• 한국해양공학회지
• /
• 제10권2호
• /
• pp.88-97
• /
• 1996

The pupose of this study is to improve the mechanical properies and to evaluate the residual stresses of flame-sprayed Alumina ceramic coating layer. The first work in this study is to investigate the effects of strengthening heat treatments on the mechanical properties of coating layer. Strengthening heat treatments for sprayed specimens were carried out in vaccum furnace. The mechanical properties such as microhardness, thermal shock resistance, adhesive strength and erosion resistance were tested for the sprayed specimens after strengthening heat treatments. And it was clear that the mechanical properties of coating layer were much improved by strengthening heat treatments. The second work in this study is to evalute the residual stresses in coating lsyer by numerical analysis. FDM and FEM were used to analyze temperature distribution and residul stresses in coating layer. It was proved that are tensile stresses in coating layer and that residual stresses can be controlled by the appropriate selection of the spraying parameters such as preheat temperature, coating thickness and bond coat thickness.

• 콘크리트학회논문집
• /
• 제16권3호
• /
• pp.293-302
• /
• 2004

국내외의 건설공사에 프리텐션 방식을 이용한 프리스트레스트 콘크리트 구조물이 폭넓게 활용됨에 따라 프리텐션부재 단부에서의 응력전달에 관한 관심이 증가되고 있다. 그러나 전달길이에 대한 현행 기준에서는 프리스트레스 힘의 크기와 PS 강재의 직경만을 고려하고 있으나 프리스트레스를 도입할 때의 콘크리트의 강도 및 피복두께 등의 인자들도 전달길이에 영향을 미치는 것으로 나타나고 있다. 따라서 본 연구에서는 강선의 직경과 유효 프리스트레스의 크기뿐만 아니라 콘크리트의 압축강도와 콘크리트의 피복두께 등이 PSC부재의 전달길이에 미치는 영향을 정량적으로 규명하고, 이로부터 이 영향 인자들을 고려한 합리적인 전달길이 예측식을 제안하였다. 이 식의 제안을 위하여 먼저 강선과 콘크리트 사이의 부착거동에 대한 부착응력-슬립 모델을 실험 자료로부터 도출한 후 이를 계면요소에 도입하여 다양한 설계변수에 대하여 유한요소해석을 실시하여 전달길이를 구하였다. 이로부터 각 변수가 전달길이에 미치는 영향을 분석하고 이를 바탕으로 설계시 사용할 수 있는 전달길이의 예측식을 유도하여 제안하였다. 본 연구에서 제시한 예측식은 보다 실제적이고 정확한 전달길이를 결정하는데 유용하게 사용될 수 있으며 프리텐션 프리스트레스트 콘크리트 부재의 전달길이에 대한 현행 설계기준을 개선하는 데에 유용한 자료를 제공할 것으로 사료된다.

• Geomechanics and Engineering
• /
• 제19권6호
• /
• pp.485-498
• /
• 2019

Pre-tensioned rock bolts can be classified into fully anchored, lengthening anchored and point anchored bolts based on the bond length of the resin or cement mortar inside the borehole. Bolts in varying anchoring methods may significantly affect the supporting effect of surrounding rock around a tunnel. However, thus far, the theoretical basis of selecting a proper anchoring method has not been thoroughly investigated. Based on this problem, 16 schemes were designed while incorporating the effects of anchoring length, pretension, bolt length, and spacing, and a systematic numerical experiment was performed in this paper. The distribution characteristics of the stress field in the surrounding rock, which corresponded to various anchoring scenarios, were obtained. Furthermore, an analytical approach for computing the active and passive strengthening index of the anchored surrounding rock is presented. A new fully anchoring method with pretension and matching technology are also provided. Then, an isolated loading model of the anchored surrounding rock was constructed. The physical simulation test for the bearing capacity of the model was performed with three schemes. Finally, the strengthening mechanism of varying anchoring methods was validated. The research findings in this paper may provide theoretical guidelines for the design and construction of bolting support in tunnels.

• Wind and Structures
• /
• 제37권4호
• /
• pp.289-302
• /
• 2023

Insulating glass units (IGUs) have been widely used in buildings in recent years due to their superior thermal insulation performance. However, because of the panel reciprocating motion and fatigue deterioration of sealants under long-term wind loads, many IGUs have the problem of early failure of watertight properties in real usage. This study aimed to propose a statistical method for wind-induced deflection of IGU panels during the whole life service period, for further precise analysis of the accumulated fatigue damage at the sealed part of the edge bond. By the estimation of the wind occurrence regularity based on wind pressure return period, the events of each wind speed interval during the whole life were obtained for the IGUs at 50m height in Beijing, which are in good agreement with the measured data. Also, the wind-induced deflection analysis method of IGUs based on the formula of airspace coefficient was proposed and verified as an improvement of the original stiffness distribution method with the average relative error compared to the test being about 3% or less. Combining the two methods above, the deformation of the outer and inner panes under wind loads during 30 years was precisely calculated, and the deflection and stress state at selected locations were obtained finally. The results show that the compression displacement at the secondary sealant under the maximum wind pressure is close to 0.3mm (strain 2.5%), and the IGUs are in tens of thousands of times the low amplitude tensile-compression cycle and several times to dozens of times the relatively high amplitude tensile-compression cycle environment. The approach proposed in this paper provides a basis for subsequent studies on the durability of IGUs and the wind-resistant behaviors of curtain wall structures.

