• 한국가스학회지
• /
• 제25권1호
• /
• pp.7-13
• /
• 2021

재액화 드럼은 과냉각된 LNG를 증발가스에 직접 분사하기 위해 상부에 스프레이 노즐을 설치하고, 기액 분리가 용이하도록 데미스터를 설치한 제품으로, 소형 재액화 설비의 재액화 효율을 높이기 위해 개발한 제품이다. 드럼의 상온 내압기밀시험에서는 설계압력의 1.5배 이상의 압력에서도 누설(Leak)이 없었으나, 단열성능시험 중 온도변화에 따른 수축/팽창으로 인해 볼트풀림 현상이 발생하였다. 제품의 지속적인 사용을 위해 플랜지 결합부의 단열 시공은 탈부착이 가능하도록 개발하였으며, 기존 단열과의 열침입량 비교 결과 드럼 내 유입 유량 대비 매우 미미함을 확인하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제26권3호
• /
• pp.48-52
• /
• 1998

Residues such as walnut, pinenut and peanut shells were used as a filler in adhesive for bonding radiata pine plywood. The nutshell residues were prepared by simply drying to 8% moisture content and grinding the dry material using a laboratory Wiley mill with a $75{\mu}m$ (200 mesh) screen. The nutshells residues were compared to a commercial filler commonly used in adhesives by the structural plywood and laminated veneer lumber industry in the United States. The adhesive mixes were made by following the recommended procedure of Georgia-Pacific Resins, Inc., using phenol-formaldehyde resin. For each filler type, three-ply plywoods, 6 mm nominal thickness and 30 by 30 cm in size, were fabricated at two press times (4 and 5 min) and around 30 minute assembly time. Evaluations of the nutshell residues were carried out by tension shear tests after cyclic boil tests on plywood. The results of the performance test included tension shear strength and wood failure. All plywoods made with the nutshell fillers were comparable to those made with the control filler. These results indicate that nutshell residues would be suitable as filler for plywood adhesives.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.365-370
• /
• 2005

Infrared (lR) detectors are widely used for such applications as thermoelstic stress analysis, medical diagnostics and temperature measurement. Infrared detectors commonly need to be refrigerated below 80 K, and thus a cooling system should be equipped together with the detector system. The cooling load, which should be removed by the cooling system to maintain the nominal operating temperature of the detector, critically depends on the insulation efficiency of the cryochamber housing the detector. Cryochamber considers the conduction heat transfer through a cold finger, the gases conduction and radiation heat transfer. The thermal loads of an infrared detector Cryochamber with radiation shield are investigated experimentally in present study. Since the effect of radiation heat transfer on thermal loads is significant, radiation shields is installed in the cold finger part to protect heat input through radiation. It is found that the thermal load can be substantially reduced by increasing the number of radiation shield.

• 한국지반공학회지:지반
• /
• 제11권2호
• /
• pp.79-98
• /
• 1995

본 연구에서는 nailed-soil 굴착벽체의 거동특성 분석결과를 토대로, 벽체의 움직임 정도에 따라 네일-주변홀 사이에서 발휘되는 전단강도 예측을 위한 해석적 모델링이 이루어졌다. 또한 제시된 발휘전단강도 예측모델을 토대로, nailed-soil굴착벽체의 전체적인 안정성 평가를 위한 한계평형해석법이 Morgenstern-Price 절편법을 응용하여 제시되었다. 본 연구 제시 모델 및 해석법은, 굴착단계별로 또한 최종굴착시공 완료직후 및 장기적인 측면에서, nailed -soil굴착벽체의 거동예측이 가능하며 이에 대한 적합성 검토를 위해, 지반조건 등이 서로 다른 3개의 nailed-soil 실험벽체에 대해 제시된 설치네 일의 발휘인장력 측정결과 및 전체안정성 평가결과 등을 본 연구의 예측치와 비교.분석하였다. 본 연구 해석법에는 지반내부에 존재할 수 있는 침투수압의 영향이 포함되었다.

