• 한국재료학회지
• /
• 제27권2호
• /
• pp.63-68
• /
• 2017

A black nickel oxide powder, one of the commercial nickel oxide ores, was reduced by hydrogen gas in a batch-type fluidized-bed reactor in a temperature range of 350 to $500^{\circ}C$ and in a residence time range of 5 to 120 min. The hydrogen reduction behavior of the black nickel oxide was found to be somewhat different from that of green nickel oxide ore. For the black nickel oxide, the maximum temperature (below which nickel oxide particles can be reduced without any agglomeration) was significantly lower than that observed for the green nickel oxide. In addition, the best curve fittings of the Avrami model were obtained at higher values of the overall rate constant "k" and at lower values of the exponent "m", compared to those values for the green nickel oxide. It may be inferred from these results that the hydrogen reduction rate of the black nickel oxide is faster than that of the green nickel oxide in the early stages, but the situation reverses in the later stages. For the black nickel oxide ore, in spite of the low temperature sintering, it was possible to achieve a high degree fluidized-bed reduction at lower temperatures and at lower gas consumption rates than was possible for the green nickel oxide. In this regard, the use of black nickel oxide is expected to yield a benefit if its ore price is sufficiently lower than that of the green nickel oxide.

• 대한화장품학회지
• /
• 제46권4호
• /
• pp.319-327
• /
• 2020

미세먼지(Particulate matter, PM)는 피부 장벽의 기능을 저하시키고 염증성 피부 질환 및 외인성 노화를 유발하는 대기 오염원이다. 본 연구에서는 대체 미세먼지로서 iron oxide black을 이용하여 화장품에 의한 미세먼지의 피부 부착 방지효과를 평가하였다. 미세먼지 부유챔버는 피부노출부위, 미세먼지 주입구, 부유동력장치, 배출구로 구성하여 미세먼지가 챔버내에서 부유 중 피부에 자연스럽게 부착될 수 있도록 제작하였다. 대체 미세먼지의 부유농도에 따른 피부 밝기 변화를 확인하여 최적의 부유농도 조건을 확인하였다. Iron oxide black의 피부부착 전·후의 밝기차이 (미세먼지 부착 전 밝기 - 미세먼지 부착 후 밝기, Δ)는 미세먼지의 양에 비례한다. 또한, 화장품 5종에 대하여 각각 20명의 피험자를 대상으로 제품 도포군과 무도포 대조군으로 나누어 부유 대체 미세먼지에 대한 피부부착 방지효과를 확인하였다. 피부에 부착된 iron oxide black의 전·후 밝기 차이를 계산하여 대조군과 비교분석하였다(p < 0.05). 시험에 최소 150 mg 이상의 iron oxide black을 사용할 때 농도에 따른 피부 밝기 변화 양상이 뚜렷하게 나타났다. 최적의 부유농도에서 피부와 대체미세먼지의 밝기 간섭이 적고 피부 부착 패턴이 선명하게 나타났다. 5종의 화장품을 피부에 도포할 경우 iron oxide black의 부착양이 대조군에 비해 통계적으로 유의하게 낮았다. 이는 제품에 따라 iron oxide black의 부착을 방지 함을 의미한다. 본 연구는 대체 미세먼지로서 iron oxide black의 피부 부착양상을 확인하고, 화장품에 의한 부착 방지효과를 평가하는 안전하고 유용한 방법이다. 화장품의 다양한 제형이나 원료의 특성에 따라 미세먼지가 피부에 부착되는 것을 방지할수 있음을 확인하였다.

• 한국결정성장학회지
• /
• 제30권4호
• /
• pp.156-161
• /
• 2020

최근에 들어 구조재의 미관에 대한 수요가 증대되고 있어, 색상발현이 우수한 컬러 시멘트 콘크리트 개발이 요구되고 있다. 본 연구에서는 착색제로 사용된 카본블랙과 산화철의 혼입률 변화에 따른 모르타르의 기초물성과 자외선 촉진 내후성 환경에서의 색상발현 유지 특성을 분석하고자 하였다. 실험결과 카본블랙과 산화철을 사용함에 따라 OPC에 비해 초기 플로우는 6.3~17.2 %, 공기량은 3.5~31.5 % 감소되고 단위용적질량는 3.4~5.5 % 증가하는 것으로 나타났다. 그리고 산화철을 혼입함으로 인해 자기 건조수축량도 증가되어 작업성에 유의해야 할 것을 판단된다. 검정색상을 나타내는 명도 L^⁎ 값은 카본블랙 3 %, 산화철 5%를 혼입한 경우가 가장 우수한 검정색상을 보였다. 자외선 촉진 내후성 시험에 의해 L^⁎는 4.28~11.97 % 증가되었고, 카본블랙을 사용함으로 인해 자외선에 의한 색상변화가 적게 되는 것으로 나타났다. 착색 측면에서 최적배합은 카본블랙 3 %, 산화철 5%를 사용한 경우로 판단된다.

