• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.26-32
• /
• 2017

This paper presents a low power and high resolution incremental delta-sigma ADC that utilizes a passive integrator instead of an opamp-based active integrator. Opamp is a power-hungry block that involves tight design tradeoffs. To avoid the use of active integrator, the s-domain characteristic of an active integrator is first analyzed. Based on the analysis, an active integrator with low gain design is proposed as an alternative design method. To save power even more aggressively, a passive integrator with no static current is proposed. A 1st order single-bit incremental delta-sigma ADC using the proposed passive integrator is implemented in a 65nm CMOS process. Transistor-level simulation shows that the ADC consumes only 0.6uW under 1.2V supply while achieving SNDR of 71dB with 22kHz bandwidth. The estimated total power consumption including digital filter is 6.25uW, and resulting power efficiency is on a par with state-of-the-art A/D converters.

• Journal of Environmental Health Sciences
• /
• v.33 no.4
• /
• pp.276-282
• /
• 2007

The purpose of this study is to assess the accurate state of the following: total welding fumes versus welding fumes in the air, respirable particulate mass, and exposure of dockyard welders to heavy metals. In addition, this study provides basic data for proposing improvements to create efficient and appropriate welding environments and to prevent occupational diseases. The subjects of this study were 94 laborers who worked at the block construction sites of large-scale dockyards located in Gyeongnam Province from March 2005 to June 2005. In order to collect samples on total welding fumes in the air and respirable particulate mass from the welders, Methods 0500 and 0600, established by the National Institute for Occupational Safety and Health (NIOSH), were used. The metals within the welding fumes were also analyzed using Inductively Coupled Plasma (ICP) under Method 7300 from NIOSH. The results of this research are summarized below. The geometric mean concentration of total welding fumes and that of respirable particulate mass were $4.11\;mg/m^3\;and\;3.53\;mg/m^3$, respectively. As a result of comparing the two measurement methods, there were significant differences (p<0.05) between the two groups for Ca, Cu, Cr, and Ni; however, there were no differences in Fe, Mg, Zn, Mg, Pb, and Cd. As a result of the analysis, the correlation between Mn and the concentration of heavy metals in the total welding fumes and respirable particulate mass was found to be -0.29, a significant negative correlation. The correlation between other heavy metals, however, was low. Finally, in the same total welding fumes, the correlation of Fe and Mg was high.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.6
• /
• pp.2014-2034
• /
• 2015

This paper focuses on solving co-channel interference (CCI) issues arising in the open subscriber group (OSG) mode of heterogeneous networks (HetNets). Considering a general framework consisting of arbitrary number of picocells within a macro cell, where the inter-user interference (IUI) is the main CCI to macro user equipments (UEs), while the the inter-cell interference (ICI) is the major CCI to pico UEs. In this paper, three IA based transceiver design schemes are proposed. For macro cell, we uniformly use block diagonalization (BD) scheme to eliminate the IUI. And for picocells, three IA schemes are proposed to mitigate the ICI. The first scheme, named as zero forcing IA (ZF-IA) scheme, aligns the inter picocell interference onto an arbitrary sub-space of the cross-tier interference using ZF scheme. Considering the channel state information (CSI) of the desired channel of pico UEs, the second scheme, named as optimal desired sub-channel selected IA (ODC-IA) scheme, aligns the inter picocell interference onto a certain sub-space of the cross-tier interference, which guarantees the largest channel gain of the desired signal of pico UEs. The third IA scheme, named as maximum cross-tier interference selected IA (MI-IA) scheme, is designed for the system with less receive antennas. The inter picocell interference is aligned onto the space of the strongest cross-tier interference and only the interference on this space is nullified. The complexity analysis and simulations show that the proposed transceiver design schemes outperform the existing IA schemes in the OSG mode of HetNets, and the MI-IA scheme reduces the requirement of the receive antennas number with lower complexity.