• 설비공학논문집
• /
• 제20권1호
• /
• pp.11-16
• /
• 2008

Infrared (IR) detectors are widely used for such applications as thermoelastic stress analysis, medical diagnostics and temperature measurement. Infrared detectors commonly need to be refrigerated below 80 K, and thus a cooling system should be equipped together with the detector system. The cooling load, which should be removed by the cooling system to maintain the nominal operating temperature of the detector, critically depends on the insulation efficiency of the cryochamber housing the detector. Thermal load of a cryochamber is attributed to the conduction heat transfer through a cold finger, the gases conduction and radiation heat transfer. The thermal loads of an infrared detector cryochamber with a radiation shield are investigated experimentally in present study. Since the effect of radiation heat transfer on thermal loads is significant, radiation shields is installed in the cold finger part to protect heat input through radiation.

• 대한조선학회논문집
• /
• 제56권6호
• /
• pp.515-522
• /
• 2019

Since Liquefied Natural Gas (LNG) is normally carried at 1.1 bar pressure and at -163℃, special Cargo Containment System (CCS) are used. As LNG carrier is becoming larger, typical LNG insulation systems adopt a method to increase the thickness of insulation panel to reduce sloshing load and Boil-off Rate (BOR). However, this will decrease LNG cargo volume and increase insulation material costs. In this paper, silica aerogel, glass bubble were synthesized in polyurethane foam to increase volumetric efficiency by improving mechanical and thermal performance of insulation. In order to increase dispersibility of particles, ultrasonic dispersion was used. Dynamic impact test, quasi-static compression test at room temperature (20℃) and cryogenic temperature (-163℃) was evaluated. To evaluate the thermal performance, the thermal conductivity at room temperature (20℃) was measured. As a result, specimens without ultrasonic dispersion have a little effect on strength under the compressive load, although they show high mechanical performance under the impact load. In contrast, specimens with ultrasonic dispersion have significantly increased impact strength and compressive strength. Recently, as the density of Polyurethane foam (PUF) has been increasing, these results can be a method for improving the mechanical and thermal performance of insulation panel.

• Journal of the Korean Wood Science and Technology
• /
• 제39권6호
• /
• pp.498-504
• /
• 2011

The purpose of this study was to investigate and develop an eco-frendly wood adhesive based on vegetable oil (especially soybean oil), the renewable and sustainable natural resources, using ozonification technology for the chemical structure modification. The waste soybean oil (WSBO) was reacted with $O_3$ at the rate of $450m{\ell}$(acetone) : $50m{\ell}$ (WSBO) for different times, 1, 2, 3 hrs. The investigation of the modified chemical strecture of the ozonied WSBOs were conducted using FT-IR. As ozonification time increased, the peak of the unsaturated double bonds was disappeared especially ozonized-3hrs and aldehyde or carboxyl peak appeared because ozonification broke the oil into small molecules. The plywood were made at $150^{\circ}C$ with 4 minutes hot-press time using the different ozonized 3 hrs WSBO/pMDI adhesives and were tested for the dry, wet, cyclic boil test according to the Korea Industrial Standard F3101 Ordinary plywood. The bond strengths gradually increased until 1 : 0.5~1 : 3, but it decreased 1 : 4, as the contents of pMDI increased. The results of the dry, wet and cyclic bond strengths the equivalent ratio was formed approximately between 1 : 2~1 : 3. And the 1 : 1~1 : 4 strengths met constantly the standard requirement of 7.0kgf/$cm^2$ (KS F3101). From the comprehensive view on the results of above experiment, it could be confirmed that ozonized WSBO/pMDI has characteristics of effective reactivity and wet stability showed as an excellent candidate of wood adhesive applications.

• 기술사
• /
• 제19권4호
• /
• pp.22-29
• /
• 1986

1) The recipe for tea is to mix tea leaves or tea buds with odorous pharmaceuctial materials, which are boiled and drunk, addition of honey only to that odorous pharmaceutical meterials without adding tea buds to that can be used. 2) Viewed from the part of tea plant the fruit of it accoupies most. The cereal does as much. 3) what we have referred to from the records on this subject are "Guogapylyong" which is of the yuan dynasty and "Jeungbo-Salymkeongje" which is of the Yi dynasty, based on which no trace of pure tea can be found but odorous pharmaceutical kinds of tea only were widely spread. 4) The characteristics of tea are to help make stomach strong, mind cleared, the lungs copious, counteract, and quench thirstiness. The tea help build liver as well as bring about health. 5) As a result of sense test, those kinds of tea were much better than contemporary kinds of teas as far as flovor and sweetness are concerned. Those teas had complex tastes, while teas of to day have simple one. 6) Because the history not so clear before the periods of Unified Sila that the recordings of teas are rare, we can hardly know about tea. Our ancestors really began to drink teas from the period of Unified Sila on. This country turning to the Koryo dynasty, tea drinking manner began to prevail so much that drinking tea became a ceremony. Daring the Yi dynasty it was much camplicated to make and boil the leaf tea. As a result of the previous fact pure tea came to have disappeared and odorous pharmaceutical became prevailent. 7) For value of exploiting Kungjuk tea (ginger tea seasoned with phyllostachy and addition of honeyl) was the highest among many. The worth of developing all the teas among all the beverages was regarded as that high of 51%, while even the tea regarded as worthless obtained 4％ of support, which is the lowest.

