• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.82-89
• /
• 2009

In order to investigate the spray characteristics according to diesel and bioethanol blending with biodiesel fuel, macroscopic spray characteristics were analyzed from the comparison of the effect of the injection pressure, ambient pressure and density on the spray tip penetration and spray cone angle. In addition, spray atomization characteristics were studied with local and overall Sauter mean diameter (SMD) and the contour map of SMD distribution at various injection conditions. It was revealed that the spray tip penetration of biodiesel fuels blended with diesel and ethanol was shorter than that of an undiluted biodiesel fuel at low injection pressure. However, the difference of spray tip penetration among three test fuels reduces at a high injection pressure. Increase of the ambient gas density leads to the decrease of the spray tip penetration of three test fuels. When diesel and ethanol fuels add to an undiluted biodiesel fuel, spray cone angle increases due to the decrease of the fuel density at the same ambient pressure condition. On the other hand, the droplet mean diameter decreases due to the reduction of the kinematic viscosity and surface tension.

• Journal of Power System Engineering
• /
• v.18 no.2
• /
• pp.5-11
• /
• 2014

The purpose of this study is to investigate the specific characteristics of combustion and exhaust emissions on a 4-cylinder common rail diesel engine as EGR rate and the rate of blended bio-diesel was altered. Bio-diesel fuel which is a sort of alternative fuels can be adapted to diesel engine directly without modifying. This study was performed to 2000rpm of engine speed with torque 30Nm while EGR rate and the rate of blended bio-diesel was changed. Decreasing combustion pressure and increasing the rate of heat were occurred when we had changed the EGR rate on the 20% of bio-diesel blended diesel fuel. The maximum pressure of combustion and the IMEP became higher as the EGR rate and the rate of blended bio-diesel were changed. Exhaust gas temperature was increased the higher rate of the blended bio-diesel under the fixed EGR rate. However, it went down as the EGR rate increased. The amounts of CO and Soot were reduced with increasing the rate of the blended bio-diesel without changing EGR rate and raised with increasing of the EGR rate. On the fixed EGR rate, NOx was increased along with growing the rate of the bio-diesel. On the other hand, it was decreased while EGR rate were going up.

• Journal of Energy Engineering
• /
• v.13 no.1
• /
• pp.20-27
• /
• 2004

In the study, the effect of low boiling point oxygenates in high viscous fuels on the exhaust emissions has been investigated for a single cylinder DI diesel engine. It was tested to estimated change of engine performance and exhaust emission characteristics for the base fuels and low boiling point oxygenates blended fuel which have six kinds of fuels and various mixed rates. The results of the study may be con eluded as follows By blending of various low boiling point oxygenated agents to lower grade fuels, significant improvements were simultaneously obtained in smoke, CO, PM, SOF and BSEC. Especially, these trends were remarkably obtained by retarding injection timing, by decreasing boiling point and increasing blending contents of additives in case of oxygenated agents rather than non-oxygenated agents. Also, it was revealed that when 20 vol.％ DMM added to high viscosity fuels and injection timing was retarded, Nox-smoke trade off relationship was much better than that of ordinary diesel fuel. Thus, lower grade fuels with high viscosity could be expected to be used efficiently and cleanly in diesel operation by blending low boiling point oxygenates.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.3
• /
• pp.85-93
• /
• 1994

The engine performance and combustion characteristics of diesel oil and fish oil blended with diesel oils were investigated at various blending rate of fish oil in a diesel engine. The maximum pressure showed no significant difference among test fuels at low load, but it was higher as the blending rate of fish oil increases at high load. Increasing the blending rate of fish oil, the rate of heat release and burned fraction were higher than those of diesel oil. The ignition delay became longer than that of diesel oil as the blending rate of fish oil increases, and its differences were larger at different loads. The combustion duration and density of smoke were shorter and lower as the blending rate of fish oil increases. The rate of fuel consumption showed no significant difference between diesel oil and fish blended with diesel oils.