• Geotechnical Engineering
• /
• v.11 no.1
• /
• pp.41-50
• /
• 1995

In situ clay soils with Ko condition have anisotropic characteristics, varying the response according to the principal stress direction upon loading. But because of their practicality and simplicity, consolidated isotropic undrained compression tests are commonly used in practice to determine the behavior of cohesive soils. In this study to investigate the anisotropic characteristics and the effects of consolidation stress states on the response of normally consolidated clay soils during shearing, triaxial compression and extension tests after consolidating the undisturbed clay soil samples, which are obtained as a block sample to normalized consolidation states under isotropic or Ko state, were carried out. As a result of tests, the anisotropy of the undrained strength was confirmed. Comparing the soil responses between isotropic and Ko consolidation, the undrained strength by isotropic consolidation is overestimated because of its higher mean consolidation pressure. And isotropic consolidation reduces the anisotropy of soil response and influences on the stress-strain behavior and pore pressure response because the animotropic soil structure is partially collapsed during isotropic consolidation process. Also, OCR in overconsolidated soils is decreased by isotropic consolidatiorL Friction angle in eztension is higher than that in compression, but regression analysis shows that friction angle with cohesion in extension is almost the same as that without cohesion in compresslon.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.660-665
• /
• 2006

This paper presents a finite element method to analyze the free and forced vibration of a hard disk drive (HDD) considering the flexibility of a spinning disk-spindle with fluid dynamic bearings (FDBs), an actuator with pivot bearings, an air bearing between head-disk interface and the base with complicated geometry. Finite element equation of each component is consistently derived with the satisfaction of the geometric compatibility of the internal boundary between each component. The spinning disk, hub and FDBs are modeled by annular sector elements, beam elements and stiffness and damping elements, respectively. The actuator am, E-block, suspension and base plate are modeled by tetrahedral elements. The pivot bearing in the actuator and the air bearing between head-disk interfaces are modeled by the stiffness element with five degrees of freedom and the axial stiffness, respectively. A global matrix equation obtained by assembling the finite element equations of each substructure is transformed to a state-space matrix-vector equation, and both damped natural frequencies and modal damping ratios are calculated by solving the associated eigenvalue problem with the restarted Arnoldi iteration method. Modal and shock testing are performed to show that the proposed method well predicts the vibration characteristics of a HDD.

• Journal of Embryo Transfer
• /
• v.24 no.1
• /
• pp.65-69
• /
• 2009

The aim of the present study was to investigate the cleavage pattern, its developmental ability and apoptosis of porcine embryo in vitro. Morphology data on a total of 919 embryos were analyzed retrospectively. Forty-eight hours after insemination, embryos were classified into five groups based on the cleavage state as follows; 1 cell, 2 cell, 4 cell, 5 to 8 cell and fragmentation. These groups were cultured another 120 hours and then evaluated for blastocyst formation. Blastocyst formation rates were significantly higher in 4 cell (42.5%) and 5 to 8 cell (48.6%) cleaving groups than in other groups (p<0.05). On the other hand, 2 cell and fragmentation groups produced 4.9% and 3,9% blastocysts, respectively. And we could verify that in the event of 2 cell block and fragmentation of embryo. To analyze the apoptotic frequency in preimplantation development of porcine IVF embryos, all cells of each blastocyst were performed by TUNEL assay. There were no significantly differences in the total cell numbers of embryos and apoptotic cell rate in blastocysts among the each classified groups. Data suggest that 4 cell and 5 to 8 cell cleaving embryos at 48 hour after insemination have high developmental competence, and may be an useful parameter to predict the development of preimplantation embryos and to study using preimplanation embryonic research.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.22 no.4
• /
• pp.709-717
• /
• 2012

The round reduction on block cipher is a fault injection attack in which an attacker inserts temporary errors in cryptographic devices and extracts a secret key by reducing the number of operational round. In this paper, we proposed an improved round reduction method to retrieve master keys by injecting a fault during operation of loop statement in the Triple DES. Using laser fault injection experiment, we also verified that the proposed attack could be applied to a pure microprocessor ATmega 128 chip in which the Triple DES algorithm was implemented. Compared with previous attack method which is required 9 faulty-correct cipher text pairs and some exhaustive searches, the proposed one could extract three 56-bit secret keys with just 5 faulty cipher texts.

