip loss of compounds with dual phase carbon black were better than those of compounds with pure carbon black, but abrasion property of dual phase carbon black was lower than those of pure carbon black because of low reinforcing ability.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.37-43
• /
• 2001

Influence of the filler composition ratio on cure characteristics and bound rubber content of the compounds and on physical properties of the vulcanizates were studied using both silica and carbon black-filled styrene-butadiene rubber (SBR) compounds with the total filler content of 80.0 phr. The bound rubber content increased slightly with increase of the silica content ratio. The viscosity also increased with increasing the silica content ratio, especially increased steeply after the silica content of 60.0 phr. The cure times obtained with a rheometer, t2, t40, and t90, are increased by increasing the silica content ratio and the cure rate decreased. The delta torque increased with the increased silica content ratio. Variation or the modulus with the silica content ratio showed a decreased trend though the delta torque increased. The tan ${\delta}$ at $60^{\circ}C$ decreased with increased of the silica content ratio.

• Elastomers and Composites
• /
• v.17 no.1
• /
• pp.13-21
• /
• 1982

The purpose of this dissertation is to compare bound andtioxidant, MHPPD with the ordinary one, IPPD, when high polymers are used like NR and SBR. The effect of rubber bound antioxidant and ordinary antioxidant on the Mooney scorch time has been studied by means of the Mooney viscometer. The ageing properties of vulcanizates containing rubber-bound antioxidant and ordinary antioxidant have been studied in terms of hardness, tensile strength and elongation. The results of the Mooney scorch time and ageing properties are as follows: When MHPPD was mixed with NR or SBR compounds, the Mooney scorch time was faster than the IPPD compounds. Also the ageing properties of the vulcanizates containing MHPPD were much superior to the IPPD compounds. Furthermore, the vulcanizates comporised of MHPPD have taken andvantage of and resistance in the ozone test.

• Applied Chemistry for Engineering
• /
• v.5 no.6
• /
• pp.943-948
• /
• 1994

The properties of uncured rubber compound and swelling behavior of cured rubber compound with carbon black(N33O grade) increment. Bound Rubber content(BRC) increased according to carbon black increment and ${\alpha}_f$, behavior of uncured rubber compound filled with carbon black, was 1.46. Carbon black added to rubber compound showed behavior of spherical particle by bound rubber. The $C_1$ values of cured rubber compounds, which measured by the stress-strain method of Mooney-Rivlin, increased with carbon black increment.

• Elastomers and Composites
• /
• v.40 no.1
• /
• pp.29-36
• /
• 2005

Mixing condition and procedure affect properties or a filled rubber compound such as filler dispersion, viscosity, and bound rubber formation. Influence of separate load of styrene-butadiene rubber (SBR) and acrylonitrile-butadiene rubber (NBR) on properties or silica-filled SBR compounds containing NBR was studied. Cure time and cure rate became faster as NBR content increased. The crosslink density increased with increase in the NBR content. The bound rubber content also increased as the NBR content increased. NBR content of the bound rubber was higher than that of the compounded rubber. The bound rubber content was higher when SBR and NBR were loaded separately than when loading simultaneously. The cure time and cure rate were slower for the separate load than for the simultaneous one. The crosslink density was also lower for the former case than for the latter one.

• Elastomers and Composites
• /
• v.52 no.1
• /
• pp.17-21
• /
• 2017

The optimum mixing conditions of silica and silane containing rubber composites were evaluated by investigating the properties of rubber composites prepared with a silica composition of 10, 20, 40, 60, and 80 g, respectively. The crosslinking rate decreased with increasing silica content, with he promoters being adsorbed on the silica surface with in the rubber composite. As a result, the increase in crosslinking time resulted in the destruction of the silica structure. The increase of the bound rubber content due to the destruction of the silica structure inhibited the chain motion of the polymer molecules and reduced the cohesion of the silica itself. Finally, the increase of silica content showed the increase of hardness, tensile strength, and storage modulus of rubber composites.