• 한국표면공학회지
• /
• 제53권2호
• /
• pp.80-86
• /
• 2020

This paper is concerned with type of imperfections present within the anodic oxide films on AA2024 and surface hardness of the anodic film measured after ink-impregnation. The anodic oxide films were formed for 25 min at 40 mA/㎠ and 15±0.5℃ and 300 rpm of magnet stirring rate in 20% sulfuric acid solution. The ink-impregnation allows clear observations of not only the imperfections within the anodic oxide films but also an indentation mark on the oxide film surface made by a pyramidal-diamond penetrator for the hardness measurement. There were observed four different regions in the anodic oxide films on AA2024 and the surface hardness of the anodic oxide films appeared to be crucially dependent on the type of defects, showing 60~100 H_v on the oxide surface region I with large size black defect, 100~140 H_v on the oxide surface region II with large size grey defect, 140~170 H_v on the oxide surface region III with mall size black and/or grey defects and 170~190 H_v on the oxide surface region IV without defects. The pyramidal indentation marks were observed to be distorted in the regions with a large size black and grey defects, while no distortion of the indentation mark was observed in the regions with small size defects and without visible defects.

• 품질경영학회지
• /
• 제24권1호
• /
• pp.96-109
• /
• 1996

In this paper, we consider the quality problem of black oxide process in casting for which Taguchi method is used. We explain simply the Taguchi method and existing problems in Black Oxide process. We analyze the problem by the quality improvement procedure proposed by Taguchi. The design factors and noises using cause-effect diagram are found, the experiment is made using orthogonal array. After ANOVA, the critical factors are determined and the optimal process condition is designed. After parameter design, we derive the tolerance levels. As a result of changing the levels of process parameters, the variance of quality characteristic was decreased by quarter and the average value was also decreased by half. We estimated the predictable profit of the improvement.

• 한국표면공학회지
• /
• 제29권4호
• /
• pp.238-252
• /
• 1996

In order to study the effect of interface oxides on the adhesion strength of the copper/epoxy system, copper foils were immersed in black oxide or brown oxide forming solutions before lamination with epoxy prepregs, and variation of peel strength with the treatment time were investigated. Results showed that peel strength decreased rapidly up to 1 minute of treatment lime and remained constant in the case of the black oxide treated specimens, which was accompanied by the thickening of $Cu_2O$ at the Copper/Epoxy interface during the period. In contrast, peel strength increased rapidly up to 1 minute of treatment time and remained constant in the case of the brown oxide treated specimens, which could be ascribed to the thickening of CuO. Subsequent heat treatments of the Copper/Epoxy laminations at $120^{\circ}C$ in air showed that peel strength remained constant in the case of the black oxide treated specimens but decreased gradually in the case of the brown oxide treated specimens. Following XPS analyses revealed that the latter was possibly caused by the coalescence of CuO at the Copper/Epoxy interface into $Cu_2O$.

• 한국재료학회지
• /
• 제29권11호
• /
• pp.709-714
• /
• 2019

In order to observe the microstructure and morphology of porous titanium -oxide thin film, deposition is performed under a higher Ar gas pressure than is used in the general titanium thin film production method. Black titanium thin film is deposited on stainless steel wire and Cu thin plate at a pressure of about 12 Pa, but lustrous thin film is deposited at lower pressure. The black titanium thin film has a larger apparent thickness than that of the glossy thin film. As a result of scanning electron microscope observation, it is seen that the black thin film has an extremely porous structure and consists of a separated column with periodic step differences on the sides. In this configuration, due to the shadowing effect, the nuclei formed on the substrate periodically grow to form a step. The surface area of the black thin film on the Cu thin plate changes with the bias potential. It has been found that the bias of the small negative is effective in increasing the surface area of the black titanium thin film. These results suggest that porous titanium-oxide thin film can be fabricated by applying the appropriate oxidation process to black titanium thin film composed of separated columns.