• 대한토목학회논문집
• /
• 제14권3호
• /
• pp.403-414
• /
• 1994

본 연구에서는 철근콘크리트 격납구조물에서 가상의 냉각재 유출사고에 의한 온도하중과 압력에 따른 거동을 알아보기 위한 비선형 해석을 수행하였다. 시간에 따른 온도하중을 결정하기 위하여 과도온도해석을 통해 격납구조물 단면내의 온도분포를 구하였다. 구조물은 기하학적 비선형성과 재료비선형성을 고려한 쉘요소로 이상화되며, 쉘요소는 두께방향에 따라 변하는 응력을 고려하기 위해 몇 개의 층으로 이루어진 모델을 사용하였다. 본 연구에서는 재료비선형성을 고려하기위해 콘크리트의 압축거동은 Drucker-Prager 항복규준에 의해 모델링하며 부착효과를 고려한 콘크리트의 인장거동을 나타내기 위해 인장증강모델을 사용하였다. 철근은 축방향력만을 받는 분포 철근층으로 모델링하였으며 steel liner는 Von Mises 항복규준에 따라 모델링하였다. 열응력은 인접한 두시간 단계에서의 온도차를 하중증가로 고려하여 초기변형 문제로 변환하여 결정되었다. 본 연구에서의 수치해석결과에 의하면 과도온도해석에 근거한 비선형온도경사를 고려할때의 응력이 고려하지 않을때의 응력에 비해 크게 나타남을 알 수 있었다. 본 연구는 우리나라에서 많이 건설되고 있는 원자력발전소의 정확하고 진보적인 해석을 위하여 비선형해석 기법을 유도하여 제시하였으며, 특히 온도분포의 비선형성과 재료비선형을 고려한 고급 유한요소해석을 가능케하고 있다.

• Journal of the Korean Wood Science and Technology
• /
• 제15권3호
• /
• pp.44-55
• /
• 1987

In order to study the effect of sawdustboard combined with plastic chips, 0.5mm($T_1$), 1mm($T_2$), 1.4mm($T_3$) thick nylon fiber. polypropylene rope fiber(RP), and 0.23mm thick moth-proof polypropylene net fiber(NP) were cut into 0.5, 1, 2cm long plastic chips. Thereafter, sawdustboard combined with plastic chips prepared as the above and plastic non-combined sawdustboard(control) were manufactured into 3 types of one-, two-, and three layer with 5 or 10% combination level. By the discussions and results at this study, the significant conclusions of mechanical and physical properties were summarized as follows: 1. The MORs were shown in the order of 3 layer> 2 layer> 1 layer among plastic non-combined boards, and $T_3$ < $T_2$ < $T_1$ < RP (NP(5%) < NP(l0%) among plastic combined boards. In 2cm long plastic chip in 1 layer board, the highest strength through all the composition was recognized. 1 layer board showing the lower strength with 0.5cm plastic chip rendered to the bending strength improvement by 2 or 3 layer board composition. On the other hand, 2 or 3 layer combined with 1, 2cm long polypropylene net fiber chips incurred MOR's conspicuous decrease requiring optimum plastic chip combined level and consideration to combined type. 2. MOE in plastic non-combined 3 layer board exhibited sandwich construction effect by higher resin content application to surface layer in the order of 3layer>1layer>2layer with the highest stiffness of the board combined with polypropylene chip, while nylon chip-combined board had little difference from plastic non-combined board. In relevant to length and layer effect, 3 layer board combined with the 0.5cm long polypropylene net fiber chip in 5% and 10% combined level presented 34-43% and 44-76% stiffness increase against plastic non-combined board(control), respectively. Moreover, in 1 layer board, 30% stiffness increase with 10% against 5% combined level in the 1 and 2cm long polypropylene net fiber chip was obtained. 3. Stress at proportional limit(Spl) showing the fiber relationship (r: 0.81-0.97) between MOR presented in the order of 1 layer<2 layer<3 layer in plastic non-combined board. Correspondingly, combined effect by layer and plastic chip length was similar to MOR's. 4. Differently from previous properties(MOR, MOE, Spl). work to maximum load(Wml) of 2 layer board approached to that of 3 layer board. Conforming the above phenomenon. 2 layer combined with 0.5cm long polypropylene net fiber chip kept the greater work than 1 layer. The polypropylene combined board superior to nylon -and plastic non - combined board seemed to have greater anti - failing capacity. 5. Internal bond strength(IB), in contrast to MOR's tendency. showed in the order of T1