• Journal of Digital Convergence
• /
• v.20 no.3
• /
• pp.343-348
• /
• 2022

Recently, With the recent rapid development of technology, the amount of data generated by various systems is increasing, and enterprise servers and data centers that have to handle large amounts of big data need to apply high-stability and high-performance storage devices even if costs increase. In such systems, SSD(solid state disk) that provide high performance of read/write are often used as storage devices. However, due to the characteristics of reading and writing on a page-by-page basis, erasing operations on a block basis, and erassing-before-writing, there is a problem that performance is degraded when duplicate writes occur. Therefore, in order to delay this performance degradation problem, over-provision technology of SSD has been applied internally. However, since over-provided technologies have the disadvantage of consuming a lot of storage space instead of performance, the application of inefficient technologies above the right performance has a problem of over-costing. In this paper, we proposed a method of measuring the performance and cost incurred when various over-provisions are applied in an SSD and predicting the system-optimized over-provided ratio based on this. Through this research, we expect to find a trade-off with costs to meet the performance requirements in systems that process big data.

• Journal of the Korean Geosynthetics Society
• /
• v.4 no.3
• /
• pp.35-43
• /
• 2005

The geosynthetic reinforced segmental retaining walls(SRW) are improved that the disadvantage of existed retaining wall and the workability in field. Recently, the segmental retaining wall is replacing the exited wall because it is quickly advanced to using by the block in-situ. The use, therefore, is increasing. But, the trends of the large scaled construction was developed that the problems likely to crack and collapse, those are caused of careless in design and construction of SRW not considering about various surrounding conditions. In this study, the cause analysis on destructed SRW was carried out that based on the datum of measured displacement of walls, rainfall features and ground sounding conditions. Also, the analysis of the global slope stability was carried out on collapsed section and non-collapsed section using critical equilibrium method. For the rational stability and analysis of slope including SRW structure, the site conditions including situations of topography, ground and histories of construction and collapse etc should be considered. The rational countermeasure methods for non-collapsed and collapsed areas may be sustained as much as possible current state.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.34 no.12
• /
• pp.65-76
• /
• 2018

Due to the rapid demographic and structural changes, Korea has faced a variety of social issues and quickly entered the aged society since the 2000s. In order deal with this reality, diverse types of welfare policies are emerging in the society as a whole. The government began to supply domestic public silver housing in 2016 to provide against the quickly growing aged society and now, the government is planning to supply approximately 50,000 housing by 2022 for quantitative growth of aged society, by selecting 1st and 2nd designated areas for the project additionally. This public retirement(silver) housing combines 'space' with 'service'. The lower floors are a public silver welfare Facilities and the upper floors are a housing spaces. This type of housing is to deal with requirements of rental housing residents by combining physical space with supporting service. Based on barrier-free design, the complex and unit house have safety handles and alarm bells in the bathroom, undulating washstands, bathroom sliding doors, corridor safety handles, and emergency safety exit lamps in each housing unit so the aged and the disabled can use easily and conveniently. Also, hand rails are installed and stepped pulleys are removed to promote convenience. Currently, the government is planning to increase the supply, focusing on low-income groups, such as beneficiaries of national basic livelihood and the working poor. Recognizing that the public retirement(silver) housing project is at its early stage, this study examined satisfaction, based on evaluations of real residents. This study aimed to obtain more empirical research data and apply them to public retirement(silver) house space analysis. For analysis, this study targeted Wirye public retirement(silver) housing and Magnolia public retirement(silver) housing that are in operation, and literature review, previous research review, and field survey were conducted to examine the present state. Using the questionnaires consisting of four large classification items; Block Layout, Housing Unit, Welfare Facilities, and Barrier-free Design, and sub-details, a survey was conducted to analyze residents' satisfaction. In conclusion, it is anticipated that this study would serve as basic research data about public retirement(silver) housing to increase continuously in future by analyzing public retirement(silver) housing spaces, on the basis of the analyzed data.