• Journal of the Korean Wood Science and Technology
• /
• 제37권1호
• /
• pp.56-64
• /
• 2009

본 연구의 목적은 콩기름을 오존 산화 처리하여 기능기를 도입하고 이를 바탕으로 친환경 목재 접착제를 개발하는 것이다. 시판용 콩기름을 시간당 약 7.13 g의 오존을 발생시켜 15분, 30분, 60분, 120분간 오존산화 처리한 후 FT-IR, $^1H$-NMR, MALDI-TOF MS, GC/MS 측정하여 구조변화를 분석하였다. 기기분석 결과 오존산화처리에 의하여 콩기름의 불포화 이중결합이 개열되어 카르복실기 또는 알데하이드기가 생성됨을 확인하였다. 오존산화콩기름 변성 pMDI 접착제의 접착력은 오존처리 정도와 pMDI의 혼합비율에 따라 달라지며, KS F 3101 보통합판기준 내수 접착강도를 안정적으로 만족 시키는 조건은 오존산화 처리시간 30분~60분, pMDI와 1:1로 혼합한 경우이며, 준내수 접착강도를 만족시키는 범위는 오존산화 처리시간 30분~60분, pMDI의 혼합비 0.5이상, 상태접착강도를 만족시키는 범위는 오존산화 처리시간 15분~60분, pMDI의 혼합비 0.25 이상임을 알 수 있었다. 위의 실험결과를 종합하여 볼 때, 오존산화 처리한 식용유는 오존처리시간 및 pMDI의 혼합비율을 조절하면 상태접착력 뿐만 아니라 내수접착력이 요구되는 목질복합재료 제조용 접착제 제조가 가능함을 확인할 수 있었다.

• 한국지반공학회지:지반
• /
• 제13권5호
• /
• pp.75-88
• /
• 1997

본 연구에서는 항타말뚝과 비교한 현장타설말뚝의 극한지지력을 하중전이함수를 적용하여 예측하였으며 이를 토대로 항타말뚝과 비교한 현장타설말뚝의 지지력을 현장재하시험 결과와 비교, 분석하였다. 비교, 분석은 하중전이함수들 중 응력 연화를 고려한 방법, 쌍곡선 함수법 및 탄소성 방법을 대표하는 Vijayvergiya의 방법, Castelli의 방법 및 2중 직선법을 적용하여 지반 종류에 따라 현장타설말뚝의 하중-변위관계를 산정하였다. 본 연구 결과 동일한 지반에 설치된 항타말뚝과 현장타설말뚝의 극한지지력은 총 주면마찰력의 차이로 인하여 항타말뚝이 더 큰 것으로 나타났으며 이러한 차이는 점토질 지반에서 보다는 모래질 지반에서 더 크게 나타났다. 같은 지지력을 발현하기 위해 필요한 말뚝 두부에서의 변위량은 항타말뚝보다는 현장타설말뚝에서 더 크게 나타났으며 현장타설말뚝이 극한지지력을 발현하기 위해 필요한 변위량과 이와 같은 크기의 지지력을 발현하는데 필요한 항타말뚝의 변위량과의 차이는 모래질 지반에서 가장 크게 나타났다. 현장타설말뚝과 항타말뚝의 말뚝직경과 길이의 비(LID)의 변화에 따른 극한지지력의 차이는 점토질 지반의 경우 일정한 것으로 나타났으나 모래질 지반에서는 LID의 비가 증가할수록 극한지지력의 차이가 증가하는 것으로 나타났다.