• Journal of ILASS-Korea
• /
• v.13 no.1
• /
• pp.51-57
• /
• 2008

The objective of this study was to investigate the spray characteristics of commercial biodiesel fuel at various fuel injection conditions. To examine the effect of various factors on the development of a biodiesel sprays, experiments were conducted at the various injection pressures, ambient pressures and blending ratio of bio-diesel fuels. As a result of experimental study, it was shown that the increase of blending ratio of biodiesel had little influence on spray behaviors under applied fuel injection condition in this study. Because macroscopic characteristics of biodiesel-blended diesel fuel were almost same as that of petrodiesel fuels, it was found that the commercial biodisel is applicable to conventional diesel engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.55-62
• /
• 2009

As an experiment investigation, the effects of ethanol blended gasoline fuel with different injection method on nano-sized particle emission characteristics were examined in a 0.5L spark-ignited single-cylinder engine with a compression ratio of 10. Because this engine nano-particles are currently attracting interest due to its adverse health effects and their impact on the environments. So a pure gasoline and an ethanol blended gasoline fuels, namely E85 fuel, used for this study. And, as a particle measuring instrument, a fast-response particle spectrometer (DMS 500) with heated sample line was used for continuous measurement of the particle size and number distribution in the size range of 5 to 1000nm (aerodynamic diameter). As this research results, we found that the effect of ethanol blending gasoline caused drastic decrease of nano-particle emissions when port fuel injection was used for making better air-fuel mixture than direct fuel injection. Also injection timing, specially direct fuel injection, could be a dominant factor in controlling the exhaust particle emissions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.791-796
• /
• 2017

In this study, the combustion characteristics of paraffin blended fuel on aluminum particle size were investigated. The combustion experiments were carried out using aluminum particles with an average particle size of 100 nm and $8{\mu}m$ and microcrystalline paraffin wax (Sasol 0907). A series of comparison was conducted on the regression rate, the pressure curve and the characteristic velocity of pure paraffin and paraffin blended fuels with aluminum particles. It was found that the micro-sized particles enhance the regression rate as the oxidizer mass flux increased. However, the nano-sized particles decrease the regression rate as the oxidizer mass flux is increased.

• Elastomers and Composites
• /
• v.40 no.2
• /
• pp.104-111
• /
• 2005

Virgin fluororubber(FKM) that is one of the highly-functionalized and expensive special rubber, and recycled FKM that is crushed by high temperature shear-crushing technique from recycled FKM were blended with the various mixing ratio to rubber blends. The cure characteristics and physical properties of these blended rubber compounds were investigated with various contents of recycled FKM and physical properties fur heat and fuels were also measured. Recycled FKM which is prepared by high temperature shear-crushing technique were blended to virgin FKM with the range of $0{\sim}50$ phr. The physical properties indicated that the rubber blend of recycled FKM with 30 phr turned out to be the best compound showing good dispersibility, heat resistance and fuel resistance and inexpensive in price.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.31-43
• /
• 1989

The paper shows a solution by giving vegetable oil a chemical treatment, i.e., transesterification of the rapeseed oil without any modification of the diesel engine for reducing carbon deposits, and to evaluate rate of combustion with vegetable oils, their esterified fuel and their blend fuels using a double Wiebe's function approximation in a naturally aspired D.I. diesel engine. Since any oil will be as material for ester, if it is fatty acid, the sardine oil was considered. In the experiment, engine performance, exhaust gas emissions, and combustion characteristics were measured and calculated for a number of fuels: rapeseed oil, palm oil, ester of rapeseed oil, and these fuels blended with ethanol or diesel fuel.

• Environmental Engineering Research
• /
• v.23 no.3
• /
• pp.242-249
• /
• 2018

The use of palm oil and diesel blended with ethanol, known as a microemulsion biofuel, is gaining attention as an attractive renewable fuel for engines that may serve as a replacement for fossil-based fuels. The microemulsion biofuels can be formulated from the mixture of palm oil and diesel as the oil phase; ethanol as the polar phase; methyl oleate as the surfactant; alkanols as the cosurfactants. This study investigates the influence of the three cosurfactants on fuel consumption and exhaust gas emissions in a direct-injection (DI) diesel engine. The microemulsion biofuels along with neat diesel fuel, palm oil-diesel blends, and biodiesel-diesel blends were tested in a DI diesel engine at two engine loads without engine modification. The formulated microemulsion biofuels increased fuel consumption and gradually reduced the nitrogen oxides ($NO_x$) emissions and exhaust gas temperature; however, there was no significant difference in their carbon monoxide (CO) emissions when compared to those of diesel. Varying the carbon chain length of the cosurfactant demonstrated that the octanol-microemulsion fuel emitted lower CO and $NO_x$ emissions than the butanol- and decanol-microemulsion fuels. Thus, the microemulsion biofuels demonstrated competitive advantages as potential fuels for diesel engines because they reduced exhaust emissions.