• 생명과학회지
• /
• 제7권4호
• /
• pp.309-315
• /
• 1997

The fermented black tea with tea fungus (FBTF) was prepared by culturing tea fungus biomass in black tea with 10% sucrose (BT) at 30$\circ$ for 14 days. The flavor quality of FBTF was investigated by sensory and chemical analysis, and the results were compared with BT. The data of sensory analysis indicated that fruity, wine-like, sharp-pungent, and vinegar-like flavor notes were increase, while earthy note was reduced during fermentation. GC-MS analysis of volatile compounds collected from FBTF and BT by Tenax trap showed that linalool, liinalool oxide other flavor compounds known as black tea flavor compounds were disappeared. Some major flavor compounds produced during fermentation were acetic acid, ethanol, limonene, $\alpha$-terpineol, and these volatiles may be attributed to the flavor of characteristic FBTF. Biosynthetic pathway for the formation of limonene and $\alpha$-terpineol are proposed through mevalonic acid pathway using acetic acid as precusor and/or through transformation of linalool and linalool oxide.

• 한국재료학회지
• /
• 제15권1호
• /
• pp.1-5
• /
• 2005

Copper-based leadframe sheets were immersed in two kinds of hot alkaline solutions to form brown-oxide or black-oxide layer on the surface. The oxide-coated leadframe sheets were molded with epoxy molding compound (EMC). After post mold curing, the oxide-coated EMC-leadframe joints were machined to form sandwiched double-cantilever beam (SDCB) specimens. The SDCB specimens were used to measure the fracture toughness of the EMC/leadframe interfaces under quasi-Mode I loading conditions. Fracture surfaces were analyzed by various equipment to investigate failure path. The present paper deals with the failure path, and the cause of the failure path formation with an adhesion model will be treated in the succeeding paper.

• 한국농공학회지
• /
• 제27권2호
• /
• pp.57-71
• /
• 1985

The characteristics of compaction and unconfined compressive strength were investigated by mixing with lime to all soils adjusted by given percentages of two kinds of clays to sand to obtain the most effective distribution of grain size and the optimum lime content for soil stabilization. In addition, unconfined compressive strength and durability tested by adding of sodium metasilicate, sodium sulfate, sodium carbonate, sodium gydroxide and magnesium oxide to lime-soil mixture mixed with 8 percent lime to adjusted soil having the mixing percentage of 60 percent of cohesive black clay and 40 percent of sand by weight to get the effect and the optimum content of chemicals. The results obtained were as follows; 1.With the addition of more lime, the optimum moisture content was increased, and the maximum dry density was decreased, whereas the more the amount of clay and the less was the maximum drt density. 2. In the soil having more fine grain size the unconfined compressive strength was larger in the earlier stage of curing period, in accordance with the longer period, the mixing percentages of sand to clay showing the maximum unconfined compressive strength, on the basis of 28-day strength, were 60% : 40% (black clay) and 40% : 60% (brown clay) respectively. 3. The reason why the soil adjusted with black clay was remarkably bigger in the unconfined compressive strength than ones adjusted with brown clay for all specimen of lime-soil mixture was the difference in the kind of clay, the amount of chemical compositions the value of pH. Black clay was mainly composed of halloysite that reacted with lime satisfactorily, whereas the main composition of brown clay was kaolinite that was less effect in the enhance of unconfined compressive strength. Also the difference of unconfined compressive strength was because black clay was larger in the amount of composition of calcium oxide and magnesium oxide in the value of pH affecting directly on the unconfined compressive strength of lime-soil mixture than brown clay. 4. In the lime-soil mixture mixed with 8 percent of lime to soil that mixing percentage of sand to black clay was 60% : 40%, on the standard of 7-day strength, the effect of chemical was arranged in the order of magnesium oxide, sodium carbonate, sodium sulfate, sodium hydroxide and sodium metasilicate. 5. The optimum amount of chemical being applicable to the maximum unconfined compressive strength of lime-chemical-soil mixture was 1 percent by weight for air dry soil in the case of adding sodium carbonated and 0.75 percent on sodium hydroxide, the unconfined compressive strength was increased continuously with increase of the amount of chemical up to 2 percent of chemical content is the lime-chemical-soil mixture added sodium metasilicate, sodium sulfate and magnesium oxide. 6. It was considered that the chemical played and accelerant role of early revelation of strength because the rate of increase of unconfined compressive strength of all of lime-chemical-soil mixtures was largest on the 7-day cured specimen. 7. The effect of test on freezing and thawing after adding suitable amount of chemical on the lime-soil mixture mixed with 8 percent of lime to soil that mixing percentage of sand to black clay was 60% : 40% was arranged in the order of magnesium oxide, sodium carbonate, sodium sulfate, sodium metasilicate and sodium hydroxide.