• 한국정밀공학회지
• /
• 제28권6호
• /
• pp.709-715
• /
• 2011

Chattering in cutting operations are usually a cumbersome part of the manufacturing process in mechanical. Particular, machining performance such as that of the boring process is limited by cutting condition at the movable components. Among various sources of chatter vibration, detrimental point in cutting condition is found a mechanical condition on overhang. It limits cutting speed, depth, surface roughness and tool wear failure as result because the all properties are varying with the metal removal process. In this case, we have to observe the resonance frequencies of a boring bar for continuous cutting. In the established research, boring bar vibration of cutting system has been measured with the aid of accelerometer. However, the inherent parameters of internal turning operations are severely limit for the real time monitoring on accelerometers. At this point, this paper is proposed other method for real time monitoring during continuous cutting with optical fiber at the inside of boring bar. This method has been used a plastic fiber in the special jig on boring bar by based on experimental modal analysis. In this study, improvement of monitoring system on continuous internal cutting was attempted using optical fiber sensor of inside type because usually chattering is investigated experimentally measuring the variation in chip thickness. It is demonstrated that the optical fiber sensor is possibility to measure of chattering with real time in boring process.

• 한국기계가공학회지
• /
• 제19권6호
• /
• pp.49-54
• /
• 2020

The purpose of this study is to investigate the effects of the change in the spindle speed and the feed rate on the diameter change of a hole using a boring cutter for the internal boring process of AL6061-T4 alloys. The experimental results are quantitatively analyzed by applying the factor analysis and the response surface analysis of the experimental design method. The tendency of the diameter change according to the change in the spindle speed and feed level is also evaluated. During the internal boring process of AL6061-T4 alloys, the main factor affecting the diameter change is the spindle speed in which the diameter decreases as the number of revolutions increases. In addition, the diameter tends to increase as the feed is increased; however, as the number of spindle revolutions increases, the influence of the feed decreases.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.82-87
• /
• 2011

Lubrication has an important role to reduce frictional forces and temperature between cutting chips and the face of a tool. However, it has harmful effects to workers' health and working environment. The purpose of this thesis is to find cutting conditions through the quality analysis in boring for SM45C steel using MQL(Minimum Quantity Lubrication). Machining process is super drill, tip drill, end mill and boring in order. Experimental factors of boring and the quantity of mist air are properly selected. With the analysis of experimental data, this thesis shows that boring with MQL improves the surface roughness when spindle speed is 934rpm or feeding speed is 74mm/min.

• 한국공작기계학회논문집
• /
• 제17권2호
• /
• pp.58-64
• /
• 2008

The cutting process of materials is accompanied with the elastic and plastic deformation due to chucking forces in the boring process of thin holes on the turning. Upon removal of chucking forces at the end of process, the original shape is remained in the plastic deformation; on the other hand, it is modified in the elastic deformation due to spring back. Fixing materials by chucks on the turning has influence on roundness because the process is conducted with unbalanced distribution load induced from the fixing of three jaws. Moreover, the amount of spring back depends on the magnitude of fixing forces. We studied the change of roundness according to fixing forces as well as the method to reduce the influence of chucking forces.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.30-35
• /
• 2008

As demands for being economical, precise drilling process is on the increase. Therefore, the objective of this study is to develop a step cutter that can be controllable through micro dimension and can be changed from separate manufacturing processes of drilling and boring into an integrated one. In order to attain this object the step cutter is designed with a 3D geometric modeling and the design could be modified easily by using parametric modeling methodology. Also, collision is not occurred during manufacturing process because of cutting simulation. The step cutter is assembled by parts made up of 5-axis machining and sintering. Validation tests are accomplished. They show that developed cutter has characteristics such as reduction of machining time as well as the good surface roughness of the machined hole. Indeed, reliability could be obtained from a durability test.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.7-12
• /
• 2017

It is assumed that the buckling and cutting conditions depending on the slenderness ratio will affect the machining quality of the rotary boring tool mounted on a milling machine. In this study, the boring cutter was designed and fabricated to precisely create the Ø30 hole. Through the performance evaluation, the accuracy of the hole according to the slenderness ratio and cutting conditions was analyzed, and the following conclusions were obtained. The higher the RPM, the smaller the change in the working diameter, and the smaller the hole. Next, the smaller the slenderness ratio, the smaller the change in straightness due to the change in cutting conditions. Finally, the slenderness ratio also affects the tendency for changes in the concentricity. The larger the slenderness ratio, the more sensitive the concentricity to changes in cutting conditions.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.658-664
• /
• 2013

In this paper, we present a case study of vibration suppression based on the application of active damping to the small boring process of a boring bar with diameter below ${\Phi}12$. The proposed active damping system consists of an acceleration sensor for real-time monitoring of the vibration signal, a driver for phase control in a computer program, and piezoelectric actuators for damping. In this system, the vibration signals are detected by the acceleration sensor and sent to the computer as an input. The phase shift parameter of the natural frequency of the input signal is sent to the data acquisition board in the computer and calculated by the phase control program. This study confirmed the effectiveness of this damping system, and it opens up the possibility of the development of active damping systems for small boring processes.

• 한국기계가공학회지
• /
• 제8권3호
• /
• pp.98-104
• /
• 2009

The objective of this paper is to investigate the effect of factors on the dynamic stiffness variation of boring bar. The experiment was carried out by Taguchi Method and Orthogonal array table. The results indicate that overhang was found out to be dominant factor with 95% confident intervals and feed rate and depth of cut were insignificant. In addition, analysis of loss function shows that loss value increased sharply from 3D to 4D(D is a shank diameter). Consequently, there is critical point which changes property of dynamic stiffness.

• 전기전자학회논문지
• /
• 제23권1호
• /
• pp.22-28
• /
• 2019

본 연구는 차량용 보링 생산 공정에서 기계적인 에러를 체크하기 위한 품질 체크용 모니터링 시스템을 개발한다. 기계적인 에러는 이상적인 절단경로와 비교하여 실제 절단경로의 공간위치 차이에서 나타난다. 제조공정 제품의 오차를 모니터하기 위해 제품의 인지왜곡, 죄임 에러, 기계공구의 회전과 운동에러의 반경회전과 같이 보링 품질에 영향을 미치는 다수 요소들을 설명한다. 생산품질을 입증하기 위해 IT 융합에 기반한 공정 에러율을 분석하고 분석 데이터를 메모리에 저장하는 품질체크 방법을 제안한다. 따라서 불량 생산 제품을 감지함으로써, 생산 코스트와 베어링의 손실을 줄일 수 있다.

• 한국환경과학회지
• /
• 제15권1호
• /
• pp.95-100
• /
• 2006

Heat transfer and flow characteristics in a pipe in which the rotating cutting tool for boring a underground pipe without digging were considered in this study. The amount of heat generation due to the friction between the rotating cutter and pipe wall, mixing (low of air and water injected to cool down are the two important factors to design the boring machine Computational fluid dynamics analysis using the Eulerian mixture model and the standard $\kappa-\varepsilon$ turbulence model was used to analyze the complex phenomena in a pipe during the process. Results show that pipe wall temperature decreased with increasing the cooling water inlet velocity. it is also shown that pipe wail temperature was lowered when the cutter rotation speed was increased until 600 rpm. There was no further cooling effect over 600 rpm.